BLOTZ B10-MW-003 Assembly Instructions

Brand
BLOTZ
Model
B10-MW-003
Category
Car kits
Type
Assembly Instructions
10mm 5x3 Residential
B10-MW-003
This is a model kit and is not suitable for those under 12 years.
This kit consists of:
B10-MW-102: Foyer (2 sheets)
B10-MW-152: Middle (2 sheets)
B10-MW-202: Roof (2 sheets)
Please refer to the website for
assembly instructions.
Blotz
90 Fullers Avenue
Cricklade
SN6 6EU
[email protected]
www.blotz.co.uk
10mm 5x3 Residential Foyer
B10-MW-102
Please read these instructions fully before starting construction.
PVA or equivalent glue will be required to stick sections together.
Sand paper can be used to gently clean any joints.
A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due
care and remember to cut away from yourself at all times.
During the construction of this model, you may find it convenient to use pegs / elastic bands to hold
pieces in place while you allow glue to dry.
Foyer (B10-MW-102)
Start by removing the sections shown above (left)
from the sprue. There are enough parts to create
both doorway sections.
Glue them together as shown in the image on the
right.
Glue each doorway to the back of the long sides, using
the lugs/holes provided.
At the same time, glue a triangular bracer to the
back of the long sides at each end. Leave these to
dry.
Glue the shorter end walls into place to give a hollow
rectangle.
Finally glue the decorative columns into position.
10mm 5x3 Residential Middle
B10-MW-152
Please read these instructions fully before starting construction.
PVA or equivalent glue will be required to stick sections together.
Sand paper can be used to gently clean any joints.
A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due
care and remember to cut away from yourself at all times.
During the construction of this model, you may find it convenient to use pegs / elastic bands to hold
pieces in place while you allow glue to dry.
Mid-Section (B10-MW-152)
Remove the four walls and four triangular corner
bracers from the sprue. Glue the triangles to
non-etched side of the two long walls as shown
in the example above. Leave to dry.
Once the bracers are dry, apply a little glue to the side
lugs and glue the shorter walls in place as shown
above. You should now have a hollow square
structure.
Leave it to dry.
Now remove the four rectangles from the sprue.
Each of these has a line etched across it. Apply
glue to one side of the line only and attach it (as
shown) to the centre bottom edge of each wall.
The finished mid-section.
10mm 5x3 Residential Roof
B10-MW-202
Please read these instructions fully before starting construction.
PVA or equivalent glue will be required to stick sections together.
Sand paper can be used to gently clean any joints.
A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due
care and remember to cut away from yourself at all times.
During the construction of this model, you may find it convenient to use pegs / elastic bands to hold
pieces in place while you allow glue to dry.
Roof Section (B10-MW-202)
Remove the four walls and roof from the sprue.
Apply glue to the edges of the roof and attach
the walls to it using the lugs provided (etched
detail outwards).
Glue the decorative strips into position above the
windows.
Now remove the four rectangles from the sprue.
Each of these has a line etched across it. Apply glue to
one side of the line only and attach it (as shown in the
example above) to the centre bottom edge of each
wall.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

BLOTZ B10-MW-003 Assembly Instructions

Brand
BLOTZ
Model
B10-MW-003
Category
Car kits
Type
Assembly Instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers