Page is loading ...
FSR 244 Bergen Boulevard, Woodland Park, NJ 07424, Phone: 973.785.4347 - Fax: 973.785.4207
43158 LIT1586A
PRIOR TO PUSHING CEILING BOX INTO FRAME, APPLY BLUE PAINTERS TAPE (OR
EQUIVALENT) TO THE FRAME'S PAINTED BORDER, TO HELP PREVENT SCRATCHING THE
PAINT UPON BOX INSTALLATION. LINE UP THE BOX AND PUSH CEILING BOX UP INTO
FRAME. WHEN CEILING BOX REACHES THE STOPS ON THE INSIDE OF THE FRAME, PUSH
PINS INTO CAPTURE BRACKETS TO HANG BOX IN PLACE. IMPORTANT! - INSTALL PIN
LABELS, APPROXIMATELY WHERE SHOWN, ON BOTH SIDES. REFER TO CEILING BOX
INSTALLATION INSTRUCTIONS TO COMPLETE INSTALLATION. REMOVE TAPE ON
COMPLETION OF INSTALLATION.
5.
(4) CAPTURE BRACKET
INSDE FRAME
PIN (UNLOCKED POSITION)
(2) PIN LABEL
INSTALL 2ND LABEL
ON OPPOSITE SIDE
PIN (LOCKED POSITION)
INSTALLATION OF THE CB-SR22 CEILING FRAME REQUIRES A ROUGH-IN HOLE IN THE CEILING OF 25" SQUARE, +/- 1/16". THE
HOLE'S ROUGH-IN STRUCTURE NEEDS TO BE A MINIMUM OF 1-1/2" TALL, AND MAY BE MADE OF METAL OR WOOD.
1.
CB-SR22 INSTALLATION INSTRUCTIONS
BY FOUR STEEL THREADED RODS, ONE PER CORNER OF THE FRAME, 1/4-20 THREAD MINIMUM TO 3/8-16 THREAD MAXIMUM,
CENTERED ON A SQUARE 23-1/2" APART, AND EXTENDING DOWN TO WITHIN 2" TO 6" OF THE CEILING'S IN-ROOM SURFACE.
1)
2) BY STEEL HANGER CABLE, 3/32"-DIAMETER MINIMUM, AND THREADED THRU THE FRAME'S APPROPRIATE SLOTS/HOLES IN
THE CORNERS OF THE UNIT.
3) BY SCREWS THRU THE APPROPRIATE HOLES IN THE CORNERS OF THE FRAME, INTO THE CEILINGS ROUGH-IN OPENING
STRUCTURE. TWO SCREWS, MINIMUM, PER CORNER.
THE SELECTED MOUNTING METHOD MUST BE ABLE TO SUPPORT A MINIMUM OF 500 LBS, AND BE APPROVED FOR
OVERHEAD LOADING.
SLOTTED OPENING
FOR THREADED
ROD OR CABLE
FRAME CORNER DETAIL
HOLE FOR CABLE
HOLES FOR SCREWS
THREADED ROD CABLE SCREW
THREADED ROD (2) NUT &
(2) WASHER CABLE
QUICK ADJUST
CABLE CLAMP
ROUGH-IN
STRUCTURE
(MINIMUM HEIGHT
SHOWN)
SCREW
CEINLING BOX UNLOCKED AND LOWERED
CEILING BOX RAISED AND LOCKED
THERE ARE 3 METHODS BY WHICH THE FRAME CAN BE RETAINED IN THE CEILING:
THE STEPS REQUIRED TO MOUNT THE CEILING FRAME ARE:
A) DETERMINE THE MOUNTING METHOD APPROPRIATE FOR THE CEILNG CONSTRUCTION.
B) CREATE THE ROUGH-IN OPENING STRUCTURE AND INSTALL UNIT SUPPORTING HARDWARE AS NEEDED.
C) INSTALL CEILING/DRYWALL, TRIM TO ROUGH-IN OPENING.
D) TAPE/SPACKLE THE CEILING DRYWALL, AND PAINT IT IF THE CEILING COLOR IS TO BE DIFFERENT THAN THAT OF
THE CEILING FRAME'S VISIBLE WHITE ROUGH-IN-OPENING COVER.
E) INSTALL THE CEILING FRAME, THEN PROCEED TO INSTRUCTION STEP #2, AND COMPLETE THE UNIT INSTALLATION.
(4) GUIDE BRACKET
ENSURE BRACKETS ARE
CORRECTLY LOCATED.
NOTE CABLE LOCATIONS
ON BRACKETS. CABLES
WILL BE LOCATED
FURTHEST FROM
CENTER OF BOX.
(4) CABLE
TOP VIEW
LOOSEN SHELF SCREWS
AND REMOVE SHELVES TO
INSTALL PIN BRACKETS
SIDE CONDUIT
KNOCKOUT
SIDE CONDUIT
KNOCKOUT
(4) GUIDE
BRACKET
(NOTE CABLE
LOCATION)
(4) PIN BRACKET
(8) #8-32 x 3/8 LONG
PAN HEAD SCREW
BRACKET DETAIL
PIN DETAIL
CEILING BOX
(SOLD SEPARATELY)
2. INSTALL BRACKETS INTO CEILING BOX (SOLD SEPARATELY). CEILING BOX
SHELVES WILL HAVE TO BE REMOVED FOR INSTALLATION OF BRACKETS
(SEE BRACKET DETAIL AND TOP VIEW). INSERT PINS INTO BRACKETS
UNTIL FLUSH WITH CEILING BOX EXTERIOR WALL (SEE PIN DETAIL).
3. ALIGN THE CEILING BOX, WITH ITS NEW BRACKETS, WITH THE CAPTURE BRACKETS
INSIDE FRAME. ATTACH 2 CABLES FROM CEILING BOX (NEAREST THE BOX'S KO'S) TO
FRAME AND ROUTE WIRING INTO CEILING BOX.
AFTER ALL WIRING IS ROUTED TO CEILING BOX, ATTACH REMAINING CABLES TO FRAME.
4.
GUIDE BRACKET
(4) PIN
INSERT PIN UNTIL FLUSH
WITH EXTERIOR WALL
OF CEILING BOX
NOTE: ALL ELECTRICAL WIRES MUST DRAPE OVER THE TOP EDGE OF THE CEILING
BOX FRAME, NOT THRU THE SIDE OPENINGS. ONLY THE TOP-SURFACE KO'S
OF THE CEILING BOX MAY BE USED FOR THE WIRING.
CABLE INSTALLATION
OPENING
IN FRAME
CABLE
a. INSERT LARGE TAB
OF CABLE INTO
LARGE OPENING.
b. INSERT SMALL TAB
OF CABLE INTO
SMALL OPENING.
c. SLIDE CABLE
DOWNWARD TO
FLOOR.
d. INSTALL #6 SCREW
TO SECURE CABLE
TO FRAME.
(4) PIN
/
