FSR 244 Bergen Boulevard, Woodland Park, NJ 07424, Phone: 973.785.4347 - Fax: 973.785.4207
43019 LIT1406
CHASSIS ASSEMBLY
(AVAILABLE WITHOUT KO'S)
MAKE ELECTRICAL CONNECTIONS AS REQUIRED.
6.
5.
4.
3.
2.
STEPS:
7.
REINSTALL MOUNTING PLATES AS SHOWN IN
FIGURE 1. USE SEPARATOR AS REQUIRED.
GANG-UNIT END SEPARATOR IS MOVEABLE
SIDE-TO-SIDE OF CENTER OF END, OR CAN BE
REMOVED ALTOGETHER. AFTER DETERMINATION
OF SEPARATOR, REINSTALL GANG-UNIT ENDS AS
SHOWN IN FIGURE 2.
ROUTE CONDUITS TO CHASSIS, AND PULL
WIRES AS REQUIRED.
INSTALL CHASSIS INTO WALL PER INSTRUCTIONS
AT THE END OF THIS DOCUMENT.
REMOVE UPPER/LOWER GANG-UNIT END FROM
CHASSIS AS SHOWN IN FIGURE 2, SETTING
GANG-UNIT ENDS AND SCREWS ASIDE.
1. REMOVE ASSEMBLED MOUNTING PLATES
FROM CHASSIS AS SHOWN IN FIGURE 1,
SETTING PLATE AND SCREWS ASIDE.
WB-X3-GNG
WB-X3-GNG / WB-X3-IPS / WB-X3-PLT / WB-X3-XLR INSTALLATION INSTRUCTIONS
FIGURE 1
FIGURE 2
(2) SEPARATOR
ASSEMBLED 2G/4G
MOUNTING PLATE
UPPER END OF CHASSIS
UPON INSTALLATION
ASSEMBLED 2G/2G
MOUNTING PLATE
(2) SEPARATOR
(2) GANG-UNIT END
SEPARATOR
ALTERNATE
LOCATION
2.
INSTALL CHASSIS INTO WALL PER
INSTRUCTIONS AT THE END OF THIS
DOCUMENT.
MAKE ELECTRICAL CONNECTIONS AS REQUIRED.
INSTALL FRAME ASSEMBLY AS SHOWN IN
FIGURE 4.
3.
STEPS:
1.
5. INSTALL IPS WALLBOX BUCKETS AS SHOWN IN
FIGURE 5.
6.
4.
ASSEMBLE FRAME ASSEMBLY AS SHOWN IN
FIGURE 3.
ROUTE CONDUITS TO CHASSIS, AND PULL
WIRES AS REQUIRED.
CHASSIS ASSEMBLY
(AVAILABLE WITHOUT KO'S)
WB-X3-IPS
NOTE: ASSEMBLE
FRAME AS SHOWN ON
A FLAT SURFACE
FIGURE 3
FIGURE 4 FIGURE 5
NOTE SLOT
(4) #8-32x1/4" FLAT HEAD SCREW
(LOCTITE RECOMMENDED)
IPS LOWER INTERIOR
SUPPORT BRACKET
IPS UPPER INTERIOR
SUPPORT BRACKET
(2) IPS BUCKET
MOUNTING BRACKET
(6) #8-32x1/4" FLAT
HEAD SCREW
NOTE SLOT LOCATION, WHICH
DESIGNATES UPPER END OF
CHASSIS UPON INSTALLATION
FRAME ASSEMBLY
(12) #8-32x1/4" FLAT
HEAD SCREW
UPPER END OF
CHASSIS UPON
INSTALLATION
(3) IPS WALLBOX
BUCKET
CHASSIS ASSEMBLY
(AVAILABLE WITHOUT KO'S)
INSTALL BRACKET ASSEMBLIES AS SHOWN IN FIGURE 7.
MAKE ELECTRICAL CONNECTIONS AS REQUIRED.
INSTALL CHASSIS INTO WALL PER INSTRUCTIONS AT THE END
OF THIS DOCUMENT.
6.
3.
ROUTE CONDUITS TO CHASSIS, AND PULL WIRES AS REQUIRED.
STEPS:
5. MODIFY BLANK PLATE AS NECESSARY TO MOUNT DESIRED
COMPONENTS. INSTALL THIS PLATE AS SHOWN IN FIGURE 8.
ASSEMBLE BRACKET ASSEMBLY AS SHOWN IN FIGURE 6.
4.
2.
1.
WB-X3-PLT
FIGURE 6
FIGURE 7 FIGURE 8
(3) #8-32x3/8" PAN
HEAD SCREW
BLANK PLATE MOUNTING BRACKET
MOUNTING
BRACKET
SUPPORT
HEIGHT ADJUSTMENT HOLE
(ENSURE BOTH BRACKET ASSEMBLIES
ARE USING THE SAME HOLES)
(6) #8-32x1/4" FLAT
HEAD SCREW
BRACKET
ASSEMBLY
BRACKET
ASSEMBLY
BLANK PLATE
(6) #8-32x3/8" PAN
HEAD SCREW
COMPONENT AREA
CHASSIS ASSEMBLY
(AVAILABLE WITHOUT KO'S)
6.
INSTALL CHASSIS INTO WALL PER INSTRUCTIONS
AT THE END OF THIS DOCUMENT.
ROUTE CONDUITS TO CHASSIS, AND
PULL WIRES AS REQUIRED.
ASSEMBLE FRAME ASSEMBLY AS SHOWN
IN FIGURE 9.
INSTALL FRAME ASSEMBLY AS SHOWN IN
FIGURE 10.
INSTALL XLR WALLBOX BUCKETS AS SHOWN IN
FIGURE 11.
STEPS:
1.
2.
3.
4.
5.
MAKE ELECTRICAL CONNECTIONS AS REQUIRED.
UPPER END OF
CHASSIS UPON
INSTALLATION
NOTE: ASSEMBLE
FRAME AS SHOWN ON
A FLAT SURFACE
FIGURE 10 FIGURE 11
FIGURE 9
WB-X3-XLR
NOTE STRAIGHT SURFACE
(2) XLR BUCKET
MOUNTING BRACKET
XLR LOWER INTERIOR
SUPPORT BRACKET
NOTE SLOT
IPS UPPER INTERIOR
SUPPORT BRACKET
(4) #8-32x1/4" FLAT HEAD SCREW
(LOCTITE RECOMMENDED)
NOTE STRAIGHT SURFACE,
WHICH DESIGNATES
UPPER END OF CHASSIS
UPON INSTALLATION
(6) #8-32x1/4" FLAT
HEAD SCREW
NOTE SLOT
FRAME ASSEMBLY
(16) #8-32x1/4" FLAT
HEAD SCREW
(4) XLR WALLBOX
BUCKET
5.
3.
1.
MOUNT CHASSIS ASSEMBLY TO WALL AS
SHOWN IN FIGURE 14.
ENSURE AT LEAST 3" OF BLOCKING MATERIAL
BEYOND BOTH UPPER AND LOWER EDGES OF
CUT-OUT.
CUT A 12-1/2" x 16-7/8" OPENING IN WALL
CENTERED BETWEEN THE STUDS.
WB-X3 INSTALLATION (OLD-WORK)
4.
2.
STEPS:
INSTALL OLD-WORK MOUNTING BRACKET TO
CHASSIS ASSEMBLY AS SHOWN IN FIGURE 13.
INSTALL SCREW/CLAMP BLOCK ALONG EDGE OF
CUT-OUT AS SHOWN IN FIGURE 12 - SEE STEP 3.
1" CUSTOMER-SUPPLIED
BLOCKING - 5/4 WOOD
MATERIAL RECOMMENDED
2 x 4 STUDS
16" ON CENTER
SCREW/CLAMP BLOCK
(8) CUSTOMER-
SUPPLIED
#8 WOOD SCREW
1/2" OR 5/8" DRYWALL
CHASSIS ASSEMBLY
(AVAILABLE WITHOUT KO'S)
(2) OLD-WORK
MOUNTING
BRACKET
(8) #8-32 SCREW
(SUPPLIED)
FIGURE 12
FIGURE 13 FIGURE 14
(8) CUSTOMER-SUPPLIED
#8 WOOD SCREW
(AFTER CHASSIS IS IN
POSITION IN WALL)
2.
INSTALL (2) MOUNTING BRACKET TO CHASSIS
ASSEMBLY AS SHOWN IN FIGURE 15.
INSTALL BOX ASSEMBLY ONTO STUDS
AS SHOWN IN FIGURE 16.
STEPS:
WB-X3 INSTALLATION (NEW-WORK)
1.
FIGURE 16
FIGURE 15
(2) NEW-WORK
MOUNTING
BRACKET
(8) #8-32 SCREW
(SUPPLIED)
CHASSIS ASSEMBLY
(AVAILABLE WITHOUT KO'S)
CUSTOMER-SUPPLIED
#8 WOOD SCREWS,
NAILS OR STAPLES
2 x 4 STUDS, 16" ON CENTER
CENTER-ON-STUDS ASSIST NOTCHES
(LINE UP NOTCH EDGES WITH STUD
INNER EDGES TO CENTER CHASSIS
BETWEEN STUDS)
/
