Tele Radio T27-02 Operating instructions

Brand: Tele Radio

Model: T27-02

Type: Operating instructions

This manual is also suitable for

T27
T27-01

safe smart strong

T27

ED-PN-TX107-EN-v01

Language: English (original)

ENDUSER

INSTRUCTIONS

Transmitters: T27-01, T27-02

©Tele Radio AB

Datavägen 21

SE-436 32 Askim

Sweden

Phone: +46 (0)31 748 54 60

CHAPTER 1: INTRODUCTION 5

1.1About this document 7

1.2About T27 transmitters 8

CHAPTER 2: SAFETY 9

2.1Warnings & restrictions 9

2.2Safety features 11

CHAPTER 3: TECHNICAL DATA 12

3.1Transmitter specifications 12

3.2Other specifications 13

CHAPTER 4: PRODUCT GENERAL DESCRIPTION 15

4.1Transmitter dimensions 15

4.2Transmitter top views 16

4.3Transmitter bottom view 18

4.4Transmitter side views 19

4.5Display and display LEDS 21

4.6Side buttons 22

CHAPTER 5: STATUS AND ERROR INDICATIONS 23

5.1Display LEDs status and error codes 23

5.2Errorindications and messages 23

CHAPTER 6: OPERATION 24

6.1General information 24

6.2General navigation 24

6.3Start-up protection 25

6.4Functionality test 26

6.5Log the transmitter in to a receiver (Start a session) 27

6.6Quick logout 28

6.7Switch the transmitter off 28

CHAPTER 7: BATTERY 29

7.1Battery precautions 29

7.2Battery information 31

CHAPTER 8: WARRANTY, SERVICE, REPAIRS, AND MAINTENANCE 33

CHAPTER 9: REGULATORY INFORMATION 34

9.1Europe 34

9.2North America 34

ANNEX A: INDEX 37

Enduser instructions│T27│Chapter 1: Introduction

CHAPTER 1: INTRODUCTION

Thank you for using a Tele Radio AB product

READ ALL INSTRUCTIONS AND WARNINGS CAREFULLY BEFORE OPERATING

THE PRODUCTS.

These End user instructions have been published by Tele Radio AB and are not

subject to any guarantees. The End user instructions may be withdrawn or revised

by Tele Radio AB at any time and without further notice. Corrections and updates

will be added to the latest version of the manual. Always download the End user

instructions from our website, www.tele-radio.com, for the latest available version.

Keep the safety instructions for future reference.

IMPORTANT! These instructions are intended for end users. The instructions can be

printed and handed to end user.

Tele Radio AB remote controls are often built into wider applications. This

documentation is not intended to replace the determination of suitability or

reliability of the product for specific user applications and should not be used for

this purpose. It is the responsibility of any such users or integrators to perform the

appropriate and complete risk analysis, evaluation and testing of the products with

respect to the relevant specific application or use. Tele Radio AB shall not be

responsible or liable for misuse of the information contained herein.

Always refer to the applicable local regulations for installation and safety

requirements relating to cranes, hoists, material handling applications, lifting

equipment, industrial machinery, and/or mobile hydraulic applications using Tele

Radio AB products, e.g.:

lapplicable local and industrial standards and requirements,

lapplicable occupational health and safety regulations,

lapplicable safety rules and procedures for the factory where the equipment

is being used,

luser and safety manuals or instructions of the manufacturer of the

equipment where Tele Radio AB remote control systems are installed.

Tele Radio AB End user instructions do not include or address the specific

instructions and safety warnings of the end product manufacturer.

For battery precautions, see "7.1 Battery precautions".

ED-PN-TX107-EN-v01 5

Enduser instructions│T27│Chapter 1: Introduction

Tele Radio AB products are covered by a warranty against material, construction, or

manufacturing faults. See "Chapter 8: Warranty, service, repairs, and maintenance".

6 ED-PN-TX107-EN-v01

Enduser instructions│T27│Chapter 1: Introduction

1.1About this document

Before installing or operating the product, read the corresponding documentation

carefully.

Tele Radio AB's product range is composed of transmitters, receivers, and

accessories intended for use together as a system.

These End user instructions cover general safety issues, main technical

specifications, standard operating instructions and battery information. Images

shown in this document are for illustrative purposes only.

Please report any error or omission in this document, as well as any improvement

or amendment suggestion to td@tele-radio.com.

1.1.1COPYRIGHT

Information in this document is subject to change without notice. No part of this

publication may be reproduced, stored in a retrieval system, or transmitted in any

form or by any means, electronic, photographic, mechanical (including

photocopying), recording or otherwise for any purpose other than the purchaser's

personal use without the written permission of Tele Radio AB.

1.1.2TERM AND SYMBOL DEFINITIONS

The capitalized terms and symbol used herein shall have the following meaning:

lWARNING: indicates a hazardous situation which, if not avoided, could result

in death or serious injury.

lCAUTION: indicates a hazardous situation which, if not avoided, will result in

minor or moderate injury.

lIMPORTANT: is used for information that requires special consideration.

lNOTE: is used to address practices not related to physical injury.

This symbol is used to call attention to safety messages that would be

assigned the signal words "WARNING"or "CAUTION".

ED-PN-TX107-EN-v01 7

Enduser instructions│T27│Chapter 1: Introduction

1.2About T27 transmitters

1.2.1BASE MODEL

T27 transmitters have duplex communication and work in continuous mode.

NOTE: Base models are meant to be customized according to customer or

application requirements.

There is one base model available.

Model Main boards

Base board Bottom board RFID Joystick IOs Paddle IOs Hall effect

T27-01 ● ● ○ ○ ○

(1)

○

(1)

●Standard ○Optional1– Not available

Model Blank front Stop button on the side Key switch RFID Cable control

T27-01 ● ● ○ ○ –

●Standard ○Optional1– Not available

1.2.2STANDARD MODEL

NOTE: Standard models are pre-configured.

There is one standard model available.

Model Main boards

Base board Bottom board

T27-02 ● ●

●Standard – Not available

Model Front Stop button on the side

T27-02 2 joysticks, 2 toggle switches ●

●Standard – Not available

1Must be purchased separately.

8 ED-PN-TX107-EN-v01

Enduser instructions│T27│Chapter 2: Safety

CHAPTER 2: SAFETY

2.1Warnings & restrictions

Carefully read through the following safety instructions before

proceeding with the installation, configuration, operation, or

maintenance of the product. Failure to follow these warnings could

result in death or serious injury.

This product must not be operated without having read and understood the

Enduser instructions and having received the appropriate training. The purchaser

of this product has been instructed how to handle the system safely. The following

information is intended for use as a complement to applicable local regulations

and standards.

IMPORTANT! Tele Radio AB remote controls are often built into wider

applications. These systems should be equipped with:

• a wired emergency stop where necessary

• a brake

• an audible or visual warning signal

2.1.1OPERATION

This radio system must not be used in areas where there is a risk of

explosion.

Only qualified personnel should be permitted to access the transmitter

and operate the equipment.

This equipment is not suitable for use in locations where children are

likely to be present.

ED-PN-TX107-EN-v01 9

Enduser instructions│T27│Chapter 2: Safety

lAlways follow operating and maintenance instructions as well as all

applicable safety procedures and requirements.

lDo not open the receiver encapsulation unless you are qualified.

lYou must satisfy the age requirements in your country for operating

the equipment.

lIt is strictly prohibited to operate the equipment under the

influence of drugs, alcohol and/or medications.

lAlways test the transmitter stop button before operating it. Press

the stop button then twist and pull it out. This test should be done

on each shift, without a load.

lNever use a transmitter if the stop button is mechanically

damaged.Contact your supervisor or representative for service

immediately.

lNever leave the transmitter unattended.

lAlways switch the transmitter off when not in use. Store in a safe

place.

lKeep a clear view of the work area at all times.

2.1.2MAINTENANCE

Before maintenance intervention on any remote controlled equipments:

• always remove all electrical power from the equipment.

• always follow lockout procedures.

lKeep the safety information for future reference. Always download the

Enduser instructions from our website, www.tele-radio.com, for the latest

available version.

lIf error messages are shown, it is very important to find out what caused

them. Contact your representative for help.

lThe functionality of the stop button should be tested at least after every 200

hours’ use (see "2.2.1 Stop button").

lIf the stop button is mechanically damaged, do not use the transmitter.

Contact your supervisor or representative for service immediately.

lKeep the product in a clean, dry place.

lDo not try to open the encapsulation.

10 ED-PN-TX107-EN-v01

Enduser instructions│T27│Chapter 2: Safety

lAlways contact your representative for service and maintenance work on the

product.

lKeep contacts and antennas clean.

lWipe off dust using a clean, slightly damp cloth.

lNever use cleaning solutions.

lCheck the encapsulation, foils and cable for damages every day. If you use

the product although the encapsulation or foil is damaged, moisture can

cause serious damage to the electronics.

2.2Safety features

2.2.1STOP BUTTON

Tele Radio AB transmitters are equipped with a stop button.

When the Stop button is pressed, the stop relays on the

receiver deactivate.

IMPORTANT! The Stop button should always be tested before operating the

transmitter. This test should be done on each shift, without a load.

To test the stop button:

1. Press the Stop button.

2. Twist and release the Stop button.

ED-PN-TX107-EN-v01 11

Enduser instructions│T27│Chapter 3: Technical data

CHAPTER 3: TECHNICAL DATA

NOTE: The information below may differ in customized systems, please refer to

the corresponding technical documentation provided with each system.

3.1Transmitter specifications

Power supply One (1) replaceable, rechargeable lithium-ion battery

Battery pack 3.7V / 1600mAh Li-ion – 1 battery compartment

Current consumption From 130mA (depending on the configuration)

Operating time Up to 10h (depending on the configuration)

Radio frequency band 2405 – 2480MHz

Frequency management Direct Sequence Spread Spectrum (DSSS)

Number of Channels 16 (channel 11 – 26)

Range (typical) 100 m (328 ft), adjustable depending on configuration

Radio frequency output

power

EIRP1< 12.5dBm (18mW)

Antenna Internal (external in option)

Display LCD 2.2" TFT. Active area 45x33.8mm (1.77x1.33in)

Resolution: 320 x 240 px

Graphic / pixels with backlight sensor

Standard and Custom configurations

Safety levels EN ISO 13849-1,CAT3 PLd (Stop function)

IP code IP65

Operating temperature -20…+55°C / -4…+130°F

Storage temperature -30…+70°C / -22…+158°F (without battery)2

Charging temperature +10…+35 °C / +50…+95 °F

1Equivalent isotropic radiated power

2For storage temperature of battery pack M245060 (D4-02), see "7.2 Battery information".

12 ED-PN-TX107-EN-v01

Enduser instructions│T27│Chapter 3: Technical data

3.2Other specifications

T27-01 T27-02

Number of

joysticks

○2, 2-axis with spring return for analogue control

directions1.

Number of

paddles

○–

Number of

switches

○2, toggle switch (On)–None–(On)

upper switch Momentary function (spring return)

lower switch Stay-put function

Stop button On the side

Key switch ○ ○

RFID ○ ○

Cable control – –

Weight (typical) ~2kg (~4.4lbs)

●Standard ○Optional– : Not available

1see "Joystick directions" on next page.

ED-PN-TX107-EN-v01 13

Enduser instructions│T27│Chapter 3: Technical data

3.2.1JOYSTICK DIRECTIONS

T27-02 transmitter has two joysticks (2-axis with spring-to-centre) allowing a two

graduated steps control.

T27-02

Joystick 1 (XY) 2x2

Joystick 2 (XY) 0x2

Code (XY) Movement control

on X

Movement control

on Y

Movement control

on Z

0x2 – 2-step –

2x2 2-step 2-step –

2x0 2-step – –

4x4 4-step 4-step –

4x0 4-step – –

Analog XY stepless stepless –

Analog Y – stepless –

Analog XYZ stepless stepless stepless

Example:

Analog XY Analog Y

The joystick operates on both X and Y

axes with stepless movement from the

center.

The joystick/paddle operates on the Y

axe only with stepless movement from

center and back.

14 ED-PN-TX107-EN-v01

Enduser instructions│T27│Chapter 4: Product general description

CHAPTER 4: PRODUCT GENERAL DESCRIPTION

The pictures shown in this chapter are for illustrative purposes only.

4.1Transmitter dimensions

ED-PN-TX107-EN-v01 15

Enduser instructions│T27│Chapter 4: Product general description

4.2Transmitter top views

4.2.1T27-01

1. Handlebar

2. Status LED

3. LCD display

4. Battery LED

5. Customizable area1

6. Belt loops

1Paddles, joysticks, buttons, etcs. depending on the configuration.

16 ED-PN-TX107-EN-v01

Enduser instructions│T27│Chapter 4: Product general description

4.2.2T27-02

1. Handlebar

2. Joystick 1 (2x2)

3. Status LED

4. LCD display

5. Battery LED

6. Joystick 2 (0x2)

7. Toggle switch SW1 (1/0/1 spring

return)

8. Toggle switch SW2 (1–0-1

maintained)

9. Belt loops

ED-PN-TX107-EN-v01 17

Enduser instructions│T27│Chapter 4: Product general description

4.3Transmitter bottom view

1. Belt loops

2. Battery compartment

3. Stop button

4. Replaceable battery

5. RFID antenna (not implemented)

6. Product label

18 ED-PN-TX107-EN-v01

Enduser instructions│T27│Chapter 4: Product general description

4.4Transmitter side views

4.4.1T27-01

Lef side Right side

1. LCD display

2. Handlebar

3. SB1

4. SB2

5. SB4

6. SB3

7. Belt loops

8. Stop button

ED-PN-TX107-EN-v01 19

Enduser instructions│T27│Chapter 4: Product general description

4.4.2T27-02

Lef side Right side

1. LCD display

2. Handlebar

3. Toggle switch 1

4. Joysticks1

5. Toggle switch 2

6. Belt loops

7. SB1

8. SB2

9. SB4

10. Stop button

11. SB3

20 ED-PN-TX107-EN-v01

Page is loading ...

Tele Radio T27-02 Operating instructions

Brand: Tele Radio

Model: T27-02

Type: Operating instructions

This manual is also suitable for

T27
T27-01

Download PDF

report

Tele Radio T27-02 Operating instructions

This manual is also suitable for

Tele Radio T27-02 Operating instructions

Related papers

Other documents