5019 637 01025
Remove it from the box (found in the crisper drawer (item 5)) and
insert into the grille (item 1c). For any optimum performance of the
antibacterial filter, replace the filter every 6 months.
1. Remove the filter and dispose as a whole (grate box + insert).
2. Replace the filter with the new ones.
3. The replacement procedure is attached with the filter.
Our After-sales Service can supply this type of filter.
Replacing the light bulb
Always disconnect the refrigerator from the power supply before
replacing any light bulb. If the inside light is not working, it is
necessary to:
1. Remove the light cover: put the fingers into the side ventilation
holes (1), stretch the cover gently and move it upwards.
2. Check the bulb. If necessary unscrew the broken bulb and replace
it with the new one (use maximum 15W bulb).
3. Assembly again the light cover pushing in its place. Do not leave
uncovered bulb.
GUIDE TO SELECTING FUNCTIONS
Functions and settings
Alarm deactivation - the user have to press two pushbutton
temperature setting and vacation mode parallel.
Fast Freezing: Activate this function before freezing fresh products
- Press steps by the “Temperature setting” button to start the
function - 3 green indication lamps will light up simultaneously.
This function is automatically disabled after 24 hours. To deactivate
it earlier:
- Press the “Temperature setting” button again - the
temperature selection lights will return to the 1
st
temperature
level
Temperature selection
- It is possible to select the fridge/freezer
temperature from among 5 levels (level 1, level 2, level 3, level 4,
level 5) by pressing the temperature selection button .
Stand-by Mode / Cooling Off Mode.
It allows the User to turn ON or stand-by the product.
This function is enable even if any alarm or failure appears.
•ON state: when the product is in the Stand-by state and “turn
ON” press & keep pushbutton “stand-by” by 3s
• The product is turned ON;
• all functions should be enabled
• STAND-BY state: when the product is in the ON and the user
press pushbutton and keep by 3s “stand-by” to OFF appliance
• The appliance goes to STAND-BY when the user press and keep
pushbutton “stand-by” by 3 s
• The product is turned OFF, disabling all loads
• All function shall be disable;
• All lamps should be turned OFF;
• Turn off light.
Notes:
When the user press at once “Stand-by” and “Temperature setting”
to check indication of the alarms (displayed by lamp 1 & lamp 2 &
lamp 3) “Stand-by” function is locked.
“Black-out” Alarm (power supply failure) - in case of power
failure, the appliance automatically monitors the temperature
changes in the freezer compartment. After the power supply
returns,- the “Black-out” alarm will activate, if the temperature has
risen above the admissible level. This is indicated by:
- Flashing of the green indicator lamp (4, 5, 6).
- Activation of a beep.
When the “Black-out” alarm is active, it is recommended to
proceed as follows:
- If the food in the freezer is not frozen but is still cold, transfer it
promptly to the refrigerator compartment and consume within 24
hours.
- If the food in the freezer is frozen, it has re-frozen after thawing
caused by the power failure. The consumption of re-frozen food is
not recommended because it lost its nutritive value and may be
hazardous to your health.
Note: The “Black-out” alarm does not guarantee the food quality
and its safety in case of consumption. It only informs about the
necessity to assess the quality of food in the freezer and refrigerator
compartments. To deactivate the alarm, press the and hold
pushbutton “Temperature setting” & party mode button and
keep pressed for, until the indicator light goes off.
- The temperature will return to the normal operating cycle level
and the beep will silence.
Other abnormal appliance operations displayed by indicator lamps.
In case of abnormal appliance operation, all the temperature selection indicator lamps will flash and a beep will sound. After pressing and
holding the “Temperature setting” & “stand-by” mode (“reset alarm”) button, the beep will stop and the indicator lamps will light up,
showing the alarm code (possible alarm codes are explained in the table below).
After the (“reset alarm”) is released, the indicator lamps will flash until the fault is eliminated. If any alarm shown in the table occurs, the
fridge/freezer functions such as temperature adjustment and party modeare not available until the fault is eliminated.
When several alarms occur simultaneously, the alarm with the highest priority is displayed (with code 01 being the highest priority)
After determining the alarm code (between 01 and 05)
• The user can eliminate the reason of the code 04 alarm by closing the door completely.
• Code 05 alarm - The alarm deactivates when the minimum required temperature is reached.
• The other alarms (code 01, 02, 03) - Contact the After-Sales Service and provide the alarm code.
Alarm priority
Codification to be displayed by the Temperature Range Lamps
Lamp 1 Lamp 2 Lamp 3
FC Evaporator Temperature Sensor Alarm 01 OFF OFF ON
RC Evaporator Temperature Sensor Alarm 02 OFF ON OFF
RC Ambient Temperature Sensor Alarm 03 ON OFF OFF
Door Alarm 04 OFF OFF OFF
B.O.A 05 -- -
