Trane ZUSTATALP510 Manual Manual

Brand: Trane

Model: ZUSTATALP510

Category: Thermostats

Type: Manual Manual

Trane ZUSTATALP510 is a digital thermostat with advanced capabilities for precise temperature control and energy efficiency. With its intuitive interface and the ability to program setbacks for different times and days, you can optimize your indoor comfort and utility bills. The thermostat offers multiple operational modes, including cool, heat, auto, emergency heat, and off, providing flexibility for all seasons. It also allows you to monitor outdoor temperature and adjust fan operation for continuous or automatic circulation.

HOME

COMFORT

SENSOR

TRANE

6200 Troup Highway

Tyler, TX 75707

An American Standard Company

Pub. No. 22-5190-02

ZUSTATALP510

15345 ZUSTATALP51Ø Manual 2/28/05 8:15 AM Page 1

TABLE O

CONTENTS

1 ............................................................................. Introduction

2 – 3....................................................................... Getting Started

4 – 8....................................................................... Basic Procedures

9 – 10..................................................................... Setback Programming

11 ........................................................................... Copying

12 ........................................................................... Overrides

13 – 16................................................................... System Set-Up

17 – 20................................................................... Other Features

21 ........................................................................... Factory Settings and Specifications

22 ........................................................................... Index

Page

15345 ZUSTATALP51Ø Manual 2/28/05 8:15 AM Page 2

INTRODUCTION

How do we know?

Well, for one thing you just bought a Trane

Home Comfort Sensor, the communications inter-

face for the Trane Integrated Comfort System.

This means you’ve opted for energy efficiency,

lower utility bills and doing a little something to

save the planet–all in one bold move.

As you know, this is an instruction manual for

the Home Comfort Sensor.

Even the most intuitive trailblazers need

a road map sometimes, so this manual was

designed to be as self-explanatory

as possible.

The Home Comfort Sensor is a computer,

but that’s the last time we’ll mention it. These

instructions are in plain English with only a

couple of unusual words like setpoint and set-

back. No technical talk, no complicated diagrams.

All you have to do to become a Home Comfort

Sensor expert is follow the simple steps in this

booklet.

But before we begin, you might want to spend

a few moments looking over the glossary of terms

on the next page. It will make those unusual

words we mentioned earlier more meaningful.

You’re a very bright person.

15345 ZUSTATALP51Ø Manual 2/28/05 8:15 AM Page 3

GETTING

STARTED

You can start by pushing the right buttons.

Adjusts settings in various modes;

pressed once, they reveal current

setpoints; pressed more than once

they temporarily adjust temperature

settings.

Permits you to override scheduled

setpoints in order to schedule

temporary temperature adjustments.

Initiates setback scheduling.

Programs setback time and

temperature setpoints.

Selects operational modes: cool,

heat, auto, emergency heat & off.

Toggles between automatic or

continuous fan operation.

Displays outside temperature.

Initiates setting the clock and day.

Returns normal display to the Liquid

Crystal Display (LCD).

Note: The flashing green light in the

lower right corner indicates your sensor

is communicating with the system.

How To Bring The Home Comfort Sensor To Life.

Day/Clock

Exit

Fan

Hold Set

Point

Outdoor

Temp

Period

Time/Temp

Heat/Cool

15345 ZUSTATALP51Ø Manual 2/28/05 8:15 AM Page 4

For one thing, it can take a load off your

mind. Once you’ve set a schedule on the

Home Comfort Sensor, it will maintain comfort

control for you. Energy efficiency and lower

utility bills are now the Home Comfort Sensor’s

job, not yours. The thermostat will adjust when

it’s supposed to, and it won’t forget, as a mere

mortal might.

It will remember what you tell it, even during

emergencies. You’ll be happy to know that –

unlike your VCR and other electronic digital

clocks – the Home Comfort Sensor won’t

forget its programs during a power failure.

You have plenty of other things to worry about

when that happens. You probably won’t find

the instruction manual by then anyway, so

that’s why we’ve included three button batteries

for power backup. Simply install them and don’t

worry about a power failure knocking out your

Home Comfort Sensor thermostat. When the

LCD clock flashes, it’s time to replace your

batteries. But even when you have to change

your batteries, your Home Comfort Sensor

won’t forget its schedule.

The Home Comfort Sensor will stay in

touch with you and your home comfort system.

A little green light will flash to let you know

it’s talking with the heat pump or air conditioner.

That’s good. The last thing you want is a sense-

less sensor.

What The Home Comfort Sensor Can Do For You:

15345 ZUSTATALP51Ø Manual 2/28/05 8:15 AM Page 5

BASIC

PROCEDURES

Scheduling begins with four simple steps:

1. Remove the front of the Master Scheduler

from its mounting bracket. On the back side

you’ll see the batteries on the left edge.

Remove the plastic insulating strip from

between the batteries.

2. Replace the Master Scheduler to its

mounting bracket.

3. Read on.

Ready, Set…Relax.

15345 ZUSTATALP51Ø Manual 2/28/05 8:15 AM Page 6

BASIC

PROCEDURES:

LOCK

HOW DO I MAKE IT STOP FLASHING?

Answer: Tell the Home Comfort Sensor

what time it is.

TIME, PLEASE?

DAY/CLOCK triggers the Set Time mode.

It also hides everything else on the LCD

so you can focus on the job at hand.

Keep pressing DAY/CLOCK. Whatever

flashes – digits or words – may be set

with the UP or DOWN ARROW keys.

Settings go in the following order:

hours, minutes, days. But you’ve

probably already figured that out.

The clock is preset to display standard

time. If you prefer a 24-hour clock

(military time), see page 14.

EXIT locks in the correct time and day,

as well as returns normal display to

the LCD.

Your First Question Is Probably Going To Be:

Day/Clock

Exit

Set Time

Mon

15345 ZUSTATALP51Ø Manual 2/28/05 8:15 AM Page 7

BASIC

PROCEDURES:

ODE

Depends on the season, right?

HEAT/COOL sets the mode, just as the

flip switch did on your old thermostat.

But HEAT/COOL gives you more options.

As you press HEAT/COOL,

the LCD offers

• Cool

• Heat

• Auto – the Home Comfort

Sensor decides which mode,

cooling or heating, is needed

to maintain the setpoint; an

excellent feature for in

between

seasons when days are warm

and nights are chilly.

• Emergency Heat (Emerg Ht) –

directs the auxiliary heat source

to kick in (if your system has one).

The compressor won’t run in

this mode.

• Off

What Makes You Comfortable?

Heat/Cool

Wed

Cool

Return

Wed

Heat

Return

15345 ZUSTATALP51Ø Manual 2/28/05 8:15 AM Page 8

BASIC

PROCEDURES:

FAN toggles between:

• Fan On – the fan runs

continuously; on variable speed

systems the blower will run at

50% speed when the compressor

isn’t running.

• Automatic – the fan runs only

when the compressor is on.

Fan On is displayed when the fan is in

continuous operation.

The fan setting can be set for each schedule

period on any zone. This means you can

program the fan to run at any time to

improve the indoor air quality.

How’s Your Circulation?

Fan

Sat

Cool

Away

Sat

Cool

Fan On

Away

Fan

15345 ZUSTATALP51Ø Manual 2/28/05 8:15 AM Page 9

BASIC

PROCEDURES:

EMPERATURE

•To check the outdoor temperature,

press OUTDOOR TEMP. The outdoor

temperature ranges from -20°F to

120°F. (Note: If the outdoor sensor

is not installed, the outdoor tempera-

ture displayed on the thermostat will

be -13°F or below) Press OUTDOOR

TEMP again or EXIT to return to the

normal LCD display. Or wait a minute,

and the normal LCD display will return

on its own.

•Setpoints are the heating and cooling

temperatures you prefer. Press either

ARROW once to see the setpoint of the

current mode (cooling or heating). They

are displayed by the set of flashing

numbers on the left, next to the words

Set Pt. The actual indoor temperature

is indicated on the right. Press the

HEAT/COOL button to toggle between

heating and cooling setpoints. Press

EXIT when you’ve seen enough.

To change setpoints temporarily, see

pages 10 – 12.

A Matter Of Degrees.

Outdoor

Temp

Heat/Cool

Exit

Outdoor Temp

Set Pt

15345 ZUSTATALP51Ø Manual 2/28/05 8:15 AM Page 10

SETBACK

PROGRAMMING:

CHEDULING

ow For The Home Comfort Sensor’s Reason For Being.

Setback scheduling. What’s that, you say?

Setback means different temperature set-

points for different times and days. It’s why you

bought the Home Comfort Sensor, right? And it’s a

feature you’ll love, especially when you begin to

notice the savings on your utility bills.

•Press PERIOD to start scheduling.

(The word Schedule will light up.)

The four setback periods will be dis-

played in sequence when you continue

to press PERIOD. An arrow marks the

current setback period. You’ll also

see the time and temperature

corresponding to each period.

Naturally, the Home Comfort Sensor will

accept whatever time you enter into each

of the setback periods.

•Press DAY/CLOCK to select the day you

wish to program.

•Press TIME/TEMP until the hours flash,

then press either ARROW to reach or

change the hour you want to initiate

this setpoint. Press TIME/TEMP again

to adjust the minutes in 10-minute

intervals.The bars at the bottom of

the display will graphically show the

relationship between this period and

adjacent periods.

Note: There is no need to program a “stop” time.

(This is determined by the “start” time of the next

time period.)

SCHEDULE

CoolHeat

NoonMidnt Midnt

Wake Away Return Sleep

Mon

SCHEDULE

CoolHeat

NoonMidnt Midnt

Mon

Wake Away Return Sleep

Day/Clock

Period

Time/Temp

15345 ZUSTATALP51Ø Manual 2/28/05 8:15 AM Page 11

SETBACK

PROGRAMMING:

CHEDULING

•Press TIME/TEMP again to reach

or change the Heat setpoint;

set it with the ARROWS. Follow

the same procedure for your

Cool setpoint.

Note: The cooling setpoint will always be

at least four degrees higher than the heating

setpoint. If one setpoint infringes on the required

four-degree separation, the Home Comfort Sensor

will automatically adjust the other to maintain

the difference.

•Press FAN to toggle the fan mode.

FAN ON is displayed when the fan

is in continuous operation.

•Press PERIOD to advance to the next

setback period. EXIT will return the LCD’s

normal display once you’ve scheduled

all setpoints.

Congratulations! You’ve mastered the most

important element of your Home Comfort Sensor.

Ready to move on?

SCHEDULE

CoolHeat

NoonMidnt Midnt

Wake Away Return Sleep

Mon

SCHEDULE

Heat

NoonMidnt Midnt

Cool

Fan On

Wake Away Return Sleep

Mon

Period

Time/Temp

Exit

Fan

Period

15345 ZUSTATALP51Ø Manual 2/28/05 8:15 AM Page 12

SETBACK

PROGRAMMING:

OPYING

• The PERIOD button gets you into the

setback program for a specific day.

Press this button.

• This is where the COPY button can save

some time, particularly with a zoned

system. Let’s assume that you want to

utilize the same time and temperature

values for the entire week that you have

already programmed for this day.

All you need to do is depress the COPY

button and select any day or all seven

days with the DAY/CLOCK button.

Depress the COPY button again

and it is done.

This process allows you to copy one day

to all other days or any specific day.

Press EXIT to return the LCD to the

normal display.

Exit

Period

Copy

15345 ZUSTATALP51Ø Manual 2/28/05 8:15 AM Page 13

OVERRIDES

Maybe you’re mostly happy with your new

schedule, but right now you wish the temperature

were different. There’s a way to temporarily over-

ride your scheduled setpoints until the next set-

back period rolls around or until you change your

mind again, whichever comes first.

•Press either ARROW, and you’ll see

the current setpoint on the left side of

the LCD (next to Set Point).

The current indoor temperature is to

the right.

•Press the appropriate ARROW to

change the setpoint temperature.

Temporary will now be displayed to

indicate you’ve changed the set point

from your original selection.

•Press EXIT once you have reached your

temporary setpoint or schedule and

wish to return to the LCD’s normal

display. Notice that Temporary is

now flashing.

•Press EXIT again to cancel the

temporary setpoint and return to

the scheduled setpoint.

•Remember, when you lower the

cooling setpoint or increase the heating

setpoint, the Home Comfort Sensor will

automatically adjust the opposite set-

point to maintain the required four-

degree difference.

Change Can Do A Body Good.

Exit

Cool

Set Pt

Tue

Cool

Away

Temporary

Exit

15345 ZUSTATALP51Ø Manual 2/28/05 8:15 AM Page 14

SYSTEM

SET-UP

Say you’re going on vacation. Maybe you

have picky houseguests. Or you’re keeping

unusual hours. For whatever reason, you want

the Home Comfort Sensor to maintain a constant

temperature, but you don’t want to reschedule

all the setback temperatures you entered earlier.

Here’s how to HOLD that constant temperature.

•Press either ARROW to display

and change the setpoint to a new

temperature. Then press HOLD SET

POINT to lock in your new selection.

That’s where it will stay until you

tell it otherwise.

•Press EXIT to return to the LCD to

its normal display. HOLD should

now be blinking.

•To cancel HOLD and return to your

original schedule, press EXIT or

HOLD SET POINT.

Hold that Temperature.

Hold Set

Point

Hold Set

Point

Exit

Cool

Temporary

Set Pt

Tue

Cool

Hold

Away

Hold Set

Point

15345 ZUSTATALP51Ø Manual 2/28/05 8:15 AM Page 15

SYSTEM

SET-UP

Let’s say you prefer military time on your

LCD clock. Or you’d rather see the temperature

in Celsius degrees. Or you think the temperature

reading needs adjusting. Or you just feel like

going beyond the basics.

•While holding down EXIT, press

OUTDOOR TEMP. Hold both keys

simultaneously until System Set-Up

appears in the upper left corner of

the LCD. (This will take approximately

three seconds.)

Now the Home Comfort Sensor will begin to

talk to you. Watch for messages where the clock

is normally displayed.

•The first Set-Up is the time format. If

you operate on a 24-hour clock and you

don’t have to think twice to remember

that 1500 hours means 3:00 p.m., this

one’s for you. When the letters hr

appear, press either ARROW to toggle

between 12 and 24 to choose the

number of hours on your clock.

Getting Really Fancy.

Exit

Outdoor

Temp

SYSTEM SET-UP

15345 ZUSTATALP51Ø Manual 2/28/05 8:15 AM Page 16

SYSTEM

SET-UP

•Press HEAT/COOL to initiate the next

Set-Up which enables you to change

from Fahrenheit to Celsius. When the

word Temp comes up under the clock,

press the ARROW keys to choose

between F and C.

•Press HEAT/COOL again and you’ll

see Addr for the zone address. The

only reason to adjust this Set-Up is

if your home has more than one

heating/cooling zone.

Most Home Comfort Sensors control only

one zone anyway, so leave this one on the

factory setting (01). If you have more than

one zone, this is an adjustment best left to

technicians.

Heat/Cool

Here’s something you need to know:

When you change this setting, all of the set-

points and setbacks you scheduled so carefully

will revert to factory settings. You may also

lose factory calibrations.

SYSTEM SET-UP

Heat/Cool

15345 ZUSTATALP51Ø Manual 2/28/05 8:15 AM Page 17

SYSTEM

SET-UP

•Press HEAT/COOL again for the fourth

Set-Up which is indoor temperature

calibration. This is best left to profes-

sionals. But if

you

and your independent

thermometer say the Home Comfort

Sensor is off and you really want to

change it yourself, use the ARROW

keys to change the calibration of the

indoor temperature sensor. You’re in this

mode when the letters CAL appear.

•Press EXIT to return to normal

operations.

You have now completed the set-up and

scheduling of your Home Comfort Sensor. Replace

the unit to its mounting bracket. When the word

“connect” disappears, your Trane Integrated

Comfort System is ready for operation.

Exit

SYSTEM SET-UP

Heat/Cool

15345 ZUSTATALP51Ø Manual 2/28/05 8:15 AM Page 18

OTHER

FEATURES

•The speed bar (System Speed %) along

the bottom of the LCD tells you at what

capacity and speed your compressor is

operating. The lowest operating speed is

50 percent.

•Aux Ht (auxiliary heat) lights up when any

kind of supplemental heating kicks in.

•Service lights up as a cry for attention.

Refer to the Troubleshooting section.

Other Things That May Come Up.

SERVICE

Wed

Cool

Aux Ht

Away

System Speed %

0 100

15345 ZUSTATALP51Ø Manual 2/28/05 8:15 AM Page 19

OTHER

FEATURES

•If you’re planning to connect the Home

Comfort Sensor to a home automation

system, this equipment may override

the Home Comfort Sensor scheduling

capabilities. Some of what you’ve

learned so far may not apply if the

home automation system overrides

the thermostat functions.

15345 ZUSTATALP51Ø Manual 2/28/05 8:15 AM Page 20

Page is loading ...

Trane ZUSTATALP510 Manual Manual

Brand: Trane

Model: ZUSTATALP510

Category: Thermostats

Type: Manual Manual

Download PDF

report

Trane ZUSTATALP510 Manual Manual

Trane ZUSTATALP510 Manual Manual

Related papers

Other documents