Grace Company Little Gracie II Operating instructions

Brand: Grace Company

Model: Little Gracie II

Type: Operating instructions

This manual is also suitable for

The Little Gracie II

The New Little Gracie II

Home Machine Quilting System

Parts List

Part List A ........................................................................................................2

Part List B ........................................................................................................3

Part List C ........................................................................................................4

Care of Your Frame ..........................................................................................5

Assembly Steps:

Step 1: Take Up Rail Mount End Assembly ...................................................7

Step 2: Fabric Layer Rail Mount End Assembly ............................................8

Step 3: Rail Mount End Assembly ..................................................................9

Step 4: Frame End Hardware Assembly .........................................................10

Step 5: Frame End Assembly ..........................................................................11

Step 6: Side Leg Brace “B” Assembly ............................................................11

Step 7: Side Leg Brace “A” Assembly ...........................................................12

Step 8: Legs to Frame End Assembly .............................................................13

Step 9: Table Assembly ...................................................................................14

Step 10: Middle Leg Spacer Assembly ...........................................................15

Step 11: Track Installation ..............................................................................16

Step 12: Frame End to Table Assembly ..........................................................16

Step 13: Middle Leg Installation .....................................................................17

Step 14: Middle Leg Assembly .......................................................................18

Step 15: Rail Assembly ...................................................................................19

Step 16: Rails to Frame Assembly....................................................................20

Step 17: Ratchet Stop Assembly .....................................................................22

Step 18: Carriage Stop Assembly ...................................................................22

Optional 4th Pole .............................................................................................23

Fabric Installation ..........................................................................................24

Making Cloth Leaders ......................................................................................25

Installing Your Fabric Layers to the Rails .......................................................26

Step 1: Quilt Backing to Second Rail .............................................................26

Step 2: Quilt Top to 3rd Rail ...........................................................................26

Step 3: Batting.................................................................................................26

Step 4: Attaching Layers to the Take-Up Rail ................................................27

Step 5: Putting Your Machine/ Carriages Onto Frame ...................................27

Rolling Your Fabric ..........................................................................................28

The Four-Inch Principle ...................................................................................28

Bungee Clamp Assembly .................................................................................28

Jim M. Bagley, GraceWood, Inc

(Reproduction Prohibited)

Printed Date 02-01-10

Little Gracie II

Parts List A

(1) Left Rail Mount End

(1) Right Rail Mount End

(1) Left Frame Side

(1) Right Frame Side

(1) Right Take

Up Rail

Mount End

(1) Left Take

Up Rail

Mount End

(1) Left Fabric

Layers Rail

Mount End

(1) Right Fabric

Layers Rail

Mount End

(1) Table #1

(1) Table #2

(1) Table #3

(2) Carriage

Stop Base

(2) Carriage

Stop Clamp

(1) Left

Front Leg

(1) Right

Front Leg

(1) Right

Back Leg

(1) Left

Back Leg

(2) Middle

Leg "A"

(2) Middle

Leg "B"

Little Gracie II

Parts List B

(2) Middle Leg Brace

(2) Middle

Leg Spacer

(2) Track

Support Splice

(3) 64" Crib Rail

(3) 34" Queen Rail

(3) Ratchet

Wheel

(3) Square

End Cap

(6) End Cap

Shoulder

(3) Round

End Cap

(3) Ratchet

Stop

(1) Back Crib Table Aluminum Track Support

(1) Front Crib Table Aluminum Track Support

(1) Back Queen Table Aluminum Track Support

(1) Front Queen Table Aluminum Track Support

(3) Fabrifast Tubing

(4) Bungee

Clamp

(2) 65-1/2" Plastic Track

(2) 99-1/2" Plastic Track

(2) Side Leg

Brace " A"

(2) Side Leg

Brace " B"

(3) Rail Coupler

-Pre-Installed in your 64” rail

-Pre-Installed in your Crib Table Aluminum Track Supports

Little Gracie II

Parts List C

(20) 1/4" X 1-1/2"

Carriage Bolt

(15 ) 1/4" X 45mm

Connector Bolt

(26 ) 1/4" X 3/4" Phillips

Pan Head Screw

(8) 1/4" X 2" Phillips

Pan Head Screw

(8) 1/4" X 1" Phillips

Pan Head Screw

(3) 1/4" X 1-1/2"

Truss Bolt

(6) #8 X 7/8"

Screw

(12) 1/4" Rectangle

Nut

(2) 1/4" X 2-1/4"

Carriage Bolt

(3 ) 1/4" X 35mm

Connector Bolt

(22 ) 1-1/4" Fender

Washer

(23 ) 1/4" Plastic

Knob

(1) 4mm Allen Wrench

(1) Fabri-fast Tool

(67 ) 3/16" Flat

Washer

(27 ) 1/4" Flat

Washer

(20 ) 1/4" Nylock

Nut

(57 ) 1/4" Jam

Nut

(8) M6 x 50mm Phillips

Pan Head Screw

(10) M6 x 35mm

Connector Bolt

(8) M6 x 45mm

Connector Bolt

(2) M6 x 55mm

Carriage Bolt

(6) M4 x 30mm

Screw

(20) M6 x 40mm

Carriage Bolt

(8) M6 x 25mm Phillips

Pan Head Screw

(3) M6 x 40mm

Truss Bolt

(36) M5 x 10mm

Socket Head Screw

(26) M6 x 20mm Phillips

Pan Head Screw

(8) M6 Rectangle Nut

(12) M6 Flat

Washer

(52) M5 Flat

Washer

(18) M5

Square Nut

(preinstalled)

(50) M6 Jam

Nut

(12) M6 Nylock

Nut

(18) M6 Plastic

Knob

(18) M8 Fender

Washer

(18) M5 x 16mm

Socket Head Screw

(1) 3mm Allen Wrench

(1) 4mm Allen Wrench

(1) Fabri-fast Tool

(1) Open End Wrench

10mm X 13mm

CARE OF YOUR LITTLE GRACIE II

Your Little Gracie II frame is a machine quilting system that can be used nished or unnished. Most

use it unnished with no problem, and doing so does not adversely affect warranty coverage. However, for

extra protection, or to give it a nished look, you may seal, stain and/or nish the frame using a number of

different applications. This is best done BEFORE YOU ASSEMBLE your frame.

To seal the wood, we recommend an application of tung oil or Danish Oil nish that will help preserve

the wood and will help to prevent warping. We recommend the McCloskey’s Tung Seal, Deft

or Watco

brands. Some prefer to use a urethane coat to add a more glossy nish.

Test stain on an inconspicuous place. Many different nishes and/or stains may be suitable for sealing

and beautifying your frame. You may want to consult your local paint retailer for nishes that are easy to apply

and dry hard–not oily.

Use and Storage Tip

--Store frame in a dry place.

If not assembled, store with braces in vertical position.

(This will prevent oor

moisture from seeping into the parts).

Five-Year Limited Warranty

GraceWood, Inc. will replace or repair, at our choosing, any part of the Little Gracie

Machine Quilting

System which may be shown to be defective. This warranty does not cover parts damaged through misuse,

improper storage, improper assembly, loss, natural events and willful or accidental destruction. Defective parts

may be returned only with a valid RMA# which may be obtained by calling GraceWood, Inc. at

1-800-264-0644 or 1-801-485-6688.

NOTE: Warranty card must be lled out, stamped and mailed to the address on the card within 30 days of

purchase.

Contact Information

For Technical Support or any other correspondence concerning your Little Gracie II, call 1-800-264-0644 ~

~ E-mail: [email protected] ~ OR ~ Fax: (801) 908-8888 ~

OR ~ Write to:

The Grace Company

P.O. Box 27823

Salt Lake City, UT 84127

For details on accessories and other information, see us online at www.graceframe.com

For shipping of materials to The Grace Company address package (postage prepaid) to: The Grace Company,

2225 South 3200 West, SLC, UT 84119. Materials may be returned only with a valid RMA# or Returned

Merchandise Authorization Number which may be obtained by calling GraceWood, Inc. at

1-800-264-0644.

If you call after business hours (M-F 8:00 a.m. – 5 p.m., MST) be assured that your call will be returned

the next business day if you leave a message. Please report any errors in these instructions or make comments

to the following: [email protected]

Grace Quilting Frames and Hoops: Innovation and Evolution

Grace Quilting Systems have been developed over the past two decades with several original design

innovations. Additionally, because of feedback from many of the thousands of quilters who have purchased

and use our machine quilting systems, we have been able to make a frame that will truly enhance the entire

process of machine quilting from beginning to end. If you have any suggestions that will help us to improve

our product or service, let us know, using one of the above contact methods.

WELCOME!

As you begin assembly of your new Little Gracie home machine quilting system, keep in the mind the

following:

1) Plan to spend a minimum of 2-4 hours in assembly. This process will be simple and step-by-step.

2) Read through each step completely before beginning that step.

3) Using the parts list as a reference, take the parts out of the box and make sure that you have them all. (If there

is something missing or broken, contact the Grace Company at 1-800-264-0644. Our ofces are open from 8:00 am-

5:00 pm MST Mon.-Fri. If calling after hours, you may leave your message and we will promptly ship any item

needed).

4) For your convenience, an “L” and “R” have been etched into the INSIDES of most pieces to help you distinguish

between left and right parts and inside and outside of parts.

5) Identify Hardware Packets: All hardware is separated by type and each packet is labeled for ease in identication

you will nd packets located in a rectangular box.

6) This is a new product! We welcome your feedback on this product or these instructions. If you encounter a

problem during assembly or use of the Little Gracie, and you can’t seem to overcome it, call us before frustration

sets in!

Tools Needed:

10mm Socket Wrench

Adjustable wrench

Phillips Screw Driver

Allen wrench (provided)

Fabri-Fast Tool (to be used when installing your fabric).

Left Take Up

Rail Mount End

1/4" X 1-1/2"

Carriage Bolt

3/16" Flat Washer

1/4" Jam Nut

3/16" Flat Washer

1/4" Jam Nut

1/4" X 1-1/2" Carriage Bolt

Right Take Up

Rail Mount End

Step 1: Take Up Rail Mount End Assembly

Parts Needed: 1- Right and Left Take Up Rail Mount End

4- M6 Jam Nut

4- M5 Flat Washer

4- M6 X 40mm Carriage Bolt

• Place one of the carriage bolts

through each of the holes on the Left

Take Up Rail Mount End, making sure

the head of the bolt is on the side with

the L.

Left Take Up Rail Mount End

Inside View

Right Take Up Rail Mount End

Inside View

HINT: Some holes in the wood pieces may be a

little tight for the hardware. If this is case, tap

in the hardware using the handle of your screw

driver.

• Place one washer and one jam nut on the end of the bolt.

• TIGHTEN JAM NUTS COMPLETELY ONTO EACH BOLT

• IMPORTANT: Completely tighten the jamb nut onto the bolt until the head of the bolt is pulled into the

counter-sunk hole.

• Repeat the above steps for the Right side.

M6 Jam Nut

M5 Flat Washer

M6 x 40mm

Carriage Bolt

M6 Jam Nut

M5 Flat Washer

M6 x 40mm Carriage Bolt

Left Fabric Layers

Rail Mount End

1/4" X 1-1/2"

Carriage Bolt

3/16" Flat Washer

1/4" Jam Nut

1/4" X 1-1/2"

Carriage Bolt

3/16" Flat Washer

1/4" Jam Nut

Right Fabric Layers

Rail Mount End

Step 2: Fabric Layers Rail Mount End Assembly

Parts Needed: 1- Right and Left Fabric Layer Rail Mount End

4- M6 Jam Nut

4- M5 Flat Washer

4- M6 X 40mm Carriage Bolt

Right Fabric Layers Rail Mount End

Inside View

Left Fabric Layers Rail Mount End

Inside View

• Place one of the carriage bolts through each of the holes on the Left Fabric Layer Rail Mount End, making sure

the head of the bolt is on the side with the L.

• Place one washer and one jam nut on the end of the bolt.

• IMPORTANT: Completely tighten the jamb nut onto the bolt until the head of the bolt is pulled into the

counter-sunk hole.

• Repeat the above steps for the Right side.

M6 x 40mm

Carriage Bolt

M5 Flat Washer

M6 Jam Nut

M5 Flat Washer

M6 x 40mm

Carriage Bolt

Left Rail Mount End

1-1/4" Fender Washer

1/4" Plastic Knob

1/4" Flat Washer

1/4" Nylock Nut

Right Rail Mount End

1-1/4" Fender Washer

1/4" Flat Washer

1/4" Nylock Nut

1/4" Plastic Knob

M6 Flat Washer

M8 Fender Washer

M6 Plastic Knob

M6 Nylock Nut

Step 3: Rail Mount End Assembly

Parts Needed: 1- Right and Left Take Up Rail Mount End

1- Right and Left Fabric Layer Rail Mount End

1- Right and Left Rail Mount Ends

4- M8 Fender Washer

4- M6 Plastic Knob

4- M6 Nylock Nut

4- M6 Flat Washer

• As shown in the drawing, place the bolts in the Right Take Up Rail Mount End through the rst slot on the Right

Rail Mount End.

• Place a fender washer followed by a plastic knob on the top bolt.

• Put a washer and then a nylock nut on the bottom bolt. NOTE!! Leave all the nylock nuts loose to allow the

washer to turn in your ngers!

• Follow the above steps for the Left Take Up Rail Mount End, Right Fabric Layer Rail Mount End, and the Left

Fabric Layer Rail Mount End.

Left Rail Mount End

Outside View

Right Rail Mount End

Outside View

• The nylon side of the nylock nut

faces out when threading it on the

bolt.

M6 Flat Washer

M6 Nylock Nut

M6 Plastic Knob

M8 Fender Washer

1/4" X 1-1/2"

Carriage Bolt

3/16" Flat Washer

1/4" Jam Nut

Right Frame End

1/4" X 1-1/2"

Carriage Bolt

3/16" Flat Washer

1/4" Jam Nut

Left Frame End

M5 Flat Washer

M6 Jam Nut

M6 x 40mm

Carriage Bolt

M6 x 40mm

Carriage Bolt

M5 Flat Washer

M6 Jam Nut

Step 4: Frame End Hardware Assembly

Parts Needed: 1- Right and Left Frame End

12- M6 X 40mm Carriage Bolt

12- M5 Flat Washer

12- M6 Jam Nuts

Right Frame End

Outside View

Left Frame End

Outside View

• Place one of the carriage bolts through each of the holes, except for the two on each end, on the Right Frame

End, making sure the head of the bolt is on the side with the R.

• Place one washer and one jam nut on the end of the bolt.

• REMINDER: Completely tighten the jamb nut onto the bolt until the head of the bolt is pulled into the counter-

sunk hole.

• Repeat the above steps for the right side.

1-1/4" Fender Washer

1/4" Plastic Knob

Right Frame End

Left Frame End

1-1/4" Fender Washer

1/4" Plastic Knob

Side Leg

Back Right

Side Leg

Brace "B"

1/4" Rectangle Nut

1/4" X 45mm

Connector Bolt

M8 Fender Washer

M6 Plastic Knob

M8 Fender Washer

M6 Plastic Knob

Step 5: Frame End Assembly

Parts Needed: 1- Right and Left Frame End

1- Right and Left Rail Mount End

4- M8 Fender Washer

4- M6 Plastic Knob

Right Frame End

Outside View

• Place the top two bolts on the Right Frame

End in the slots on the bottom of the Right

Rail Mount.

• Put a washer and then a plastic knob on

each of the bolts.

Left Frame End

Outside View

Step 6: Side Leg Brace “B” Assembly

Parts Needed: 2- Side Leg Brace “B”

1- Right Back Side Leg

1- Left Front Side Leg

2- M6 X 45mm Connector Bolt

2- M6 Rectangle Nut (threaded)

• Place a rectangle nut

vertically in the “t” slot of

the Side Leg Brace “B”, as

illustrated to the right.

• Follow the above steps again to complete the left side.

• The nylon side of the nylock nut faces out when

threading it on the bolt.

• NOTE!! Leave all the nylock nuts loose enough to

slide in the joint, and loose enough to allow the washer

to turn in your ngers!

• Connnect the Right Back Side Leg to the Side Leg

Brace “B” by threading the connector bolt through the

hole in the Right Back Side Leg and into the rectagle

nut. (Holding the rectagle nut in place, while using the

provided allen wrench to tighten the connector bolts.)

Back Right Side Leg

Inside View

M6 Rectangle Nut

M6 x 45mm

Connector Bolt

Side Leg

Front Right

Side Leg

Brace "A"

1/4" Rectangle Nut

1/4" X 45mm

Connector Bolt

Side Leg

Brace "B"

Side Leg Front Left

1/4" X 45mm

Connector Bolt

1/4" Rectangle Nut

Side Leg

Back Left

Side Leg

Brace "A"

1/4" X 45mm

Connector Bolt

1/4" Rectangle Nut

• Place a rectangle nut vertically in the “t” slot of the Side Leg

Brace “A”, as illustrated to the left.

• Connnect the Right Front Side Leg to the Side Leg Brace

“A” by threading the connector bolt through the hole in the

Right Front Side Leg and into the rectagle nut. (Holding the

rectagle nut in place, while using the provided allen wrench to

tighten the connector bolts.)

• Complete the above steps again to complete the Left Back

Side Leg.

Step 7: Side Leg Brace “A” Assembly

Parts Needed: 2- Side Leg Brace “A”

1- Right Front Side Leg

1- Left Back Side Leg

2- M6 X 45mm Connector Bolt

2- M6 Rectangle Nut (threaded)

Front Left Side Leg

Outside View • Complete the above steps again to complete the

Left Front Side Leg.

Front Right Side Leg

Inside View

Back Left Side Leg

Outside View

M6 Rectangle Nut

M6 x 45mm

Connector Bolt

M6 x 45mm

Connector Bolt

M6 Rectangle Nut

M6 x 45mm

Connector Bolt

1-1/4" Fender Washer

1/4" Flat Washer

1/4" Nylock Nut

1/4" Plastic Knob

1-1/4" Fender Washer

1/4" Plastic Knob

1/4" Flat Washer

1/4" Nylock Nut

Left Frame End

Outside View

• Place a fender washer on the top bolt, and then thread and tighten

the plastic knob onto the bolt.

• Place the at washer on the bottom bolt, and then tighten the

nylock nut.

• Make sure nylock nuts are loose enough to allow the washer to turn

in your ngers.

• Follow the above steps to complete the left side.

• The nylon side of the nylock nut faces out when threading it on

the bolt.

• NOTE!! Leave all the nylock nuts loose enough to slide in the

joint, and loose enough to allow the washer to turn in your ngers!

Right Frame End

Outside View

• Put the Right Front Side Leg on the pre-

installed bolts on the Right Frame End (below

the Fabric Layer Rail Mount End).

• Place a fender washer on the top bolt, and

then thread and tighten the plastic knob onto

the bolt.

• Place the at washer on the bottom bolt,

and then tighten the nylock nut.

• Make sure nylock nuts are loose enough to

allow the washer to turn in your ngers.

• Put the Right Back Side Leg on the pre-

installed bolts on the Right Frame End (below

the Take Up Rail Mount End).

Step 8: Legs to Frame End Assembly

Parts Needed: 1- Right and Left Frame End

1- Right and Left Front Side Leg

1- Right and Left Back Side Leg

4- M6 Nylock Nut

4- M6 Flat Washer

4- M8 Fender Washer

4- M6 Plastic Knob

M8 Fender Washer

M6 Flat Washer

M6 Plastic Knob

M8 Fender Washer

M6 Nylock Nut

M6 Flat Washer

1/4" X 3/4" Phillips

Pan Head Screw

3/16" Flat Washer

1/4" Jam Nut

1/4" X 3/4" Phillips

Pan Head Screw

3/16" Flat Washer

1/4" Jam Nut

Front Crib Table

Aluminum Track Support

Crib Table #2

Crib Table #1

Back Crib Table

Aluminum Track Support

• Place the Tabe #1 on the front crib table aluminum track support (as pictured above). ** You might want to stand

the table on it’s side to make it easier to tighten the nuts.**

• Put a phillips pan head screw through the middle hole on the Table #1 through the front crib table aluminum

track support, and then on the end of the phillips pan head screw put a at washer followed by a jam nut.

• Put a phillips pan head screw through the other two holes on the Table #1, and then put a at washer followed

by a jam nut on each end.

• Follow the above steps to attach the front crib table aluminum track support to the Table #2.

• Follow the above steps to attach the back crib table aluminum track support to the Table #1 and #2.

• Place the Table #3 on the front queen table aluminum track support (as pictured left).

Step 9: Table Assembly

Parts Needed: 1- Table #1

1- Table #2

1*- Table #3

1- Front Crib and *Queen Table Aluminum Track Support

1- Back Crib and *Queen Table Aluminum Track Support

12 or 18*- M6 X 20mm Phillips Pan Head Screw

12 or 18*- M5 Flat Washer

12 or 18*- M6 Jam Nut

* Queen assembly ONLY

• Put a phillips pan head screw through the middle hole on

the Table #3 through the front queen table aluminum track

support, and then on the end of the phillips pan head screw

put a at washer followed by a jamb nut.

• Put a phillips pan head screw through the other two holes on

the Table #3, and then put a at washer followed by a jam nut

on each end.

•IMPORTANT! Carefully identify your Front and Back

Crib Track Supports based on the position of the holes.

NOTE: The Crib Back Track Support mounts to the

“slotted” side of the table.

M6 X 20mm Phillips

Pan Head Screw

M5 Flat Washer

M6 Jam Nut

M6 X 20mm Phillips

Pan Head Screw

M6 Jam Nut

M5 Flat Washer

1/4" X 2" Phillips

Pan Head Screw

3/16" Flat Washer

1/4" Jam Nut

Table Splice

1/4" X 3/4" Phillips

Pan Head Screw

1/4" X 2" Phillips

Pan Head Screw

Middle Leg Spacer

3/16" Flat Washer

1/4" Jam Nut

• The M6 X 20mm phillips pan head screws will go through

the end two holes with a washer and jam nut on the end.

• Follow the above steps for the other side

Step 10: Middle Leg Spacer Assembly

Parts Needed: 1- Crib Table (assembled)

1*- Queen Table (assembled)

2- Middle Leg Spacer

2*- Table Splice

4 or 8*- M6 X 50mm Phillips Pan Head Screw

4*- M6 X 20mm Phillips Pan Head Screw

4 or 12*- M5 Flat Washer

4 or 12*- M6 Jam Nut

• You will not want to completely tighten the nuts on this

step until you have completed track installation in step

11. Your tracks will go in easier if the bolt is not tight.

• Place the at side of the Middle Leg Spacer

against the front crib table aluminum track support

(as show above, and to the left).

• Put a phillips pan head screw through the left hole following the same steps as you did for the right.

• Follow the above steps to attach the Middle Leg Spacer to the back crib table aluminum track support.

• Place your Crib Table #2 next to you Queen Table #3.

• Where your Crib Table meets your Queen table you will

place a Table Splice (at end against the aluminum track

support).

• You will place a M6 X 50mm phillips pan head screw

through the center two holes in the aluminum track support

and then through the Table Splice. A washer and jam nut will

go on the end of the screws.

• You will place a M6 X 50mm phillips pan

head screw through the center two holes

in the aluminum track support and then

through the Table Splice. A washer and jam

nut will go on the end of the screws.

• Put one phillips pan head screw through the

right most hole in the front crib table aluminum

track support, which will then go through the

Middle Leg Spacer.

• You will then put a at washer on the end of

the screw, which will be followed by a jam nut.

M6 X 20mm Phillips

Pan Head Screw

M6 X 50mm Phillips

Pan Head Screw

M6 X 50mm Phillips

Pan Head Screw

M5 Flat Washer

M6 Jam Nut

M5 Flat Washer

99-1/2" Queen

Plastic Track

1/4" X 3/4" Phillips

Pan Head Screw

1/4" X 1" Phillips

Pan Head Screw

65-1/2" Crib Plastic Track

Step 11: Track Installation

Crib Parts Needed: 2- 65-1/2” Plastic Track

1- Crib Table (assembled)

Queen Parts Needed: 2- 99-1/2” Plastic Track

1- Queen Table (assembled)

• Snap one of the plastic track (“V” SIDE DOWN) into the front table aluminum track support.

• Snap the last plastic track (“V” SIDE DOWN) into the back table aluminum track support.

Step 12: Frame End to Table Assembly

Parts Needed: 1- Right and Left Frame End

1- Table (crib or queen)

8- M6 X 25mm Phillips Pan Head Screw

4-M6 X 20mm Phillips Pan Head Screw

• Place your Left Frame End on the left side of your table (Table #1). It

is recommended that you prop the right side of the table on something so

you can put the left side on rst.

• The two holes on the back of your Left Frame End is where the M6

X 25mm phillips pan head screw go through to screw into the aluminum

track support.

**CRIB TRACK is

preinstalled in your

Crib Track Support

pieces.

NOTE: You have been provided plastic track for both possible frame sizes so that you will never have more than 1

piece of track in each track support. Seamless track ensures smooth sewing machine movement.

Installed Track

M6 X 20mm Phillips

Pan Head Screw

M6 X 25mm Phillips

Pan Head Screw

NOTE: This illustration shows the Middle Leg

Brace assembled to the Middle Legs. Do this

AFTER you have installed you Middle Legs to

the frame (Step 14).

Instructions continued from previous page

• The M6 X 20mm phillips pan head screw goes through the

aluminum track support to the Side Leg Brace. (as illustrated left).

• Two of the M6 X 25mm phillips pan head screw go through the

front Left Frame End to screw into the aluminum track support,

similar to what you just did on the back.

• Follow the above instructions to attach your Right Frame End

to your table, except the Left Frame End can hold up your table.

Step 14: Middle Leg Installation

Parts Needed: 1 or 2*- Middle Leg (assembled)

2 or 4*- M6 Plastic Knob

2 or 4*- M8 Fender Washer

2 or 4*- M6 Nylock Nut

2 or 4*- M6 Flat Washer

*Queen Assembly ONLY

• Lay the Little Graice on it’s side with

the front down, as illustrated.

• Put the “B” side of your Middle Leg

on the bolts, which are on the front of

your frame.

1/4" X 3/4" Phillips

Pan Head Screw

1/4" X 1" Phillips

Pan Head Screw

M6 X 20mm Phillips

Pan Head Screw

M6 X 25mm Phillips

Pan Head Screw

1/4" X 45mm

Connector Bolt

1/4" Rectangle Nut

Middle Leg "A"

Middle Leg "B"

Step 13: Middle Leg Assembly

Parts Needed: 1 or 2*- “A” Middle Leg

1 or 2*- “B” Middle Leg

1 or 2*- Middle Leg Brace

2 or 4*- M6 X 45mm Connector Bolt

2 or 4*- M6 Rectangle Nut (threaded)

* Queen set up ONLY

• Connect the “A” and “B” Middle legs by placing the

connector bolts through each leg hole as pictured, and into

the Middle Leg Brace.

• Place a rectangle nut in the Middle Leg Brace so the

connector bolt can be screwed into the nut tight.

• NOTE if you are setting up for queen, you will assembly

two sets of legs.

M6 Rectangle Nut

M6 X 45mm

Connector Bolt

1-1/4" Fender Washer

1/4" Plastic Knob

1/4" Flat Washer

1/4" Nylock Nut

• On the other bolt you will put a fender washer and then a plastic knob.

• The right side is just opposite of the above instructions. The illustration on the previous page will help.

• Lay the Little Graice on it’s side with the front

down, as illustrated.

• Put the “B” side of your Middle Leg on the bolts,

which are on the front of your frame.

• The bolt to the right of the “B” is where you will

put a at washer followed by a nylock nut.

• On the other bolt you will put a fender washer

and then a plastic knob.

• You will have to push the “A” Side down enough to get it on the bolts on the back side of your frame.

• The right side is just opposite of the above instructions. The illustration on the previous page will help.

M6 Flat Washer

M6 Nylock Nut

M6 Plastic Knob

M8 Fender Washer

1/4" Plastic Knob

1/4" Nylock Nut

1/4" Flat Washer

1-1/4" Fender

Washer

• You will have to push

the “A” Side down

enough to get it on the

bolts on the back side of

your frame.

• It is okay to tap the

leg into place with your

hand, it will be a tight t

when you start

• The bolt to the right of

the “B” is where you will

put a at washer followed

by a nylock nut.

M6 Plastic Knob

M6 Flat Washer

M8 Fender

Washer

M6 Nylock Nut

Crib Size Rail

64” Rail

M5 X 16mm Socket

Head Screw

Step 15: Rail Assembly

Parts Needed:

3 - 64” Rail

3*- 34” Rail

3*- Rail Coupler

3 - Round End Caps

3 - Square End Caps

18 - M5 X 16mm Socket Head Screw

36*- M5 X 10mm Socket Head Screw

* Queen, ONLY

• Next, insert a M5 X 16mm socket

head screw through the hole and

into the square nut of the end cap.

• Follow the above instructions to

put the rest of the square end caps

on the 64” Rails.

• If you are setting up your frame

in crib you will put a round end

cap on the other end in the same

manner as above.

• First you will install one square end cap on the end of each 64” Rail.

Ratchet Wheel

64” Rail

34” Rail

Queen Size Rail

M5 X 10mm Socket

Head Screw

• Place a ratchet wheel on

each of the square plastic

end caps. Place two of

the ratchet wheels on the

rails so the teeth arc in a

clockwise direction and the

third rail so the teeth on the

ratchet wheel arc counter-

clockwise.

Step 16: Rails to Frame Assembly

Parts Needed: 3- Ratchet Wheels

6 - M4 X 30mm Screw

6 - End Cap Shoulders

• If you are setting your frame up in the queen size, you will need to add a coupler to the end that does not have

the square end cap on the 64” Rail.

• First, insert one end of the coupler into the end of the rail. Insert a M5 X 10mm socket head screw through each

hole of the rail and into the threaded hole of the coupler. Tighten this screw all the way.

• Repeat this step for the other end of the coupler, connecting it to the 34” rail.

• Note the direction in which the teeth arc on the ratchet wheel in the picture on the following page. The teeth

arc clockwise on the upper two rails and counter-clockwise on the lower rail.

**To make it easier to put your rails in you could loosen both knobs on your Left and Right Rail Mount Ends.

This will allow you to move your Rail Moutn Ends away from your frame slightly, making it easier to insert

your rails on your frame.

Page is loading ...

Grace Company Little Gracie II Operating instructions

Brand: Grace Company

Model: Little Gracie II

Type: Operating instructions

This manual is also suitable for

The Little Gracie II

Download PDF

report

Grace Company Little Gracie II Operating instructions

This manual is also suitable for

Grace Company Little Gracie II Operating instructions

Related papers

Other documents