Haworth 7029-9907c Operating instructions

Brand
Haworth
Model
7029-9907c
Type
Operating instructions
15
43
2
3.150
.75
Tools Required
Part No: Rev:
Page:
E.C.O. No: 1 OF 7 7029-9907
CUSTOMER SERVICE PHONE: 1-800-426-8562
C351-076
Digital Lock
Installation Instructions
A
G
H
J
K
B
C
Knob
Cam Stop
Lock Housing
Foam Tape
Mounting Nut
Mounting Washer
Battery Holder
5/64” Drill Bit 1.5mm
Allen
Battery Holder
Screw
D1
F
Spacer
E
Spindle
D2
Spacer
L
Mounting
Hardware
.39
1.00
3.86
1.00”
Mounting Template
Gereral Dimensions
Parts
.75
A
D1
C
C
L
D2
D3
D1
A
F
Part No: Rev:
Page:
E.C.O. No: 2 OF 7 7029-9907
CUSTOMER SERVICE PHONE: 1-800-426-8562
C351-076
INSTALLATION
1Remove lock core (AG)
with round key (CK) 2
3 4 5 6
AG
CK-1,2 OR 3
7
8a 8b
1
1
2
2
2
3.150
.75
1.00”
Mounting Template
15/64"
Drill
NOTE: Allow double stick tape to cure for 72 hours.
NOTE: Tape (F) NOT used with spacer (D2).
NOTE: The spacer (D2) is used only when trim ring (D3)
is either not removable or by customer preference.
E
E
E
E1 E1
A
OR
K
Part No: Rev:
Page:
E.C.O. No: 3 OF 7 7029-9907
CUSTOMER SERVICE PHONE: 1-800-426-8562
C351-076
OPTIONAL: ROTATIONAL STOP
BATTERY INSTALLATION
9
12
3 4
10
11a 11b
2
FASTEN KNOB
1
1
1
2
2
CC
J
J1
J1
J1
C
C
B
A
J1
NOTE: If necessary program lock
to rotate knob (see page 4).
NOTE: If necessary use factory
programed Supervisor code (1-2-3) to
unlock unit after battery installation.
4545
OR
45
OR
90° Rotation 180° Rotation
NOTE: Make sure unit (C)
is locked before installing
knob (A).
PROGRAMING LOCK (STATION MODE)
OVERIDE MASTER CODE (STATION MODE)
1
2
Part No: Rev:
Page:
E.C.O. No: 4 OF 7 7029-9907
CUSTOMER SERVICE PHONE: 1-800-426-8562
C351-076
1
1
2
2
3 4 5 6
A1
(2+4)=6
NOTE: The numbers 6,7,8, and 9 can be entered by pressing two
keys simultaneously in order to produce a sum.
NOTE: If the code was programmed using 2+4 as the 6 digit, the 2+4
must be used when accessing the lock, because other combinations
that equal six such as 1+5 are distinguished from 2+4.
1. PRESS
2. PRESS 4. PRESS
5. PRESS
3. PRESS
Press Program button (A1) 5x
Enter Factory Master Code (C1)
1-3-5-2-4-3
C1
NOTE:
A) If the code is entered correctly the
Green and Red LED will stay lit.
B) If the code is enter incorrectly, the Red
LED’s will ash 3 times.
3
1 2 3 4 5 6
Re-Enter Factory Master Code (C1)
1-3-5-2-4-3
C1
NOTE:
A) The Green, Red and Yellow LED’s
will stay lit.
4Enter New 6 digit Master Code (C1)
1-2-4-2-5-7
C1
NOTE:
A) The Green, Red and Yellow LED’s
will turn o briey then back on.
NOTE: Green LED will
light up and stay on.
Red
Error
LED Keypad
Green
Proceed
LED
Yellow
Low battery
LED
Program button
(Push thin front
edge inward)
Location to
point the
key-fob
Knob
in locked
position
Battery
holder
with cover
Knob
in unlocked
position
1 2 3 5 4 6
5Re-Enter New 6 digit Master Code (C1)
1-2-4-2-5-7
C1
NOTE:
A) If correctly done the Green, Red
and Yellow LED’s will ash 6x. 1 2 3 5 4 6
PROGRAMING LOCK (STATION MODE)
PROGRAM A SUPERVISOR CODE (STATION MODE)
1
2
Part No: Rev:
Page:
E.C.O. No: 5 OF 7 7029-9907
CUSTOMER SERVICE PHONE: 1-800-426-8562
C351-076
1 2 3 4 5 6
A1
Red
Error
LED Keypad
Green
Proceed
LED
Yellow
Low battery
LED
Program button
(Push thin front
edge inward)
Location to
point the
key-fob
Knob
in locked
position
Battery
holder
with cover
(2+4)=6
NOTE: The numbers 6,7,8, and 9 can be entered by pressing two
keys simultaneously in order to produce a sum.
NOTE: If the code was programmed using 2+4 as the 6 digit, the 2+4
must be used when accessing the lock, because other combinations
that equal six such as 1+5 are distinguished from 2+4.
PRESS
Press Program button (A1)
4
A1
PRESS
Press Program button (A1)
Enter Master Code (C1)
1-3-5-2-4-3
5313
C1
X
3
3 2 1 4
Enter Supervisor Code (X) (3-6 digits)
PROGRAM A USER CODE (STATION MODE)
1
A1
PRESS
PRESS
Press Program button (A1) two times
4
A1
PRESS
Press Program button (A1)
31531
Z
3
2 1 5 4 3
Enter User Code (Z) (3-6 digits)
NOTE: Supervisor Code (X) is
an example.
5313
X
2
3 2 1 4
Enter Supervisor Code (X)
NOTE: User Code (X) is an
example.
NOTE: If Master Code (C1) has
been overwritten refer to the
New Master code.
NOTE:
A) By not entering a Code within 6 seconds, will cause
the red light to ash 2 or 3 times and exit programming.
B) If you enter the Master Code incorrectly the red light
will ash 3 times and exit programming.
C) If you enter the Master code correctly, the red light
will light up for 6 seconds.
NOTE: You must enter
the user code (X) within
the 6 second window
after the master code is
entered.
NOTE: You must enter
the user code (Z) within
the 6 second window
after the master code is
entered.
NOTE:
A) By not entering a Code within 6 seconds, will cause
the red light to ash 3 times and exit programming.
B) If you enter the Supervisor Code incorrectly the red
light will ash 3 times and exit programming.
C) If you enter the Supervisor code correctly, the red
light will light up for 6 seconds.
NOTE:
A) A successful code storing
is indicated by 6 green light
ashes.
NOTE:
A) A successful code storing
is indicated by 6 green light
ashes.
LOCKER MODE - OPERATION
1Turn knob to unlocked position
UNLOCK USING MASTER CODE (LOCKER MODE)
1
A1
PRESS
Press Program button (A1)
5313
X
3 2 1 4
NOTE:
A) If the code is incorrect the red LED will blink 3 times. If
an incorrect code is entered 5 consecutive times, the lock
will not accept new codes for approximately 2 minutes
and will blink the red error light 3 times if codes are
attempted to be entered during the 2 minute period.
B) If the code is correct the lock will unlock and the
one-time User code will be erased.
5313
X
2
3 2 1 4
Enter 4 digit User Code (X)
NOTE: User Code (X) is an
example.
1
Knob
in unlocked
position
5
Knob
in unlocked
position
3Turn knob to lock poistion
4Enter code and turn knob to open
1
Knob
in locked
position
NOTE:
A) The green LED will light up.
B) If the lock is currently locked with a
one-time User code, the red light will
blink every 3 seconds.
NOTE:
A) If you turn the knob to the locked position
without entering a code or after 6 seconds,
the red LED will blink 3 times and not lock.
B) The green LED will blink twice after the
lock is locked.
Part No: Rev:
Page:
E.C.O. No: 6 OF 7 7029-9907
CUSTOMER SERVICE PHONE: 1-800-426-8562
C351-076
5
Knob
in unlocked
position
2
1 2 3 4 5 6
Enter Master Code (C1)
1-3-5-2-4-3
C1
NOTE: If Master Code (C1) has
been overwritten refer to the
New Master code.
NOTE:
A) If the Master code is entered correctly
the Green LED will light.
B) If the Master code is not entered within
10 seconds, the red LED will blink 3 times.
C) If the Master code is entered incorrectly,
the red LED will blink 3 times.
NOTE:
A) If the knob is left in the unlocked position for more than 20 seconds,
the one-time User code will be erased (if currently programmed in).
B) If the knob is returned to the locked position in less than 20 seconds,
the unit will re-lock and the one-time User code will be maintained.
4Enter code and turn knob to open
OVERIDE MASTER CODE (LOCKER MODE)
1Turn knob to unlocked position
2
A1
PRESS
Press Program button (A1)
1
Knob
in unlocked
position
Part No: Rev:
Page:
E.C.O. No: 7 OF 7 7029-9907
CUSTOMER SERVICE PHONE: 1-800-426-8562
C351-076
3
1 2 3 4 5 6
Enter Master Code (C1)
1-3-5-2-4-3
C1
4Enter the new 6-digit Master Code
NOTE:
A) If the code is entered correctly the
Green LED will light up for 6 seconds.
B) If the code is entered incorrectly, the
red LED will blink 3 times and exit
programming.
C) If the code is not entered within 6
seconds, the red LED will blink 3 times
and exit programming.
NOTE:
A) If the code is valid the Green LED will
blink 7 times. The factory code is erased.
B) If the code is invalid (not 6 digits) the
red LED will blink 3 times and exit
programming.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Haworth 7029-9907c Operating instructions

Brand
Haworth
Model
7029-9907c
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents