Ruckus Wireless SCG-200 Getting Started Manual

Ruckus Wireless

™

SmartCell Gateway

™

200

Getting Started Guide for SmartZone 3.4

Part Number 800-71126-001 Rev A

Published July 2016

www.ruckuswireless.com

SmartCell Gateway 200 Getting Started Guide for SmartZone 3.4, 800-71126-001 Rev A 2

Copyright Notice and Proprietary Information

No part of this documentation may be used, reproduced, transmitted, or translated, in any form or by any means,

electronic, mechanical, manual, optical, or otherwise, without prior written permission of Ruckus Wireless, Inc.

(“Ruckus”), or as expressly provided by under license from Ruckus.

Destination Control Statement

Technical data contained in this publication may be subject to the export control laws of the United States of America.

Disclosure to nationals of other countries contrary to United States law is prohibited. It is the reader’s responsibility to

determine the applicable regulations and to comply with them.

Disclaimer

THIS DOCUMENTATION AND ALL INFORMATION CONTAINED HEREIN (“MATERIAL”) IS PROVIDED FOR GENERAL

INFORMATION PURPOSES ONLY. RUCKUS AND ITS LICENSORS MAKE NO WARRANTY OF ANY KIND, EXPRESS

OR IMPLIED, WITH REGARD TO THE MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES

OF MERCHANTABILITY, NON-INFRINGEMENT AND FITNESS FOR A PARTICULAR PURPOSE, OR THAT THE

MATERIAL IS ERROR-FREE, ACCURATE OR RELIABLE. RUCKUS RESERVES THE RIGHT TO MAKE CHANGES OR

UPDATES TO THE MATERIAL AT ANY TIME.

Limitation of Liability

IN NO EVENT SHALL RUCKUS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUEN-

TIAL DAMAGES, OR DAMAGES FOR LOSS OF PROFITS, REVENUE, DATA OR USE, INCURRED BY YOU OR ANY

THIRD PARTY, WHETHER IN AN ACTION IN CONTRACT OR TORT, ARISING FROM YOUR ACCESS TO, OR USE

OF, THE MATERIAL.

Trademarks

Ruckus Wireless, Ruckus, Bark Logo, BeamFlex, ChannelFly, Ruckus Pervasive Performance, SmartCell, ZoneFlex,

Dynamic PSK, FlexMaster, MediaFlex, MetroFlex, Simply Better Wireless, SmartCast, SmartMesh, SmartSec, Speed-

Flex, ZoneDirector, ZoneSwitch, and ZonePlanner are trademarks of Ruckus Wireless, Inc. in the United States and

other countries. All other product or company names may be trademarks of their respective owners.

SmartCell Gateway 200 Getting Started Guide for SmartZone 3.4, 800-71126-001 Rev A 3

Contents

About This Guide

Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Documentation Feedback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1 Preparing to Set Up the SmartCell Gateway 200

Unpacking the SCG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Verifying the Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Rack Mount Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Prepare the Required Hardware and Tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Get to Know the Physical Features of the SCG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2 Mounting and Powering the SCG

Mounting the SCG onto a Server Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

What You Will Need . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Step 1: Unpack the Rack Mount Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Step 2: Separate the Slide Rails into the Inner and Outer Parts . . . . . . . . . . . . . . . . . . . . 23

Step 3: Install the Outer Rail Slides to the Rack Posts. . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Step 4: Fasten the Shoulder Screws to the Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Step 5: Install the Inner Rails on the Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Step 6: Fasten the Inner Rails to the Server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Step 7: Attach the Mounting Ears to the Rail Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . 27

Step 8: Slide the Rail Assembly into the Outer Rails and Secure to the Rack . . . . . . . . . 27

Powering On the SCG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Using AC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Using DC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

3 Preparing the Interface Settings and Administrative Computer

Preparing the SCG Interface Settings to Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

IPv6 Address Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Preparing the Administrative Computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

SmartCell Gateway 200 Getting Started Guide for SmartZone 3.4, 800-71126-001 Rev A 4

4 Running the Setup Wizard and Logging On to the Web Interface

Overview of the SCG Setup Wizard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Step 1: Start the Setup Wizard and Set the Language . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Step 2: Configure the Management IP Address Settings. . . . . . . . . . . . . . . . . . . . . . . . . 41

Important Notes About Selecting the System Default Gateway . . . . . . . . . . . . . . . . . . 47

Step 3: Configure the DataPlane IP Address Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Step 4: Configure the Cluster Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

If This Controller Is Forming a New Cluster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

If This Controller Is Joining an Existing Cluster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Step 5: Verify the Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Connecting Data Blades to the Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Supported SFP+ Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Logging On to the Web Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

5 Configuring the SCG for the First Time

Creating an AP Zone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Configuring AAA Servers and Hotspot Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Adding an AAA Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Creating a Hotspot (WISPr) Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Creating a Registration Rule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Configuring the Rule Priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Defining the WLAN Settings of an AP Zone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

General Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

WLAN Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Authentication Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Encryption Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Authentication & Accounting Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

RADIUS Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Advanced Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Verifying That Wireless Clients Can Associate with a Managed AP . . . . . . . . . . . . . . . . . 83

What to Do Next . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

6 Ensuring That APs Can Discover the Controller on the Network

Is LWAPP2SCG Enabled on the Controller? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Obtaining the LWAPP2SCG Application. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Enabling LWAPP2SCG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Method 1: Perform Auto Discovery of the Controller Using the SmartLicense Server. . . . 87

Method 2: Perform Auto Discovery on Same Subnet, then Transfer the AP to Intended

SmartCell Gateway 200 Getting Started Guide for SmartZone 3.4, 800-71126-001 Rev A 5

Subnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Method 3: Register the Controller with the DNS Server . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Method 4: Configure DHCP Option 43 on the DHCP Server . . . . . . . . . . . . . . . . . . . . . . 91

Method 5: Manually Configure the Controller Address on the AP’s Web Interface . . . . . . 94

What to Do Next . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Index

SmartCell Gateway 200 Getting Started Guide for SmartZone 3.4, 800-71126-001 Rev A 6

About This Guide

This SmartCell Gateway™ 200 Getting Started Guide provides information on how

to set up the SmartCell Gateway 200 (SCG-200 or “the controller”) appliance on

the network. Topics covered in this guide include mounting, installation, and basic

configuration.

This guide is intended for use by those responsible for installing and setting up

network equipment. Consequently, it assumes a basic working knowledge of local

area networking, wireless networking, and wireless devices.

NOTE: If release notes are shipped with your product and the information there

differs from the information in this guide, follow the instructions in the release notes.

Most user guides and release notes are available in Adobe Acrobat Reader Portable

Document Format (PDF) or HTML on the Ruckus Wireless Support website at

https://support.ruckuswireless.com/documents.

About This Guide

Document Conventions

SmartCell Gateway 200 Getting Started Guide for SmartZone 3.4, 800-71126-001 Rev A 7

Document Conventions

Tab l e 1 and Table 2 list the text and notice conventions that are used throughout

this guide.

Related Documentation

In addition to this Getting Started Guide, each SmartCell Gateway 200 documen-

tation set includes the following:

• Administrator Guide: Provides detailed information on how to configure the SCG.

The Administrator Guide is available for download on the Ruckus Wireless

Support website at http://support.ruckuswireless.com.

• Online Help: Provides instructions for performing tasks using the SCG web

interface. The online help is accessible from the web interface and is searchable.

• Release Notes: Provide information about the current software release, including

new features, enhancements, and known issues.

Table 1. Text conventions

Convention Description Example

monospace

Represents information as it

appears on screen

[Device name]>

monospace bold

Represents information that

you enter

[Device name]> set

ipaddr 10.0.0.12

default font bold

Keyboard keys, software

buttons, and field names

On the Start menu, click All

Programs

.

italics Screen or page names Click

Advanced Settings. The

Advanced Settings page

appears.

Table 2. Notice conventions

Notice Type Description

NOTE

Information that describes important features or instructions

CAUTION!

Information that alerts you to potential loss of data or potential

damage to an application, system, or device

WARNING!

Information that alerts you to potential personal injury

About This Guide

Documentation Feedback

SmartCell Gateway 200 Getting Started Guide for SmartZone 3.4, 800-71126-001 Rev A 8

NOTE: For a complete list of documents that accompany this release, refer to the

Release Notes.

Documentation Feedback

Ruckus Wireless is interested in improving its documentation and welcomes your

comments and suggestions. You can email your comments to Ruckus Wireless at:

[email protected]

When contacting us, please include the following information:

• Document title

• Document part number (on the cover page)

• Page number (if appropriate)

For example:

• SmartCell Gateway 200 Getting Started Guide for SmartZone 3.4

• Part number: 800-71126-001

• Page 88

SmartCell Gateway 200 Getting Started Guide for SmartZone 3.4, 800-71126-001 Rev A 9

1

Preparing to Set Up the SmartCell

Gateway 200

In this chapter:

• Unpacking the SCG

• Verifying the Package Contents

• Before You Begin

Preparing to Set Up the SmartCell Gateway 200

Unpacking the SCG

SmartCell Gateway 200 Getting Started Guide for SmartZone 3.4, 800-71126-001 Rev A 10

Unpacking the SCG

WARNING! The SCG appliance is heavy (40 lbs/18.14kg). Two people should work

together to unpack the SCG. Ruckus Wireless strongly recommends against one

person attempting to perform this task alone.

Follow these steps to unpack the SCG appliance.

1 Open the SCG package, and then carefully remove the contents.

2 Return all packing materials into the shipping box, and then put the box away

in a dry location.

3 Verify that all of the items listed in Verifying the Package Contents (below) are

included in the package. Check each item for damage. If any item is damaged

or missing, notify your authorized Ruckus Wireless sales representative

immediately.

Verifying the Package Contents

A complete SCG package contains all of the items listed below:

• One SCG appliance with two AC/DC power supply units

• One console cable (use only this cable to connect the front or rear serial port via

a laptop/notebook)

• One rack mount kit (see Rack Mount Kit Contents below)

• Service Level Agreement / Limited Warranty Statement sheet

• Regulatory Statement sheet

•This Getting Started Guide

NOTE: The AC power cable (part number 902-0174-XX00, where XX is the two-

character country code) is not supplied with the SCG appliance and may be ordered

separately.

Preparing to Set Up the SmartCell Gateway 200

Verifying the Package Contents

SmartCell Gateway 200 Getting Started Guide for SmartZone 3.4, 800-71126-001 Rev A 11

Rack Mount Kit Contents

The rack mount kit contains the following items:

• Outer rail slide assembly (see A in Figure 1)

• Inner rail slide assembly (see B in Figure 1)

• Plastic bag #1, which contains the following items:

• Four hex head shoulder screws

• Two #10-32 x 3/8” screws

• Two rack mounting ears

• Plastic bag #2, which contains the following items:

• Outer slide rail screws, 8 #8-32 x 1/2 (see D in Figure 1)

• Inner slide rail screws, 8 #6-32 x 1/4 (see D in Figure 1)

• Rack screws, 2 #8-32 x 3/4 (see D in Figure 1)

•The SmartCell Gateway 200 Rack Mount Installation Guide

NOTE: This rack mount kit includes two sets of 8-32 x 1/2” screws. One set of

eight has a larger screw head size than the second set of eight. Use the set of 8-

32 x 1/2” screws that best fits the rack in which you are installing the rail kit.

Preparing to Set Up the SmartCell Gateway 200

Verifying the Package Contents

SmartCell Gateway 200 Getting Started Guide for SmartZone 3.4, 800-71126-001 Rev A 12

Figure 1. Rail assemblies and rail screws

Preparing to Set Up the SmartCell Gateway 200

Before You Begin

SmartCell Gateway 200 Getting Started Guide for SmartZone 3.4, 800-71126-001 Rev A 13

Before You Begin

Before installing and setting up the SCG, Ruckus Wireless recommends that you

first complete the following pre-installation tasks.

Prepare the Required Hardware and Tools

You must supply the following tools and equipment:

• A switch or router with 10GbE interfaces (for connecting the SCG to the

backbone network)

NOTE: A fast ethernet or gigabit switch/router is required to upload management,

cluster, and configurations. A 10GBE switch/router is only required if the customer

is going to use tunnels.

• A Phillips #1 screwdriver

• A flat head screwdriver

• An administrative computer (desktop or laptop) running Windows 8/7/Vista/XP

or Mac OS X, containing a minimum RAM of 13G, with a web browser installed

(Google Chrome recommended). Supported web browsers include:

• Google Chrome 15 (and later)

• Safari 5.1.1 (and later)

• Mozilla Firefox 8 (and later)

• Microsoft Internet Explorer 9.0

• A grounded electrical power strip or surge suppressor to protect from circuit

overload

• A standard EIA 19-inch wide rack with an available 2RU space

• Two SFP+ modules (see Supported SFP+ Modules). For a redundant setup, you

will need four SFP+ modules.

NOTE: At the beginning of each procedure, this guide lists the specific tools,

accessories, or equipment that you will need to complete that procedure.

Preparing to Set Up the SmartCell Gateway 200

Before You Begin

SmartCell Gateway 200 Getting Started Guide for SmartZone 3.4, 800-71126-001 Rev A 14

Get to Know the Physical Features of the SCG

The following sections identify the physical features of the SCG that are relevant to

the installation and mounting instructions that this guide provides. Before you begin

the installation process, Ruckus Wireless strongly recommends that you become

familiar with these physical features.

Front Panel

Figure 2 shows the SCG front panel with the bezel installed. For descriptions of the

numbered parts, refer to Tab l e 1 .

Figure 2. SCG front panel with the bezel

Table 1. SCG front panel parts

Number Description

1 Control panel (see Control Panel on the Front Panel)

2 RJ45 serial port (COM2/serial B). Use only the console cable provided to

connect this port via a laptop/notebook.

CAUTION! The SCG has two RJ45 serial ports – one on the front panel

and one on the rear panel. You can only use one of these two ports at any

given time. Using them simultaneously may cause both serial ports to

become unresponsive.

3 Use the USB port to connect a keyboard and mouse. Use a USB stick

(for a fresh installation).

4 Front bezel lock

1

2

3 4

Preparing to Set Up the SmartCell Gateway 200

Before You Begin

SmartCell Gateway 200 Getting Started Guide for SmartZone 3.4, 800-71126-001 Rev A 15

Front Panel Without the Bezel

Figure 3 shows the front panel of the SCG without the bezel. For descriptions of the

numbered parts, refer to Tab l e 2 .

Figure 3. SCG front panel without the bezel

Table 2. SCG front panel parts (without the bezel)

Number Description

1 ESD ground strap attachment

2 Hard drive bays (the SCG has two 600GB hard drives)

3 Control panel (buttons and status indicators, see Control Panel on the

Front Panel)

4 RJ45 serial port (COM2 / serial B). Use only the console cable provided to

connect this port to another device.

CAUTION! The SCG has two RJ45 serial ports – one on the front panel

and one on the rear panel. You can only use one of these two ports at any

given time. Using them simultaneously may cause both serial ports to

become unresponsive.

5 USB port (not used)

1

2 3

4

5

Preparing to Set Up the SmartCell Gateway 200

Before You Begin

SmartCell Gateway 200 Getting Started Guide for SmartZone 3.4, 800-71126-001 Rev A 16

RJ45 Serial Port Pinouts

The following table shows the pinouts for the RJ45 serial ports on the front and rear

panels.

Control Panel on the Front Panel

Figure 4 shows the control panel on the front panel of the SCG. For descriptions of

the numbered parts, refer to Tab l e 4 .

Figure 4. Control panel on the SCG front panel

Table 3. RJ45 serial port pinouts

Pin Signal Name Description

1 SPB_RTS RTS (request to send)

2 SPB_DTR DTR (data terminal ready)

3 SPB_OUT_N TXD (transmit data)

4 GND Ground

5 SPB_RI RI (ring indicate)

6 SPB_SIN_N RXD (receive data)

7 SPB_DCR_DCD Data Set Ready/Data Carrier Detect

8 SPB_CTS CTS (clear to send)

Table 4. Control panel parts

Number Description

1 Power button

2 System reset button

3 System status LED

12

11

10

9

8

7

1

2 3 4

5 6

Preparing to Set Up the SmartCell Gateway 200

Before You Begin

SmartCell Gateway 200 Getting Started Guide for SmartZone 3.4, 800-71126-001 Rev A 17

Rear Panel

Figure 5 shows the rear panel of the SCG. For descriptions of the numbered parts,

refer to Ta b l e 5 .

Figure 5. SCG rear panel

4 Fan status LED

5 Critical alarm (not implemented in this release)

6 MJR alarm LED (not implemented in this release)

7 NMI pin hole button (factory reset button)

8 Chassis ID button

9 NIC1/NIC2 activity LED

10 HDD activity LED (flashing green: HDD activity; amber: HDD fault; off: no

access or no HDD fault)

11 PWR alarm LED (not implemented in this release)

12 Minor alarm (amber: system unavailable; off: system available)

Table 4. Control panel parts (Continued)

Number Description

1

2

3

4

5

6

7

8 9 10 11

12

Preparing to Set Up the SmartCell Gateway 200

Before You Begin

SmartCell Gateway 200 Getting Started Guide for SmartZone 3.4, 800-71126-001 Rev A 18

NOTE: The power supply locations (numbers 5 and 6) are for AC or DC power. AC

power supply is pictured.

Table 5. SCG rear panel parts

Number Description

1 Cable connector

2 Two low-profile PCIe interface cards that include four ports – one for

management traffic and three for redundancy. See Redundant Interfaces

on the SCG.

3 PCIe add-in card slot for DataPlane1

4 PCIe add-in card slot for DataPlane0

5 Power supply 2

6 Power supply 1

7 RJ45 serial port (COM2/serial B). Use only the console cable provided to

connect this port to another device.

CAUTION! The SCG has two RJ45 serial ports – one on the front panel

and one on the rear panel. You can only use one of these two ports at any

given time. Using them simultaneously may cause both serial ports to

become unresponsive.

NOTE: For information on how to access and use the SCG command line

interface, refer to the SmartCell Gateway 200 Virtual SmartZone High-

Scale Command Line interface Reference Guide.

8 Video connector

9 USB 0 and 1 (#1 on top)

10 USB 2 and 3 (#3 on top)

11 ETH1 GbE NIC for cluster traffic

12 ETH2 GbE NIC for control (between access points and the SCG controller)

traffic

Preparing to Set Up the SmartCell Gateway 200

Before You Begin

SmartCell Gateway 200 Getting Started Guide for SmartZone 3.4, 800-71126-001 Rev A 19

NIC LEDs on the Rear Panel

Tab l e 6 describes the behavior of the NIC LEDs on the rear panel of the SCG.

Table 6. LEDs on the SCG rear panel

LED Color LED State NIC State

Green/amber (left) Off 10Mbps

Green 100Mbps

Amber 1000Mbps

Green (right) On Active connection

Blinking Transmitting or receiving data

Preparing to Set Up the SmartCell Gateway 200

Before You Begin

SmartCell Gateway 200 Getting Started Guide for SmartZone 3.4, 800-71126-001 Rev A 20

Redundant Interfaces on the SCG

The SCG offers network redundancy options by providing redundant interfaces for

the three traffic types that it handles – control traffic, cluster traffic, and management

traffic. A redundant interface pairs an active interface and a standby interface. When

the active interface fails, the standby interface becomes active automatically and

takes over the job of passing traffic.

To enable a redundant interfaces pair, you need to connect the member ports

(see Ta b l e 7) to the same router or switch or to two different routers or switches,

depending on the network environment of your organization.

Figure 6 identifies the redundant interface pairs on the rear panel of the SCG and

Tab l e 7 lists the member ports of each redundant interface pair.

Figure 6. Redundant interfaces on the SCG

Table 7. Bridge groups, member interfaces, and traffic types

Member Ports Bridge Traffic Type

ETH1 and ETH3 Bridge 0 Control (SSH tunnels between APs and SCG)

traffic

ETH2 and ETH4 Bridge 1 Cluster traffic

ETH2 and ETH5 Bridge 2 Management (web interface) traffic

ETH2

ETH3

ETH4

ETH5

ETH1

ETH0

Page is loading ...

Ruckus Wireless SCG-200 Getting Started Manual

This manual is also suitable for

Ruckus Wireless SCG-200 Getting Started Manual

Related papers

Other documents