2/95
PALISADE™ 31”
LARGE SINGLE BOWL SINK
AMERICAST®
PALISADE 31” LARGE SINGLE BOWL KITCHEN
SINK
• Americast
®
brand engineered material
• Single bowl design
• Self-rimming or undercounter installation
• Color matched adhesive caulk supplied
Self-Rimming:
❏ 7103.000
Undercounter Installation:
❏ 791123-100 Mounting Kit (consists of
cut-out templates and mounting clips
Nominal Dimensions: 787 x 495 x 241mm
(31" x 19-1/2" x 9-1/2")
Bowl sizes:
679mm (26-3/4") wide, 413mm (16-1/4") front to
back 229mm (9") deep
Fixture Dimensions conform to ANSI Standard
A112.19.4
© 1995 American Standard Inc.
KSS-009
SPS 7103
* See faucet section for additional models available
To Be Specified
❏ Color:
❏ Faucet*:
❏ Faucet Finish:
❏ Basket Strainer: 4331.013
❏ Soap Dispenser: 4503.115, Color:
❏ Trap:
See reverse side for roughing-in dimensions
PALISADE™ 31”
LARGE SINGLE BOWL SINK
AMERICAST®
© 1998 American Standard Inc.
SPS 7103
7103.000 Self-Rimming
Undercounter Mount
FINISHED WALL OR SPLASHBACK
FINISHED FLOOR
914mm
(36)
TO FINISHED
FLOOR (OPTIONAL)
●
*3/8 O.D. BENDABLE TUBING
COUNTERTOP
BY OTHERS
SEALING
COMPOUND
FAUCET
RELIANT 4205.241
6270.142
TOP MOUNT
E
*
41mm(1-5/8)
495mm
(19-1/2)
787mm
(31)
394mm
(15-1/2)
213mm
(8-3/8)
203mm
(8)
229mm
(9)
146mm
(5-3/4)
(3) 38mm
(1-1/2) DIA.
HOLES IN
COUNTERTOP
38mm
(1-1/2)
RAD TYP.
89mm
(3-1/2)
DIA.
143mm
(5-5/8)
102mm
(4)
102mm
(4)
76mm
(3)
MIN.
38mm (1-1/2) MIN.
1-1/2 O.D.
TAILPIECE
CUTOUT NOTE
254mm*
(10)
E
COUPLING NUTS
ON FITTING
13mm
(1/2)
NOTES:
TEMPLATE PROVIDED WITH MOUNTING KIT 791123-100 FOR UNDER-
COUNTER, INSTALLATION AND COUNTERTOP CUTOUT.
FITTINGS AND UNDERCOUNTER MOUNTING KIT NOT INCLUDED AND
MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR WALL & COUNTERTOP SUP-
PORTS.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range
of tolerances established by ANSI Standard A112.19.4
These measurements are subject to change or cancellation. No responsibility is
assumed for use of superseded or voided leaflet.
●
●
NOTES:
COUNTERTOP CUTOUT 756mm X 464mm WITH 25mm RADIUS (29-3/4
X 18-1/4 WITH 1” RADIUS)
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR WALL & COUNTERTOP
SUPPORTS.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the
range of tolerances established by ANSI Standard A112.19.4
These measurements are subject to change or cancellation. No responsi-
bility is assumed for use of superseded or voided leaflet.
FINISHED WALL OR SPLASHBACK
FINISHED FLOOR
914mm
(36)
TO FINISHED
FLOOR (OPTIONAL)
●
*3/8 O.D. BENDABLE TUBING
COUNTERTOP
BY OTHERS
SEALING
COMPOUND
FAUCET
RELIANT 4205.241
6270.142
TOP MOUNT
E
*
41mm(1-5/8)
495mm
(19-1/2)
787mm
(31)
394mm
(15-1/2)
213mm
(8-3/8)
203mm
(8)
241mm
(9-1/2)
146mm
(5-3/4)
(3) 38mm
(1-1/2) DIA.
HOLES IN
COUNTERTOP
38mm
(1-1/2)
RAD TYP.
89mm
(3-1/2)
DIA.
143mm
(5-5/8)
102mm
(4)
102mm
(4)
76mm
(3)
MIN.
38mm (1-1/2) MIN.
1-1/2 O.D. TAILPIECE
CUTOUT NOTE
254mm*
(10)
E
COUPLING NUTS
ON FITTING
13mm
(1/2)
DETAIL OF MOUNTING CLIP
(KIT No.791123-100)
BRASS
INSERT
13mm
(1/2)
MIN.
REFER TO INSTRUCTIONS
PROVIDED WITH KIT FOR
ADDITIONAL INFORMATION
CLIP
MACH.
SCREW
SINK
MOUNTING CLIP
(SEE DETAIL)
/
