Road Armor Stealth Mid Width Front Winch Bumper Installation guide

Brand
Road Armor
Model
Stealth Mid Width Front Winch Bumper
Type
Installation guide

This manual is also suitable for

Road Armor Stealth Mid Width Front Winch Bumper

The Road Armor Stealth Mid Width Front Winch Bumper is designed to provide superior protection and functionality for your 2007-2018 Jeep Wrangler JK. Constructed from high-strength steel, this bumper is built to withstand the toughest off-road conditions. It features a winch plate that allows you to mount a winch for added recovery capabilities. The bumper also includes integrated fog light mounts and is compatible with factory fog lights.

In addition to its protective and functional features, the Road Armor Stealth Mid Width Front Winch Bumper also enhances the aesthetics of your Jeep. Its sleek and aggressive design complements the rugged look of the Wrangler JK. The bumper is available in a variety of finishes, including black powder coat, brushed aluminum, and polished stainless steel, so you can choose the option that best suits your style.

Road Armor Stealth Mid Width Front Winch Bumper

The Road Armor Stealth Mid Width Front Winch Bumper is designed to provide superior protection and functionality for your 2007-2018 Jeep Wrangler JK. Constructed from high-strength steel, this bumper is built to withstand the toughest off-road conditions. It features a winch plate that allows you to mount a winch for added recovery capabilities. The bumper also includes integrated fog light mounts and is compatible with factory fog lights.

In addition to its protective and functional features, the Road Armor Stealth Mid Width Front Winch Bumper also enhances the aesthetics of your Jeep. Its sleek and aggressive design complements the rugged look of the Wrangler JK. The bumper is available in a variety of finishes, including black powder coat, brushed aluminum, and polished stainless steel, so you can choose the option that best suits your style.

INSTALL INSTRUCTIONS
Jeep JK Front Mid-Width Bumper
Products: 5072F0B(BASE), 5072F3B(SM-PRERUNNER) &
5072F5B(STINGER)
Applicaon : 2007-2018 Jeep Wrangler JK
2007-20018 Jeep Wrangler JK Front Bumper Page ( 2 of 6)
www.ROADARMOR.com
INSTALL INSTRUCTIONS
SAFETY FIRST!
• FOLLOW ALL INSTRUCTIONS, YOUR SAFETY AND THE SAFETY OF OTHERS IS MOST IMPORTANT.
• WEAR APPROPRIATE EYE PROTECTION AND EXERCISE CAUTION WHEN DRILLING / CUTTING
REQUIRED TOOLS
INCLUDED HARDWARE & BRACKETS
I WARNING
Read the instrucons completely before beginning installaon. Before ghtening bolts,
drilling or cung where required, check to make sure there are no obstrucons such as
brake, fuel or electrical lines which may be damaged. Also keep in mind this is an aer-
market product and MAY require minor shimming and/or trimming, reaming, etc. for
proper t. Road Armor is not responsible for any damages to vehicle.
IMPORTANT NOTICE
• Be sure to inspect and test t your product to ensure proper tment before having it coated, painted, bed
lined, etc.
• Road Armor will not be responsible for the cost of coang your unit if any problems with t or nish are not
noted and addressed beforehand.
(2) 1/2-in x 1-in Hex Head Bolts (2) 1/2-in Nut Plate (Winch)
(4) 1/2-in x 1.5-in Hex Head Bolts (6) Wire
(14) 1/2-in Grade 8 Nuts (4) 20-Gauge Bu Connector
(14) 1/2-in Grade 8 Lock Washers (1) JK Pump Bracket
(18) 1/2-in Large Grade 8 Washers (1) JK Winch Plate
(8) 1/2-in x 1.5-in Hex Head Bolt Tabs
(8) 1/2-in Small Retainer Washers
(1) Stain Steel Road Armor Logo Leers
Metric and SAE Socket Sets and Wrenches Phillips Screwdriver & Cut-O Wheel
Needle Nose Pliers, Small Pry Bar or Large Flathead Screwdriver 9/16 Drill Bit or Step Bit
2007-20018 Jeep Wrangler JK Front Bumper Page ( 3 of 6)
www.ROADARMOR.com
INSTALL INSTRUCTIONS
1 Unscrew the four (4) plasc screws in the center of the retainer clips securing the factory air dam
to the boom of the bumper using a phillips screw driver.
TIP If the screws just spin use a athead screwdriver or small pry bar to pop them out.
2 There two (2) more of these plasc screw type retainers on the backside of the front cross member
which must be removed in the same fashion.
3 If your JK is equipped with factory fog lights unplug them.
4 Using a pair of needle nose pliers, pry o all the clips
holding the fog light harness loom to bumper.
1 2
4
3
5
5 Remove the nuts holding the factory bumper on, four (4) on each side using an 18mm socket and
socket wrench. Keep the backing plate for installing Road Armor Bumper.
2007-20018 Jeep Wrangler JK Front Bumper Page ( 4 of 6)
www.ROADARMOR.com
INSTALL INSTRUCTIONS
6 Pull o factory bumper and set aside. It is not heavy, about 25lbs.
7 Now remove the plasc top plate using a phillips screwdriver as in Steps 1 and 2. Again if the
screw simply spins, employ a athead screwdriver or small pry bar as shown.
8 Gather a drill, a
9/16-in drill bit
or a Step Bit for
the next Step.
**2012-2018 Jeep Wrangler JK— Relocate AIR PUMP**
9 Drill out the holes on the frame as circled below to 9/16-in.
10 Remove air pump and bracket from frame. Extend wires & relocate pump using provided bracket.
7
9
10
2007-20018 Jeep Wrangler JK Front Bumper Page ( 5 of 6)
www.ROADARMOR.com
INSTALL INSTRUCTIONS
11 2012-2018 JK: Cut and remove small secons of crash bar on both DVR & PSG side for bumper.
12 2007-2018 JK: Cut and remove small secons of frame horn on both DVR & PSG side for winch.
11 12
13 Install winch plate using 1/2” x 1” hardware & nut plates as shown below. (Install WINCH as well.)
13
14 Install Road Armor Logo using the Stainless #10 Buon Head Bolts and Keps Nuts.
15 Install both cube lights, fairlead and 2 - 1/2” bolt tabs on each outer slots of bumper using retainer
washers to hole install bumper using large washers on the outside
15
2007-20018 Jeep Wrangler JK Front Bumper Page ( 6 of 6)
www.ROADARMOR.com
INSTALL INSTRUCTIONS
16 Install bumper onto frame-horn lining up outside holes and each 1/2” bolt tabs through frame.
Then place the factory outer seners, which you were instructed to set aside in Step 5, followed
by a washer (Large), lock-washer and nut on the backside nger ght. Repeat for Dvr. side.
17 Install two (2) 1/2” bolt, washer (Small), lock-washer and nut through bumper, inside-frame-horn
and kit winch plate as shown above. Repeat for Dvr. Side (Use small washer for proper t)
18 Once all the bolts are installed and bumper is adjusted properly; ghten all bolts at this me.
19 Install 4 - 1/2” bolt, washer, lock-washer and nut through lower bumper and crash bar.
20 If you have a winch to install, do that at this me. (Be sure all wires are secured.) Finished!
16
17
18
17
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Road Armor Stealth Mid Width Front Winch Bumper Installation guide

Brand
Road Armor
Model
Stealth Mid Width Front Winch Bumper
Type
Installation guide
This manual is also suitable for

Road Armor Stealth Mid Width Front Winch Bumper

The Road Armor Stealth Mid Width Front Winch Bumper is designed to provide superior protection and functionality for your 2007-2018 Jeep Wrangler JK. Constructed from high-strength steel, this bumper is built to withstand the toughest off-road conditions. It features a winch plate that allows you to mount a winch for added recovery capabilities. The bumper also includes integrated fog light mounts and is compatible with factory fog lights.

In addition to its protective and functional features, the Road Armor Stealth Mid Width Front Winch Bumper also enhances the aesthetics of your Jeep. Its sleek and aggressive design complements the rugged look of the Wrangler JK. The bumper is available in a variety of finishes, including black powder coat, brushed aluminum, and polished stainless steel, so you can choose the option that best suits your style.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents