American Dynamics MegaPower 168 Installation and Service Manual

MegaPower 168

Matrix Switcher/Controller System

Installation & Service Manual

MegaPower 168

Matrix Switcher/Controller System

Installation & Service Manual

No part of this manual may be reproduced in any form

without written permission from Sensormatic

®

Electronics Corporation.

8000-0934-01, Revision C

06/02

WARNING

Do not install this product in hazardous areas where highly combustible or explosive

products are stored or used.

FCC COMPLIANCE

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against interference when the equipment is operated in a

commercial environment. The equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause interference to radio communications.

Operation of this equipment in a residential area may cause interference in which case the user will be required to correct the

interference at his own expense.

EQUIPMENT MODIFICATION CAUTION

Equipment changes or modifications not expressly approved by Sensormatic Electronics Corporation, the party responsible for FCC

compliance, could void the user's authority to operate the equipment, and could create a hazardous condition.

WARRANTY DISCLAIMER

Sensormatic Electronics Corporation makes no representation or warranty with respect to the contents hereof and specifically

disclaims any implied warranties of merchantability or fitness for any particular purpose. Further, Sensormatic Electronics

Corporation reserves the right to revise this publication and make changes from time to time in the content hereof without obligation

of Sensormatic Electronics Corporation to notify any person of such revision or changes.

American Dynamics, the AD logo, Sensormatic, the Sensormatic hand logo, and TouchTracker are all registered trademarks of

Sensormatic Electronics Corporation

Table of Contents

PREFACE .................................................................................................................... I

Who Should Use This Manual ............................................................................................................... i

How To Use This Manual ....................................................................................................................... i

Related Documents ................................................................................................................................ ii

Ordering Documents.............................................................................................................................. ii

Questions? .............................................................................................................................................. ii

CHAPTER 1 DESCRIPTION........................................................................................ 1-1

GENERAL DESCRIPTION ...................................................................................................................... 1-1

MP168 Bay Construction.................................................................................................................... 1-2

Bay Housing - Front ........................................................................................................................ 1-2

Front Panel....................................................................................................................................... 1-2

MP168 Bay Modules........................................................................................................................ 1-2

Circuit Cards .................................................................................................................................... 1-2

Bay Housing - Rear ......................................................................................................................... 1-3

Rear Panel Assembly...................................................................................................................... 1-3

POWER SUPPLY MODULE .................................................................................................................... 1-4

Power Supply Module Features......................................................................................................... 1-4

A. Printer Port ................................................................................................................................. 1-4

B. Data Line BNC Connectors....................................................................................................... 1-4

C. ARCNET Connector................................................................................................................... 1-5

D. Primary Power Connector ........................................................................................................ 1-5

E. Redundant Power Connector................................................................................................... 1-5

F. External Sync I/O Connectors .................................................................................................. 1-5

Color Code ....................................................................................................................................... 1-5

CENTRAL PROCESSING UNIT MODULE ............................................................................................. 1-6

Connections..................................................................................................................................... 1-7

Program Monitor.............................................................................................................................. 1-7

Color Code ....................................................................................................................................... 1-7

VIDEO INPUT MODULES........................................................................................................................ 1-8

Video Input Module 1 .......................................................................................................................... 1-9

Video Input Modules 2 and 3 ............................................................................................................. 1-10

Video Input Module 4 .......................................................................................................................... 1-11

VIDEO OUTPUT MODULE ...................................................................................................................... 1-12

Color Code ....................................................................................................................................... 1-13

CONTROL CODE MODULE.................................................................................................................... 1-14

Control Code Module (CCM) Bay Slot............................................................................................... 1-14

AD Manchester Code Terminal.......................................................................................................... 1-14

SEC RS-422 Code Terminal ............................................................................................................... 1-14

Color Code ....................................................................................................................................... 1-15

SPECIFICATIONS.................................................................................................................................... 1-16

Electrical Specifications..................................................................................................................... 1-16

Mechanical Specifications ................................................................................................................. 1-16

Environmental Specifications............................................................................................................ 1-16

Computer Interface Requirements (Minimum)................................................................................. 1-17

Video Input Specifications ................................................................................................................. 1-17

Video Output Specifications .............................................................................................................. 1-17

Regulatory ........................................................................................................................................... 1-17

Product Codes..................................................................................................................................... 1-18

CHAPTER 2 INSTALLATION ...................................................................................... 2-1

Before You Begin.................................................................................................................................... 2-1

Verification of Equipment and Unpacking ....................................................................................... 2-1

Remove Module Retainer ................................................................................................................... 2-1

About Connection Diagrams ............................................................................................................. 2-1

Single MP168 Bay Components ........................................................................................................ 2-2

Dual MP168 Bay Components ........................................................................................................... 2-2

Installation............................................................................................................................................... 2-3

Required Tools and Equipment......................................................................................................... 2-3

Recommended Video Cable............................................................................................................... 2-3

Recommended Data Cable................................................................................................................. 2-3

MOUNTING .............................................................................................................................................. 2-4

POWER & DATA CONNECTION ............................................................................................................ 2-5

Primary Power Line Cord ................................................................................................................... 2-5

Primary Power Connections .............................................................................................................. 2-5

Redundant Power Supply .................................................................................................................. 2-5

Redundant Power Supply Connections ........................................................................................... 2-6

CENTRAL PROCESSING UNIT MODULE CONNECTIONS ................................................................. 2-7

RS-232 Connections ........................................................................................................................... 2-7

CONTROL CODE MODULE CONNECTIONS ........................................................................................ 2-8

SensorNet Connections ..................................................................................................................... 2-8

AD Manchester Control Code Configurations ................................................................................. 2-8

Daisy Chain Configuration................................................................................................................. 2-8

Star Configuration ........................................................................................................................... 2-9

RS-422 Connections ........................................................................................................................... 2-10

VIDEO INPUT MODULE CONNECTIONS .............................................................................................. 2-12

VIM-1 Connections.............................................................................................................................. 2-12

VIM-2 to VIM-3 Connections............................................................................................................... 2-13

Dual Bay Video Input Connections................................................................................................2-13

Ribbon Cable Connections ............................................................................................................ 2-13

VIM-4 Modules and Loop Panels (Single Bay) ................................................................................. 2-14

Ribbon Cable Connections ............................................................................................................ 2-14

VIM-4 Modules and Loop Panels (Dual Bay) .................................................................................... 2-15

VIDEO OUTPUT MODULE CONNECTIONS .......................................................................................... 2-16

Video Output Connections ............................................................................................................. 2-16

VIDEO OUTPUT MODULE JUMPER SETTINGS................................................................................... 2-17

Single Bay Configuration ................................................................................................................... 2-17

Dual Bay Configuration ...................................................................................................................... 2-17

DUAL BAY CONNECTIONS ................................................................................................................... 2-18

EXTERNAL SYNCHRONIZER CONNECTION ....................................................................................... 2-19

Setting Vertical Phase ........................................................................................................................ 2-19

CONNECTING PERIPHERALS AND ACCESSORIES .......................................................................... 2-20

Parallel.................................................................................................................................................. 2-20

Printer Connection.............................................................................................................................. 2-20

PC Connection .................................................................................................................................... 2-21

External System Controller Connection...........................................................................................2-23

APPENDIX A ...............................................................................................................A-1

DIMENSIONS FOR MP168 BAY ............................................................................................................. A-1

System Control Devices (less than 2.1m-7 feet from MP168)................................................................ A-2

AD2079/AD2088 Operator Keyboards ........................................................................................... A-2

System Control Devices (greater than 2.1m - 7 feet)............................................................................. A-3

AD2079/AD2088 Operator Keyboards ........................................................................................... A-3

System Control Devices (less than 2.1m - 7 feet) ................................................................................. A-4

ADTT Touch Tracker Operator Keyboard ..................................................................................... A-4

System Control Devices (greater than 2.1m - 7 feet)............................................................................. A-5

ADTT Touch Tracker Operator Keyboard ..................................................................................... A-5

System Expansion Devices ................................................................................................................... A-6

AD1691 Manchester Code Distributor to Receiver/Driver and Pan/Tilt/Zoom Unit...................... A-6

AD1981 RS-232 Port Expander .......................................................................................................... A-7

AD2091 Control Code Converter....................................................................................................... A-8

AD2096A Alarm Interface Unit ........................................................................................................... A-9

AD1641M Manchester Control Code Receiver/Driver ..................................................................... A-10

APPENDIX B ...............................................................................................................B-1

TROUBLESHOOTING ............................................................................................................................. B-1

Section 1- Video Troubleshooting..................................................................................................... B-2

Section 2- Switcher System Troubleshooting ................................................................................. B-3

APPENDIX C ...............................................................................................................C-1

SensorNet Communications ................................................................................................................. C-1

SensorNet Connection on the MP168 CCM...................................................................................... C-1

Attaching to SensorNet ...................................................................................................................... C-1

Network Design Considerations ....................................................................................................... C-2

Network Topologies ............................................................................................................................... C-3

Daisy Chain Link Guidelines.............................................................................................................. C-3

Backbone Link Guidelines ................................................................................................................. C-4

Star Link Guidelines ........................................................................................................................... C-5

Network Checkout .................................................................................................................................. C-5

APPENDIX D ...............................................................................................................D-1

INDEX ....................................................................................................................................................... D-1

PREFACE

Who Should Use This Manual

•

Engineers, customer engineers, and installers who want to learn how the American Dynamics MegaPower 168

(MP168) Matrix Switcher/Controller System operates.

Customer engineers and installers who want to learn how the system is installed and serviced.

How To Use This Manual

This manual is divided into the following sections:

The DESCRIPTION section provides an introduction to the MP168 Matrix Switcher/Controller System as well as

general information about the individual components that comprise the system. This section also includes the MP168

Matrix Switcher/Controller System specifications.

The INSTALLATION section provides basic information about preparing for the installation of the MP168 Matrix

Switcher/Controller System with topics such as what is needed to install the system, what considerations must be

examined when planning the installation, and general information that will aid the installers. This section also provides

the necessary procedures required to install the system and adapt it to the operational environment.

The APPENDIX section is divided into three sub-sections:

The TYPICAL CONNECTIONS sub-section provides detailed diagrams for connecting external devices to the

MP168 Matrix Switcher/Controller System.

The SERVICE AND TROUBLESHOOTING sub-section contains specific information regarding procedures

when attempting to diagnose a particular problem with the installation.

An INDEX is provided in this manual to aid in finding particular topics in a more timely fashion.

i

ii

Related Documents

Additional information relating to the MP168 Matrix Switcher/Controller System can be found within the following

documents:

MegaPower 168 System Administrator’s Manual Part Number 8000-0935-*

ADTT TouchTracker

™ Operator Keyboard Installation and Operation Manual

Part Number 8000-1657-*

AD2088 Operator Keyboard Installation and Operation Manual

Part Number 8000-1811-*

AD2079 Operator Keyboard Installation and Operation Manual

Part Number 8000-1810-*

* Suffix 01 - English

02 - French

03 - German

04 - Spanish

05 - Portuguese

Ordering Documents

Additional copies of this Installation and Service manual may be obtained from your Sensormatic sales representative.

The document number for this manual (English language) is 8000-0934-01.

Questions?

For questions that this manual does not address, call Technical Support at

1-800-507-6268

or

FAX: (845) 624-7685

DESCRIPTION

MP168 Matrix Switcher/Controller System

MegaPower 168 Matrix Switcher/

Controller System

CHAPTER 1

DESCRIPTION

In this chapter:

General Description .................................................................................... 1-1

Provides information regarding the design of the MegaPower168 Switcher/Controller

System as well as a description of the individual components that comprise a system.

Specifications ............................................................................................... 1-16

Provides detailed information about the MegaPower168 Switcher/Controller System and

components.

DESCRIPTION

MP168 Matrix Switcher/Controller System

DESCRIPTION

GENERAL DESCRIPTION

The MP168 Matrix Switcher/Controller System is

designed to support plug-in modules having a broad

range of functionality. Plug-in modules include a

Power Supply module, a Central Processing Unit

module, an optional Control Code module, Video Input

modules, and Video Output modules. Built-in

expansion capabilities permit the addition of a second

MP168 Bay to increase the number of video output

devices supported.

The MegaPower 168 Matrix Switcher/Controller

System (hereafter referred to as the MP168) is an

integrated CCTV matrix switching and control system

for CCTV surveillance systems with multiple video

inputs, outputs, and control stations. Video inputs are

typically provided by local or remote cameras and other

video sources. Video output is viewed on monitors, or

recorded on VCRs located at system control points.

In addition to providing video input and output

switching, the MP168 system can respond to alarms

and perform auxiliary switching for the control of

gates, doors, lights, etc. Depending on the control

requirements of a given application, various AD

keyboards and accessory devices can be used in concert

with the system bays, cameras, and monitors.

External communications to system devices can be

achieved through a variety of protocols, including

Manchester Control Code, RS-232, RS-422, and

External ARCNET. A parallel printer port is standard

with each MP168 system to provide hard copy of

operating parameters and alarm events.

As delivered, the MP168 Matrix Switcher/Controller

System is completely configured and ready for

mounting in standard EIA rack units, with video inputs

terminated in 75 ohms, requiring only system

interconnections, video input and output connections,

and any optional accessory connections prior to

operation.

I

N

O

U

T

O

U

T

O

U

T

O

U

T

I

N

I

N

I

N

I

N

I

N

O

U

T

O

U

T

LOOP

THROUGH

I

N

O

U

T

O

U

T

O

U

T

O

U

T

I

N

I

N

I

N

I

N

I

N

O

U

T

O

U

T

Figure 1-1 Standard Configuration of MP168 Video Matrix Switching System

Administrator

Computer

Video Inputs 1 - 168

Video Outputs 7 - 12

Video Outputs 1-6

1-1

DESCRIPTION

MP168 Matrix Switcher/Control System

MP168 Bay Construction

MP168 Bay Modules

Each Module in the Bay is comprised of two

components:

Bay Housing - Front

The MP168 Bay is a custom made enclosure that

houses all of the components of the MP168 Matrix

Switcher/Controller. The front section of the Bay

houses the Printed Circuit Cards and the Front Panel.

One rack mount ear is affixed to each side of front

section (see Figure 1-2).

•

A Circuit Card (see below), and

A Rear Panel Assembly, consisting of:

Rear Panel and Rear Panel Circuit Card

(see page 1-3)

Front Panel

Circuit Cards

The Front Panel of the MP168 Bay features a view

window that permits visual monitoring of the UOP

(Unit Operating Properly) LEDs.

The Circuit Card for each module resides in the front

section of the MP168 Bay (see Figure 1-2). The Circuit

Card communicates to its corresponding Rear Panel

Assembly through a Mid-Plane. The Mid-Plane has

integral mating connectors in the front and in the rear

for each circuit card to plug into.

The Front Panel is held on by two captive screws for

quick removal during service operations.

Figure 1-2 - MP168 Switcher/Controller Front Panel and Bay

Circuit

Card

UOP LED

Captive

Screw

View

Window

Rack Mount Ears

Front Panel

MP168 Bay

1-2

MP168 Matrix Switcher/Controller System

DESCRIPTION

Bay Housing - Rear

The rear of the MP168 Bay houses the various Rear

Panel Assemblies that provide the versatility of the

MP168 Switcher/Controller (see Figure 1-3).

Rear Panel Assembly

Each MP168 module includes a Rear Panel Assembly

consisting of a Rear Panel and a Rear Panel Circuit

Card.

Rear Panel

The Rear Panel provides the entry/exit point for signals

from and to external peripheral devices as well as for

inter-bay communications.

Figure 1-3 - MP168 Bay and Rear Panels

MP168 Bay

Rear Panel

Rear Panel Assembl

y

1-3

DESCRIPTION

MP168 Matrix Switcher/Control System

POWER SUPPLY MODULE

The Power Supply Module (PSM) features an on-

board switching power supply that converts 90-240 volt

(47-63Hz) AC input power to ±8 volt DC power for

internal use by all system modules.

In the event of a loss of AC power, the Power Supply

Module has provisions to accept an ±8 Volt DC

redundant power source (not provided). An internal

monitoring circuit senses the loss of primary voltage

and automatically switches to the redundant power

supply, effectively eliminating any disturbance to

system functions.

The Power Supply module also provides a 0-5VDC

square wave “Line-Sync” signal that is in-phase and

synchronized to the primary power source to

automatically synchronize internal switching functions.

•

The Power Supply Module always resides in

slot R (determined by the lettered slot

designation screening on the front and rear bay

surface). See Figure 1-4A.

The front and rear sections of the Power

Supply Module are identified with a RED

color code dot affixed to the respective

section.

The Power Supply Module includes the following

components:

PSM Circuit Card

PSM Rear Panel Assembly consisting of:

Rear Panel and Rear Panel Circuit Card

Power Supply Module Features

A. Printer Port

The Rear Panel of the PSM provides a parallel port

(labeled A in Figure 1-4D) to connect to a system

printer for outputting operating events and setups.

B. Data Line BNC Connectors

The PSM provides high-speed data line BNC

terminals (labeled B in Figure 1-4D). The IN/OUT

terminals are for looping to external system bays.

The second data line OUT terminal provides

MP168 data line outputs to external devices such

as Control Code distributors and receivers.

Front View

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

R

Rear View

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

R

Figure 1-4A - MP168 PSM Slot Designations (Front & Rear)

PSM Installation Slot (R)

Figure 1-4B - PSM Circuit Card In Bay

PSM Circuit

Card

1-4

MP168 Matrix Switcher/Controller System

DESCRIPTION

Color Code

C. ARCNET Connector

The Power Supply Module features a red code marker

on the upper portion of the panel for easy identification

when performing system modifications or service.

An RJ-45 jack (labeled C in Figure 1-4D) is

provided to enable bay-to-bay communications via

the ARCNET protocol.

Color Code - RED

EXT

SYNC

OUT

DATALI NE

IN

REDUNDANT

SUPPLY

PRI NTER

PORT

ARCNET

LOOP

THROUGH

OUT

CLASS 2 WIRI NG ONLY

Figure 1-4D - Power Supply Module Rear Panel

B

E

F

D

C

B

A

D. Primary Power Connector

The primary source of power for the MP168

Switcher enters the bay through the Primary Power

Connector (labeled D in Figure 1-4D). A mating

line cord that is tailored specifically to the national

or regional electrical requirements of the intended

installation site is provided with the module.

E. Redundant Power Connector

The Power Supply Module is capable of supporting

a redundant power supply to prevent a total loss of

power to the MP168 Switcher in instances where

problems occur with the primary power source.

The Power Supply Module provides a 10-pin port

(labeled E in Figure 1-4D) for the connection of a

redundant power supply.

F. External Sync I/O Connectors

An external AC Line synchronizer may be used

with the MP168 Switcher in cases where

synchronous line phasing is desired for the entire

system and all related components. An external

sync signal enters the MP168 Bay through the EXT

SYNC terminal (labeled F in Figure 1-4D) on the

Power Supply Module.

Note: The External Sync OUT connector is not a sync

signal generated by the MP168 Switcher; it

merely provides a looping path for an external

synchronizer routed through the Switcher.

Figure -1 4C - PSM Rear Panel Assembly In Bay

1-5

DESCRIPTION

MP168 Matrix Switcher/Control System

CENTRAL PROCESSING

UNIT MODULE

The Central Processing Module includes the following

components:

The Central Processing Unit Module (CPM) performs

all switching control functions for single and dual bay

configurations, provides on-screen setup programming

menus (refer to the System Administrator Manual), and

dictates the functions of other modules in the MP168

system.

The Central Processing Unit module supports standard

switching system input devices including keyboards,

printers, external computers, alarms, and auxiliaries.

The CPM module is always installed next to the Power

Supply Module (see Figure 1-5A).

NOTE: Only one Central Processing Unit Module

is required for dual bay configurations.

An ARCNET repeater resident in the

Power Supply Module provides direct

control functions to the second bay.

•

CPM Circuit Card

CPM Rear Panel Assembly consisting of:

Rear Panel and Rear Panel Circuit Card

Figure 1-5B CPM Circuit Card In Bay

CPM Circuit

Card

The Central Processing Module always resides

in slot Q, determined by the lettered slot

designation screening on the front and rear bay

surface (see Figure 1-5A).

The front and rear sections of the Central

Processing Module are identified with a

PURPLE color code dot affixed to the

respective section.

Front View

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

R

Rear View

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

R

Figure 1-5A - MP168 CPM Slot Designations (Front & Rear)

CPM Installation Slot (Q)

1-6

MP168 Matrix Switcher/Controller System

DESCRIPTION

Connections

Color Code

The CPM module is provided with ten RJ-45 modular

jacks for connecting compatible devices to the MP168

system.

The Central Processing Unit Module features a purple

code marker on the upper portion of the panel for easy

identification when performing system modifications or

service.

The first two RJ-45 modular jacks are dedicated for use

with ETHERNET (jack 1) and ARCNET (jack 2)

communications (see Figure 1-5D).

Figure 1-5D - Central Processing Module Rear

Panel Port Designations

Color Code - PURPLE

RJ-45 Jack 1 = ETHERNET Port

RJ-45 Jack 2 = ARCNET

RJ-45 Jack 3 = RS-232 Port #1

RJ-45 Jack 4 = RS-232 Port #2

RJ-45 Jack 5 = RS-232 Port #3

RJ-45 Jack 6 = RS-232 Port #4

RJ-45 Jack 7 = RS-232 Port #5

RJ-45 Jack 8 = RS-232 Port #6

RJ-45 Jack 9 = RS-232 Port #7

RJ-45 Jack 10 = RS-232 Port #8

Default PC connection port

Jacks 3 through 10 are dedicated for use with RS-232

compatible devices such as AD1981 Port Expanders,

modems, control keyboards, Personal Computers, etc.

Jack 10 (RS-232 Port 8) is the default port for

connecting a Personal Computer to the MP168. Two

RS-232 cables with RJ45 connectors and terminal

blocks are provided with each MP168 System.

Program Monitor

A Program Monitor BNC connector provides video

output to a dedicated monitor for basic system setup

and control functions or can be connected directly to a

VIM video input and switched to any system monitor.

Figure 1-5C CPM Rear Panel Assembly In Bay

CPM Rea

r

Panel

1-7

DESCRIPTION

MP168 Matrix Switcher/Control System

VIDEO INPUT MODULES

• The MP168 VIM-4 module is used in single

and dual bay applications. VIM-4 modules are

used in conjunction with external Looping

Panels to route video signals into, through, and

out of the MP168 Bay. VIM-4 modules may

reside in slots A through O.

The MP168 Video Input Modules (VIMs) function by

recognizing the presence of a video signal and then

switching the signal to the Central Processing Unit.

Then, the video is switched to the appropriate Video

Output Module.

All video inputs to the MP168 system are connected to

the application specific VIM Rear Panels (see Figure 1-

6B). The VIM card receives switching instructions

from user keyboards, GUIs, and external systems with

the appropriate protocol.

In the MP168 Switching System, there are four types of

Video Input Modules (VIM-1, VIM-2, VIM-3, and

VIM-4). The Circuit Cards in all four VIM modules

are identical, only the Rear Panel Assemblies differ,

according to their intended function.

•

The front and rear sections of all MP168 VIM

modules are identified with a BLUE color

code dot affixed to the respective section.

Each MP168 Video Input Module includes the

following components:

VIM Circuit Card

VIM Rear Panel Assembly consisting of:

Application Specific Rear Panel and Rear

Panel Circuit Card

An MP168 VIM-1 module provides 12 direct

input channels for video sources. The MP168

Bay supports a maximum of 15 VIM-1

modules. VIM-1 modules can reside in slots A

through O determined by the letter slot

screening on the front and rear bay surface

(see Figure 1-6A).

• MP168 VIM-2 and VIM-3 modules are used

in dual bay applications. Installed in pairs and

joined by ribbon cables, VIM-2/VIM-3

module pairs provide 12 direct input channels

(6 per module) for video sources. VIM-

2/VIM-3 pairs can reside in slots A through O.

Figure 1-6B - MP168 VIM Rear

Panels

VIM-1 Rea

r

VIM-3 Rea

r

VIM-4 Rea

r

VIM-2 Rea

r

Front View

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

R

Rear View

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

R

Figure 1-6A - MP168 VIM Slot Designations (Front & Rear)

Video Input Module Installation Slots

(A through O)

1-8

Page is loading ...

American Dynamics MegaPower 168 Installation and Service Manual

This manual is also suitable for

American Dynamics MegaPower 168 Installation and Service Manual

Related papers

Other documents