American Dynamics AD168 Installation guide

Brand
American Dynamics
Model
AD168
Type
Installation guide
American Dynamics
Technical Support Center
1-800-442-2225 (USA)
(914) 624-7640
Quick Reference Card, PSM, AD168 8000-0949-05, Revision B
Power Supply Module
Installation Instructions
AD168 SYSTEM COMPONENT(S)
FRONT SIDE (SEE REAR FOR FURTHER INSTRUCTIONS)
About This Component
The AD168 Power Supply Module (PSM) is an on-board
switching power supply that converts 90-240 volt (47-63Hz)
AC input power to ±8 volt DC power for internal use by all
system modules.
The PSM is shipped with a detachable AC input line cord
appropriate for the national and local electrical requirements
of the operating location.
NOTES:
• The PSM resides in slot R of the AD168 bay.
• The front and rear sections of the PSM are identified
with a RED color code dot.
• A factory-set shorting jumper is used to determine
whether the PSM is used in single or dual bay
applications. The replacement PSM must use the
same jumper settings as are observed on the module
being replaced.
• Avoid static discharge by using proper grounding
methods before handling circuit cards.
• The AC line cord should be connected to the PSM
only after all service work has been completed.
Receiving the Component
At the time that the AD168 system component is delivered,
verify that the shipment is complete.
Inspect the box and packing to ensure that there has been no
damage during shipment. If damage is found, notify the
shipping agency and contact your sales representative.
Unpack the component in a secure location and lay out the
individual parts in an orderly fashion.
This kit includes the PSM Replacement Instructions (this
document) and either of two PSM components:
• AD168PSM-PC (PSM front module)
• AD168PSM-BP (PSM rear panel)
Required Tools and Equipment
• Small flat-head screwdriver
• Small Phillips head screwdriver
Front View
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
Rear View
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
Figure 1 - AD168 Slot Designation (Front & Rear)
EXT
SYNC
OUT
DATALI NE
IN
OUT
IN
CLASS
2
WIRI NG
ONLY
REDUNDANT
SUPPLY
PRI NTER
PORT
ARCNET
LOOP
THROUGH
OUT
Figure 2 - PSM Rear Panel
PSM Installation Slot (R)
PSM Rear Panel
RED Color Code Dot
Sensormatic CCTV Systems Division
1 Blue Hill Plaza
PO Box 1710
Pearl River, New York 10965
Quick Reference Card, PSM, AD168 8000-0949-05, Revision B
AD168 SYSTEM COMPONENT(S)
REAR SIDE (SEE FRONT FOR INITIAL INSTRUCTIONS)
Power Supply Module
Installation Instructions
PSM Module Replacement
!
CAUTION!
Disconnect the primary power source from the
AD168 bay before starting any work.
1. Loosen the two front cover retaining screws and remove
the cover.
2. If this is a replacement, locate and remove the old Power
Supply Module (PSM).
3. Note the position of the jumper labeled J10.
4. Remove the new PSM from its wrapping.
5. Compare the J10 jumper settings to the old PSM. Adjust if
appropriate.
6. Hold the PSM by the isolation handle with one hand and
support it from the bottom with the other hand. Avoid
touching circuit card components.
7. Begin to insert the module by placing the lower end of the
card into slot R.
8. Verify that the top of the card is also aligned with slot R.
9. Gently push the module until it stops.
10. Apply gentle, steady pressure to the isolation handle until
the connector moves into position in its mating receptacle.
11. Replace the front cover when service is complete.
PSM Rear Panel Replacement
1. Remove the top and bottom panel retaining screws and
remove the old rear panel from the bay.
2. Remove the new PSM rear panel from its wrapping.
3. Hold the rear panel by the connector strip with one hand
and support the attached circuit card from the bottom with
the other hand. Avoid touching circuit card components.
4. Begin to insert the rear panel by placing the lower end of
the card into slot R.
5. Verify that the top of the rear panel card is also aligned
with slot R
6. Gently push the rear panel until it stops.
7. Apply gentle, steady pressure to the center of the connector
strip until the rear panel moves into position.
8. Replace the screws that hold the rear panel to the chassis.
9. Connect all system devices to the rear panel.
10. Re-connect the primary power source to the new PSM and
verify that the system is operating properly (if the UOP
LED does not flash after 1 minute, call Technical Support).
Figure 4 - PSM Rear Panel
Figure 3 - Power Supply Module in Front of Bay
Power Supply Module
  • Page 1 1
  • Page 2 2

American Dynamics AD168 Installation guide

Brand
American Dynamics
Model
AD168
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents