Legrand SWS Accessory Enclosure (HACCBOX) Installation guide

Brand: Legrand

Model: SWS Accessory Enclosure (HACCBOX)

Type: Installation guide

Installation Instructions

Inc.

HACCBOX

Low-voltage Component Enclosure

Installation and Setup

The HACCBOX is a surface-mounted accessory

enclosure for low-voltage components.

The HACCBOX was designed to simplify remote

mounting of lighting control accessories that must be

connected to a network dataline, such as in a

Smartwired

™

Switching System.

The HACCBOX is a complete enclosure consisting of:

•Tub

• Hinged “shoebox” cover with locking latch mechanism

• Interior frame for mounting a power supply

• Accessory plate with DIN rail

• Circuit board providing dataline and power connections

A power supply (HPSM series), if required, must be

ordered separately.

Features

• Complete enclosure for accessory devices

• DIN rail for mounting up to two dataline modules

• Mounting plate with pre-drilled holes for non-DIN

rail devices

• Connections for Global Dataline, Local Dataline and

power supply

• Frame for mounting power supply

• Hinged cover with locking latch

• UL Listed

Before proceeding, read the instructions on this

sheet. For an overview of the entire system and

the documentation forms, refer to the other sections

of the SMARTWIRED SWITCHING SYSTEM

INSTALLATION AND OPERATION MANUAL.

If you have any questions, call our Service Team

at: 888-852-2778.

Panel Division 888-852-2778 INHACC 091301

HACCBOX Low-voltage Component Enclosure — Installation and Setup

CAUTION: Make sure all power is off

before wiring. Do not energize wiring

until the unit is fully assembled.

Conform to all applicable codes.

Environment

• Mount in an indoor area

• 32 to 131°F (0 to 55°C)

• 95% relative humidity, non-condensing

Mounting

The unit may be mounted anywhere on

the dataline, subject to any dataline

length limitations. (Refer to dataline

speciﬁcations)

The unit is shipped assembled. Before

mounting the tub, it is necessary to

remove the interior. Unscrew the two

nuts and washers securing the interior to

the studs at the top and bottom of the

tub (see A in photo top right), and slide

the interior forward and out.

The tub should be level, plumb and

rigidly installed with hardware sufﬁcient

to hold 50 lbs. minimum. With the cover

open, the product label should be in the

lower right corner of the inside cover.

(see HACCBOX view on the front page)

Install the Power Supply

(if required)

Before reinstalling the interior in the tub,

mount the power supply to the opening

in the interior frame (see B in photo top

right). Tighten the captive screws to hold

the unit in place. Plug the 5-pin yellow

low-voltage connector to the power

terminal on lower left of the circuit board

(J1 in photo right).

Install the Interior

Slide the interior back into the tub and

secure it to the studs with the screws

and washers.

Wire the power supply as shown to the

right. Refer to the installation instructions

for the HPSMxxx power supply for more

information.

Make sure that all line- and low-voltage

wiring is conﬁned to the appropriate

areas (see photo above).

Connect Dataline De-

vices

Mount dataline devices such as the

HCLK8SS Network Clock or HUSM8SS

Universal Switch Interface Module to the

DIN rail in the low voltage section of the

accessory box. Connect the dataline

cable supplied with the unit to the 4-pin

Local Dataline connector as shown to

the left. Dataline devices may also be

connected to the Local Dataline termi-

nals using HDLW4(P) dataline wire.

Wire Other Low-Voltage

Devices

If the accessory box is being used for

non-dataline devices, simply mount the

device(s) to the plate in the low-voltage

section, using the pre-drilled holes

provided. Wire as directed in the unit’s

instruction manual.

For service or assistance call our

Service Team at 888-852-2778

LINE-VOLTAGE

SECTION

LOW-VOLTAGE

SECTION

DIN RAIL

GLOBAL DATALINE CONNECTIONS

LOCAL DATALINE CONNECTIONS

POWER

SUPPLY

CONNECTIONS

PRE-DRILLED HOLES FOR

MOUNTING ACCESSORIES

Legrand SWS Accessory Enclosure (HACCBOX) Installation guide

Legrand SWS Accessory Enclosure (HACCBOX) Installation guide

Legrand SWS Accessory Enclosure (HACCBOX) Installation guide

Related papers

Other documents