Rockwell Automation Allen-Bradley 5094-OW8IXT User manual

FLEX 5000 Standard and Safety Digital I/O Modules

Catalog Numbers 5094-IB16, 5094-IB16XT, 5094-IB16S, 5094-IB16SXT, 5094-OB16, 5094-OB16XT, 5094-OB16S,

5094-OB16SXT, 5094-OW8I, 5094-OW8IXT

User Manual

Original Instructions

Important User Information

Read this document and the documents listed in the additional resources section about installation, configuration, and

operation of this equipment before you install, configure, operate, or maintain this product. Users are required to

familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws,

and standards.

Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are

required to be carried out by suitably trained personnel in accordance with applicable code of practice.

If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may

be impaired.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from

the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and

requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or

liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or

software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation,

Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

Labels may also be on or inside the equipment to provide specific precautions.

WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous

environment, which may lead to personal injury or death, property damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property

damage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the consequence.

IMPORTANT Identifies information that is critical for successful application and understanding of the product.

SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerous

voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that surfaces may

reach dangerous temperatures.

ARC FLASH HAZARD: Labels may be on or inside the equipment, for example, a motor control center, to alert people to

potential Arc Flash. Arc Flash will cause severe injury or death. Wear proper Personal Protective Equipment (PPE). Follow ALL

Regulatory requirements for safe work practices and for Personal Protective Equipment (PPE).

Rockwell Automation Publication 5094-UM001C-EN-P - April 2019 3

Table of Contents

Preface

Summary of Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Manual Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Graphics Indicate Feature Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Terminology. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Additional Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Chapter 1

Digital I/O Module Operation

in a Logix 5000 Control System

Controller and Software Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . 17

Controller Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Firmware and Software Compatibility. . . . . . . . . . . . . . . . . . . . . . . 18

Secure Access to the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Types of Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Module Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Ownership . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Multiple Owners of FLEX 5000 Input Modules . . . . . . . . . . . . . 22

Configuration Changes in an Input Module

with Multiple Owners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Construct a 5094 FLEX 5000 I/O System. . . . . . . . . . . . . . . . . . . . . . . 24

FLEX 5000 I/O System Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Configuration via Logix Designer Application . . . . . . . . . . . . . . . . . . . 25

Connections for Standard I/O Modules. . . . . . . . . . . . . . . . . . . . . . . . . 26

Requested Packet Interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Connection Types Available with FLEX 5000

Standard I/O Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Data Types Available with FLEX 5000 Standard

I/O Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Connections for Safety I/O Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

‘Configured By’ Options for Safety I/O Modules. . . . . . . . . . . . . 29

Data Types Available with FLEX 5000 Safety I/O Modules. . . 30

Requested Packet Interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Connection Over an EtherNet/IP Network . . . . . . . . . . . . . . . . . . . . . 32

Input Module Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Trigger Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Output Module Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Listen Only Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Protected Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Considerations Specific to Safety Modules . . . . . . . . . . . . . . . . . . . . . . 36

Single-channel or Dual-channel Mode. . . . . . . . . . . . . . . . . . . . . . . 37

Use with Safety Controllers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Determine Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Obtain Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Safety Application Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

4 Rockwell Automation Publication 5094-UM001C-EN-P - April 2019

Table of Contents

Safe State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Configuration Signature and Ownership . . . . . . . . . . . . . . . . . . . . 42

Reset FLEX 5000 I/O Safety Modules to Out-of-Box State . . . 43

Chapter 2

Common Digital I/O Module

Features

Input Module Compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Output Module Capability. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Producer/Consumer Communication . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Module Data Quality Reporting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Software Configurable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Fault and Status Reporting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Module Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Module Inhibiting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Electronic Keying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Module Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Chapter 3

Input Module Features Data Transfer at RPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Software Configurable Input Filters and Delays. . . . . . . . . . . . . . . . . . 54

Field Power Loss Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Fault and Status Reporting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Chapter 4

Output Module Features Features Specific to All FLEX 5000 Output Modules . . . . . . . . . . . . 57

Output State Change Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Configurable Point-level Output State in Program Mode or

Fault Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Connection Fault Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Output Behavior Immediately After a Connection Fault. . . . . . 59

Output State Once Connection Is Re-established . . . . . . . . . . . . 59

Forcing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Enable Forces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Disable or Remove a Force . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Check Force Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

GSV Instruction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Data Echo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Field Power Loss Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Fault and Status Reporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Features Specific to Only Standard and Safety Solid-state

Output Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

No Load Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Short-Circuit Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Thermal Shutoff . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Features Specific to Only 5094-OB16 and

5094-OB16XT Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Time-scheduled Output Control . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Rockwell Automation Publication 5094-UM001C-EN-P - April 2019 5

Table of Contents

Use a MAOC Instruction with a 5094-OB16 or

5094-OB16XT Standard Output Module . . . . . . . . . . . . . . . . . . . 67

Feature Specific to Only 5094-OW8I and

5094-OW8IXT Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Isolated Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Chapter 5

Safety I/O Module Features Safety Input Module Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Safety Application Suitability Levels . . . . . . . . . . . . . . . . . . . . . . . . 71

Input Modules in CIP Safety Systems . . . . . . . . . . . . . . . . . . . . . . . 72

Use Test Output with a Safety Input . . . . . . . . . . . . . . . . . . . . . . . . 73

Single-channel Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Safety Input Fault Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Safety Input Delay. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Safety Output Module Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Safety Application Suitability Levels . . . . . . . . . . . . . . . . . . . . . . . . 79

Output Module in CIP Safety Systems . . . . . . . . . . . . . . . . . . . . . . 80

Safety and Safety Pulse Test Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Single-channel Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Dual-channel Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Surge Capability of Safety Output . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Safety Output Fault Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Fault and Status Reporting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Chapter 6

Configure the Standard Module Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Create a New Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Discover Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

New Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Edit the Module Configuration Common Categories . . . . . . . . . . . . 93

General Category. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

Connection Category. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Module Info Category . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

Edit 5094-IB16 Module Configuration Categories. . . . . . . . . . . . . . . 97

Counters Category . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

Points Category . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

Events Category . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

Time Sync Category . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

Edit 5094-OB16 Module Configuration Categories. . . . . . . . . . . . . 103

Points Category . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103

Edit 5094-OW8I Module Configuration Categories . . . . . . . . . . . . 104

Points Category . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

View the Module Tags. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

6 Rockwell Automation Publication 5094-UM001C-EN-P - April 2019

Table of Contents

Chapter 7

Configure and Replace Safety

Modules

Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

Create a New Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

New I/O Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

Edit the Module Configuration Common Categories . . . . . . . . . . . 110

General Category. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

Connection Category. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113

Safety Category. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

Module Info Category . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115

Edit the 5094-IB16S or

5094-IB16SXT Module Configuration Categories. . . . . . . . . . . . . . 115

Input Points Category . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115

Test Output Points Category. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116

Edit the 5094-OB16S or 5094-OB16SXT Module

Configuration Category . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117

View the Module Tags. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117

Replace a Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118

Set the SNN Manually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119

Reset to Out-of-Box Configuration . . . . . . . . . . . . . . . . . . . . . . . . 120

Replace a Module in a Logix 5000 System . . . . . . . . . . . . . . . . . . 121

Appendix A

Troubleshoot Your Module SA Power Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124

Module Status Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

FLEX 5000 Digital Input Modules Status Indicators . . . . . . . . . . . . 126

FLEX 5000 Output Modules Status Indicators . . . . . . . . . . . . . . . . . 127

FLEX 5000 Safety Input Modules Status Indicators. . . . . . . . . . . . . 129

FLEX 5000 Safety Output Modules Status Indicators . . . . . . . . . . . 130

Use the Logix Designer Application for Troubleshooting. . . . . . . . 131

Warning Signal in the I/O Configuration Tree . . . . . . . . . . . . . 131

Status and Fault Information in Module

Properties Categories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132

Logix Designer Application Tag Editor. . . . . . . . . . . . . . . . . . . . . 136

Appendix B

Module Tag Definitions Tag Name Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138

Access the Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138

5094-IB16 Module Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139

Configuration Tags. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139

Input Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140

Output Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143

Event Input Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144

Event Output Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145

5094-IB16S and 5094-IB16SXT Module Tags . . . . . . . . . . . . . . . . . 147

Input Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147

Test Output Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148

Rockwell Automation Publication 5094-UM001C-EN-P - April 2019 7

Table of Contents

Safety Output Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148

5094-OB16 Module Tags. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149

Configuration Tags. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149

Input Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150

Output Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151

5094-OB16S and 5094-OB16SXT Module Tags . . . . . . . . . . . . . . . 152

Input Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152

Safety Output Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153

5094-OW8I Module Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153

Configuration Tags. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153

Input Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154

Output Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154

Appendix C

Application/Wiring Examples

for Safety I/O Modules

5094-IB16S and 5094-IB16SXT Module Wiring Diagrams. . . . . . 156

5094-OB16S and 5094-OB16SXT Module Wiring Diagrams . . . 161

Appendix D

Safety Data for I/O Modules FLEX 5000 I/O Safety Input Module Safety Data . . . . . . . . . . . . . . 164

FLEX 5000 I/O Safety Output Module Safety Data. . . . . . . . . . . . . 164

8 Rockwell Automation Publication 5094-UM001C-EN-P - April 2019

Table of Contents

Notes:

Rockwell Automation Publication 5094-UM001C-EN-P - April 2019 9

Preface

This manual describes how to use FLEX 5000™ standard and safety I/O

modules in Logix 5000™ control systems.

Make sure that you are familiar with the following:

• Use of a controller in a Logix 5000 control system

• Use of an EtherNet/IP™ network, if the digital I/O modules are installed

in a remote location from the controller that is accessible via the

EtherNet/IP network

• Use of safety systems

• Studio 5000 Logix Designer® environment

Summary of Changes

This manual was revised to add information about FLEX 5000 I/O safety

modules. This table indicates where new content exists in the manual.

Manual Conventions

Within this manual, we simplified product names and added product icons for

your ease of use.

We u se standard module to indicate a module that does not have functional

safety capability. We use safety module to indicate a module with functional

safety capability (catalog numbers ending in “S” or “SXT”). Further, we use

FLEX 5000 I/O module to indicate when a concept or task applies to both the

standard and safety digital I/O modules.

Topic Page

Added safety catalog numbers 5094-IB16S, 5094-IB16SXT, 5094-OB16S, 5094-OB16SXT Throughout

Added Chapter 5

, Safety I/O Module Features 71

Added Chapter 7, Configure and Replace Safety Modules 107

Added Appendix C, Application/Wiring Examples for Safety I/O Modules

155

Added Appendix D, Safety Data for I/O Modules 163

10 Rockwell Automation Publication 5094-UM001C-EN-P - April 2019

Preface

Graphics Indicate

Feature Support

Throughout this manual, graphics appear with section titles to indicate the

digital I/O modules that support the feature that is described in that section.

If both standard and safety modules support a feature, you see icons for both

types.

If only one type of module, standard or safety, supports a feature, you see only

one type of icon.

Rockwell Automation Publication 5094-UM001C-EN-P - April 2019 11

Preface

Terminology

This table defines terms that are used in this manual.

Abbreviation Full Term Definition

1oo2 One out of Two Identifies the programmable electronic controller architecture.

CIP™ Common Industrial Protocol An industrial communication protocol that is used by Logix 5000-based automation

systems on EtherNet/IP™, ControlNet®, and DeviceNet® communication networks.

CIP Sync™ Common Industrial Protocol Synchronization CIP Sync provides the increased control coordination needed for control applications

where absolute time synchronization is vital to achieve real-time synchronization

between distributed intelligent devices and systems.

CIP Safety™ Common Industrial Protocol – Safety Certified SIL-rated version of CIP.

— Connection Logical communication channel for communication between nodes. Connections are

maintained and controlled between masters and slaves.

CL Claim Limit The maximum safety integrity level (SIL) that can be achieved.

DC Diagnostic Coverage The ratio of the detected failure rate to the total failure rate.

EDS Electronic Data Sheet, A template that is used in RSNetWorx™ software to display the configuration

parameters, I/O data profile, and connection-type support for a given I/O module.

RSNetWorx software uses these simple text files to identify products and commission

them on a network.

EN European Norm. The official European Standard.

ESS Energy Storage System Used for backup for memory retention at powerdown on Compact GuardLogix® 5380

controllers. The ESS is inside the controller and cannot be removed.

GSV Get System Value A ladder logic instruction that retrieves specified controller status information and

places it in a destination tag.

MTTF Mean Time To Failure The length of time that a device or other product is expected to remain reliable in

operation.

— Multicast The transmission of information from one sender to multiple receivers.

NAT Network Address Translation The translation of an Internet Protocol (IP) address to another IP address on another

network.

ODVA Open DeviceNet Vendor Association A nonprofit association of vendors that are established for the promotion of CIP

networks.

PC Personal computer Computer that is used to interface with and control a Logix-based system via the

Studio 5000® environment.

PFD Probability of Failure on Demand The average probability of a system to fail to perform its design function on demand.

PFH Average frequency of a dangerous failure per hour The probability of a system to have a dangerous failure occur per hour.

PL Performance Level ISO 13849-1 safety rating.

— Proof test Periodic test that detects failures in a safety-related system so that, if necessary, the

system can be restored to an as-new condition or as close as practical to this condition.

— Safety (devices) Devices or portions of devices that have functional safety capability.

SIL Safety Integrity Level A relative level of risk-reduction provided by a safety function, or to specify a target

level of risk reduction.

SNN Safety Network Number A unique number that identifies a section of a safety network.

SRT Safety Reaction Time A consideration of delays or latencies within the safety system.

SSV Set System Value A ladder logic instruction that sets controller system data.

— Standard (devices) Devices or portions of devices that do not have functional safety capability.

— Unicast The transmission of information from one sender to one receiver.

12 Rockwell Automation Publication 5094-UM001C-EN-P - April 2019

Preface

Additional Resources

These documents contain additional information concerning related products

from Rockwell Automation.

Table 1 - Additional Resources

Resource Description

FLEX 5000 I/O Modules Specifications Technical Data,

publication 5094-TD001

Provides specifications for FLEX 5000 EtherNet/IP

adapters and FLEX 5000 modules.

FLEX 5000 EtherNet/IP Adapters with RJ45 Ports

Installation Instructions, publication 5094-IN001

Describes how to install and wire the 5094-AENTR,

5094-AENTRXT, 5094-AEN2TR, and 5094-AEN2TRXT

EtherNet/IP adapters.

FLEX 5000 EtherNet/IP Adapters with SFP Support

Installation Instructions, publication 5094-IN002

Describes how to install and wire the 5094-AENSFPRXT

and 5094-AEN2SFPRXT EtherNet/IP adapters.

FLEX 5000 Digital 16-point Sinking Input Modules

Installation Instructions, publication 5094-IN003

Describes how to install and wire the 5094-IB16 and

5094-IB16XT digital input modules.

FLEX 5000 Digital 16-point Sourcing Output Modules

Installation Instructions, publication 5094-IN004

Describes how to install and wire the 5094-OB16 and

5094-OB16XT digital output modules.

FLEX 5000 Digital 8-point Isolated Relay Output Modules

Installation Instructions, publication 5094-IN005

Describes how to install and wire the 5094-OW8I and

5094-OW8IXT digital output modules.

FLEX 5000 Analog 8-channel Current/Voltage Input

Modules Installation Instructions, publication

5094-IN006

Describes how to install and wire the 5094-IF8 and

5094-IF8XT analog input modules.

FLEX 5000 Analog 8-channel Current/Voltage Output

Modules Installation Instructions, publication

5094-IN007

Describes how to install and wire the 5094-OF8 and

5094-OF8XT analog output modules.

FLEX 5000 Analog 8-channel Current/Voltage/RTD/

Thermocouple Input Modules Installation Instructions,

publication 5094-IN008

Describes how to install and wire the 5094-IY8 and

5094-IY8XT analog input modules.

FLEX 5000 High-speed Counter I/O Modules Installation

Instructions, publication 5094-IN009

Describes how to install and wire the 5094-HSC and

5094-HSCXT high-speed counter I/O modules.

FLEX 5000 Terminal Base Assembly Modules Installation

Instructions, publication 5094-IN010

Describes how to install and wire the terminal base

assemblies for the FLEX 5000 system.

FLEX 5000 Digital 16-point Sinking Safety Input

Modules Installation Instructions, publication

5094-IN012

Describes how to install and wire the 5094-IB16S and

5094-IB16SXT digital safety input modules.

FLEX 5000 Digital 16-point Sourcing Safety Output

Modules Installation Instructions, publication

5094-IN013

Describes how to install and wire the 5094-OB16S and

5094-OB16SXT digital safety output modules.

FLEX 5000 Analog I/O Modules User Manual, publication

5094-UM002

Describes how to configure, operate, and troubleshoot

FLEX 5000 analog I/O modules.

FLEX 5000 High-speed Counter I/O Modules User

Manual, publication 5094-UM003

Describes how to configure, operate, and troubleshoot

FLEX 5000 high-speed counter modules.

CompactLogix 5380 Controllers User Manual,

publication 5069-UM001

Describes how to configure, operate, and troubleshoot

CompactLogix™ 5380 controllers.

EtherNet/IP Communication Modules in 5000 Series

Control Systems User Manual, publication ENET-UM004

Describes how to configure, operate, and troubleshoot

the FLEX 5000 EtherNet/IP adapters.

Integrated Architecture and CIP Sync Configuration

Application Technique, publication IA-AT003

Provides information about CIP Sync technology and

how to synchronize clocks within the Rockwell

Automation Integrated Architecture® system.

Electronic Keying in Logix5000 Control Systems

Application Technique, publication LOGIX-AT001

Describes how to use electronic keying in Logix 5000

control system applications.

Logix5000 Controllers Tasks, Programs, and Routines

Programming Manual, publication 1756-PM005

Provides more information on event tasks and event

task configuration.

Position-based Output Control with the MAOC

Instruction, publication 1756-AT017

Describes how to configure time-scheduled output

control with the MAOC instruction.

Rockwell Automation Publication 5094-UM001C-EN-P - April 2019 13

Preface

You can view or download publications at

http://www.rockwellautomation.com/global/literature-library/overview.page

.

To order paper copies of technical documentation, contact your local

Allen-Bradley distributor or Rockwell Automation sales representative.

Industrial Automation Wiring and Grounding

Guidelines, publication 1770-4.1

Provides general guidelines for installing a

Rockwell Automation industrial system.

Product Certifications website,

http://www.rockwellautomation.com/

rockwellautomation/certification/overview.page

Provides declarations of conformity, certificates, and

other certification details.

SISTEMA software utility,

http://marketing.rockwellautomation.com/safety/en/

Sistema_Download

The Rockwell Automation SISTEMA data library is

available for download, together with a link to the

SISTEMA download site.

Table 1 - Additional Resources

14 Rockwell Automation Publication 5094-UM001C-EN-P - April 2019

Preface

Notes:

Rockwell Automation Publication 5094-UM001C-EN-P - April 2019 15

Chapter 1

Digital I/O Module Operation

in a Logix 5000 Control System

Topic Page

Controller and Software Compatibility 17

Before You Begin 25

Secure Access to the System 19

Types of Modules 19

Module Overview 20

Ownership 22

Construct a 5094 FLEX 5000 I/O System 24

Configuration via Logix Designer Application 25

Connections for Standard I/O Modules 26

Connections for Safety I/O Modules 28

Connection Over an EtherNet/IP Network 32

Input Module Operation 32

Output Module Operation 33

Listen Only Mode 35

Protected Operations 36

Considerations Specific to Safety Modules 36

Use with Safety Controllers 37

IMPORTANT You cannot use FLEX 5000™ I/O modules with all Logix 5000™ controllers.

For example, you can use FLEX 5000 I/O modules with CompactLogix™ 5380

and ControlLogix® 5580 controllers but not with CompactLogix 5370 and

ControlLogix 5570 controllers.

You can use FLEX 5000 I/O modules with Logix 5000 controllers as

remote I/O modules only.

Throughout this publication, the term Logix 5000 controller refers to the

controllers with which you can use FLEX 5000 I/O modules in a given

capacity. The term does not refer to all Logix 5000 controllers.

For the most current information on the Logix 5000 controllers with which

you can use FLEX 5000 I/O modules, see the product description

at http://www.ab.com

.

16 Rockwell Automation Publication 5094-UM001C-EN-P - April 2019

Chapter 1 Digital I/O Module Operation in a Logix 5000 Control System

Logix 5000 controllers use FLEX 5000 standard and safety I/O modules to

control devices in a control system. The controllers access the modules over an

EtherNet/IP™ network. FLEX 5000 I/O modules use terminal base (TB)

assemblies to connect field-side wiring.

FLEX 5000 I/O modules use the Producer/Consumer network communication

model. This communication is an intelligent data exchange between modules and

other system devices in which each module produces data without first being

polled.

You use FLEX 5000 I/O modules as remote I/O modules that are accessible via

an EtherNet/IP network. The modules are installed to the right of a FLEX 5000

EtherNet/IP adapter.

Logix 5000 controllers can exchange data with the modules over the network.

Figure 1

shows a standard controller with standard I/O modules. Standard

controllers do not support safety I/O modules.

Figure 1 - FLEX 5000 Standard I/O Modules in a Logix 5000 Control System

STATUS

NET

LINK 1

LINK 2

5094-AENTR

EtherNet/IP

™

Adapter

FLEX 5000

TM

I/O

PRP

DLR

POWER

X100

X10

X1

IP ADDRESS

STATUS

POWER

DIGITAL 16 INPUT 24 VDC

5094-IB16

1

TB3

FLEX 5000

TM

I/O

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

STATUS

POWER

DIGITAL 16 OUTPUT 24 VDC

5094-OB16

1

2

TB3

FLEX 5000

TM

I/O

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

STATUS

POWER

RELAY 8 OUTPUT ISOLATED

5094-OW8I

2

TB3W

FLEX 5000

TM

I/O

0 1 2 3 4 5 6 7

5069-L340ERM

EtherNet/IP Network

5094 Standard I/O

5094-AENTR

Rockwell Automation Publication 5094-UM001C-EN-P - April 2019 17

Digital I/O Module Operation in a Logix 5000 Control System Chapter 1

Figure 2 shows a safety controller with standard and safety I/O modules. Safety

controllers support both standard and safety I/O modules.

Figure 2 - FLEX 5000 Safety I/O Modules in a Logix 5000 Control System

Controller and Software

Compatibility

Controller and programming software compatibility requirements apply when

you use FLEX 5000 standard and safety I/O modules. A module type and how it

is used affect which requirements apply.

You must also consider Logix Designer application version requirements when

you design your system. For example, you can use FLEX 5000 safety I/O

modules with only version 32 or greater of the Logix Designer application.

Controller Compatibility

Compatibility between Logix 5000 controllers and FLEX 5000 I/O modules

varies based on module type, that is, whether the module is standard or safety.

While you must pair safety I/O with a safety controller, you can also pair

standard I/O with a safety controller. For example, ControlLogix 5580

controllers are compatible with FLEX 5000 standard I/O modules.

GuardLogix® 5580 controllers are compatible with FLEX 5000 standard and

safety I/O modules.

STATUS

NET

LINK 1

LINK 2

5094-AENTR

EtherNet/IP

™

Adapter

FLEX 5000

TM

I/O

PRP

DLR

POWER

X100

X10

X1

IP ADDRESS

SIL2 CPU

5069-L3100ERMS2

Compact GuardLogix

SA Power

MOD Power

STATUS

POWER

RELAY 8 OUTPUT ISOLATED

5094-OW8I

2

TB3W

FLEX 5000

TM

I/O

0 1 2 3 4 5 6 7

STATUS

POWER

SAFETY DIGITAL 16 INPUT 24 VDC

5094-IB16S

5

TB3I

FLEX 5000

TM

I/O

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

STATUS

POWER

5094-OB16S

5

1

TB3I

FLEX 5000

TM

I/O

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

SAFETY DIGITAL 16 OUTPUT 24 VDC

5094 Standard I/O5094 Safety I/O5094-AENTREtherNet/IP Network5069-L5380

18 Rockwell Automation Publication 5094-UM001C-EN-P - April 2019

Chapter 1 Digital I/O Module Operation in a Logix 5000 Control System

Firmware and Software Compatibility

Tabl e 2 describes the module compatibility requirements when you use

FLEX 5000 I/O standard and safety modules with Logix 5000 controllers.

IMPORTANT You must use adapter firmware version 3.011 or later with standard I/O

firmware version 2.011 and safety I/O modules.

Table 2 - FLEX 5000 I/O Standard and Safety Modules Controller and Software Compatibility Requirements

Controllers Logix Designer

Modules System Cat. Nos. Application Version

Standard Modules

5094-IB16, 5094-IB16XT,

5094-OB16, 5094-OB16XT,

5094-OW8I, 5094-OW8IXT

CompactLogix 5380 5069-L320ER, 5069-L340ERM 31.00.00 or later

5069-L306ER, 5069-L306ERM, 5069-L310ER, 5069-L310ERM, 5069-L310ER-NSE,

5069-L310ERS2, 5069-L320ERM, 5069-L330ER, 5069-L330ERM, 5069-L340ER

31.00.00 or later

5069-L350ERM, 5069-L380ERM, 5069-L3100ERM 31.00.00 or later

Compact GuardLogix 5380 5069-L306ERMS2, 5069-L306ERS2, 5069-L310ERS2, 5069-L310ERMS2,

5069-L320ERS2, 5069-L320ERMS2, 5069-L330ERS2, 5069-L330ERMS2,

5069-L340ERS2, 5069-L340ERMS2, 5069-L350ERS2, 5069-L350ERMS2,

5069-L380ERS2, 5069-L380ERMS2, 5069-L3100ERS2, 5069-L3100ERMS2

31.00.00 or later

ControlLogix 5580 1756-L83E, 1756-L85E 31.00.00 or later

1756-L81E, 1756-L82E, 1756-L84E 31.00.00 or later

GuardLogix 5580 1756-L81ES, 1756-L82ES, 1756-L83ES, 1756-L84ES 31.00.00 or later

Safety Modules

5094-IB16S, 5094-IB16SXT,

5094-OB16S, 5094-OB16SXT

Compact GuardLogix 5380 5069-L306ERMS2, 5069-L306ERS2, 5069-L310ERS2, 5069-L310ERMS2,

5069-L320ERS2, 5069-L320ERMS2, 5069-L330ERS2, 5069-L330ERMS2,

5069-L340ERS2, 5069-L340ERMS2, 5069-L350ERS2, 5069-L350ERMS2,

5069-L380ERS2, 5069-L380ERMS2, 5069-L3100ERS2, 5069-L3100ERMS2

32.00.00 or later

GuardLogix 5580 1756-L81ES, 1756-L82ES, 1756-L83ES, 1756-L84ES 32.00.00 or later

Rockwell Automation Publication 5094-UM001C-EN-P - April 2019 19

Digital I/O Module Operation in a Logix 5000 Control System Chapter 1

Secure Access to the System

To secure access to the [device] by authorized users only, consider these options:

• Password helps protect the source and execution of the control program

• Remove the key from the controller

• Deploy EtherNet/IP devices in accordance with recommended

architectures and concepts. See the Converged Plantwide Ethernet

(CPwE) Design and Implementation Guide, publication ENET-TD001

.

• Implement physical barriers, such as locked cabinets

To secure access to the system, consider these options:

• Follow industry best practices to harden your personal computers and

servers, including anti-virus/anti-malware and application whitelisting

solutions.

The recommendations are published at the Rockwell Automation

technical support center in Knowledgebase article Rockwell Automation

Customer Hardening Guidelines, #546987. The technical support center is

available at: https://rockwellautomation.custhelp.com/

• Develop and deploy backup and disaster recovery policies and procedures.

Test backups on a regular schedule.

• Minimize network exposure for all control system devices and systems, and

confirm that they are not accessible from the Internet.

• Locate control system networks and devices behind firewalls and isolate

them from the business network.

• Subscribe to the Rockwell Automation Security Advisory Index,

Knowledgebase article KB54102, so you have access to information about

security matters that affect Rockwell Automation products.

Types of Modules

Tabl e 3 describes the types of FLEX 5000 I/O modules.

Table 3 - FLEX 5000 Standard and Safety Digital I/O Modules

Cat. No.

(1)

(1) XT modules can operate in extreme environments while non-XT modules cannot.

Description

5094-IB16, 5094-IB16XT 18…32V DC 16-point, sink input module

5094-IB16S, 5094-IB16SXT 18…32V DC 16-point sinking safety input module

5094-OB16, 5094-OB16XT 18…32V DC 16-point, sourcing output module

5094-OB16S, 5094-OB16SXT 18…32V DC 16-point sourcing safety output module

5094-OW8I, 5094-OW8IXT 5…240V AC /125V DC 8-point, isolated normally open relay output module

STATUS

POWER

SAFETY DIGITAL 16 INPUT 24 VDC

5094-IB16S

5

TB3I

FLEX 5000

TM

I/O

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

STATUS

POWER

DIGITAL 16 INPUT 24 VDC

5094-IB16

1

TB3

FLEX 5000

TM

I/O

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Safety Modules

Standard Modules

20 Rockwell Automation Publication 5094-UM001C-EN-P - April 2019

Chapter 1 Digital I/O Module Operation in a Logix 5000 Control System

Module Overview

Figure 3 shows the parts of an example FLEX 5000 standard I/O module.

Figure 3 - Example FLEX 5000 Standard I/O Module

STATUS

POWER

DIGITAL 16 INPUT 24 VDC

5094-IB16

1

TB3

FLEX 5000

TM

I/O

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

2

1

3

53 4

Table 4 - FLEX 5000 Standard I/O Module Parts

Item Description

1 Status indicators - Displays the status of communication, module health, and input/output

devices. Indicators help with troubleshooting anomalies

2 Release lever - Disengages the latching hooks to allow removal of the module from the

terminal base assembly

3 Module keying - Indicates the keying position the terminal base assembly must be configured

to before installing the module

4 Terminal base - Indicates the type of terminal base assembly to use with the module

5 Latching hooks - Securely installs FLEX 5000 modules on the terminal base assembly

Page is loading ...

Rockwell Automation Allen-Bradley 5094-OW8IXT User manual

This manual is also suitable for

Rockwell Automation Allen-Bradley 5094-OW8IXT User manual

Related papers

Other documents