Anova L1369A Assembly Instruction

Brand: Anova

Model: L1369A

Type: Assembly Instruction

anovafurnishings.com

888.535.5005 tel

TOOLS NEEDED:

• 11/16" Open-end or Box-end Wrench

• Ratchet with 11/16" Socket

• 7/16" Open-end Wrench

• Flat Head Screw Driver

• Level

Assembly Instructions

Streetside

L1369A - Streetside 6' Contour Bench with Divided Seating

COMPONENT PARTS:

ASSEMBLY HARDWARE: All hardware is stainless steel.

(4) 7/16"-14

Hex Nut

(4) 7/16" Lock

Washer

(4) 7/16" Flat

Washer

(8) 1/4"-20

Acorn Nut

(8) 1/4" Flat

Washer

(8) 1/4"-20 X 3/4"

Slotted Bolt

(4) Plastic

Foot

(8) Adhesive

Strip

(1) Contour Bench Seat (1) Right Side

Bench End

(1) Le Side

Bench End

ASSEMBLY:

Inspect the shipping container contents for damage and to

determine that all components and hardware are present.

The assembly is a two-person operation.

2. Lay all parts on a so work surface or on the shipping

packaging to prevent damage to nish.

3. Apply two adhesive tape strips to one of the plastic

rectangular feet. Then rmly apply the plastic foot to the

metal foot on one of the bench ends aligning the holes in

each. Repeat this step until the remaining plastic feet and

adhesive strips have been applied onto both bench ends.

NOTE: Before assembling the nuts to the bolts, it is

recommended that a light oil or petroleum jelly be applied to

the screw threads.

(2) Armrests

7/16" Hex Nut

7/16" Lock Washer

7/16" Flat Washer

6. Align an armrest with the mounting holes on the bench. Insert

a 1/4"-20 slotted bolt with a 1/4" at washer through the back

of the bench. Place another washer on the bolt from the front

of the bench and secure a 1/4"-20 acorn nut onto the bolt.

Repeat this process with the remaining hardware on both

armrests.

Leave the hardware nger tight so adjustments can be made

during assembly.

7. Tighten the bench end hardware using the 11/16" wrench and 11/16" socket, while checking the seat

surface with a level; minor adjustments can be made while tightening the hardware to make the

seat level. Tighten the armrest hardware with a at head screw driver and a 7/16" open-end wrench.

Front View

Back View

1/4" Flat Washer

1/4" Acorn Nut

1/4"-20 Slotted Bolt

1/4" Flat Washer

Mounting Stud

7/16" Hex Nut

7/16" Lock Washer

7/16" Flat Washer

Mounting Studs

Hole near middle of

bench seat denotes

backrest portion

Hole near bend of bench

seat denotes seat portion

4. Align the mounting studs in one of the bench ends with the

holes in the appropriate end of the bench seat.

5. Insert the mounting studs on the bench end through the

mounting holes in the bench seat. Install a 7/16" at washer,

then a 7/16" lock washer and a 7/16" hex nut on each of the

mounting studs.

Repeat this step for the opposite bench end.

Leave the hardware nger tight so that adjustments can be

made during assembly and to level the bench.

Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.

11/05/2019

VIEW A-A

SCALE 1:14

SECTION B-B

SCALE 1:14

A A

B B

A A

B B

THIRD ANGLE PROJECTION

TOLERANCES UNLESS NOTED:



1 X.X



.5 X.XX ± .25 X.XXX ± .125

X.XXXX ± .0625 X.XXXXX ± .03125

X.XXXXXX



.015625 ANGULAR ± 1°

ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES

OR BENDS ARE 90 UNLESS OTHERWISE SPECIFIED

DO NOT SCALE DRAWING

PRINT IS FOR FABRICATION ONLY. ALL SURFACES

MAY EXPAND BY .125 .0625 DURING COATING.

211 North Lindbergh Blvd.

St. Louis, MO 63141

888.535.5005 tel

314.754.0835 fax

specify@anovafurnishings.com

anovafurnishings.com

DRAWN

???

SIZE

BL1369A-SPEC-REV-001

DATE 9/25/2019 SCALE

.09375:1

SHEET

DWG NO

TITLE

D. METZ

THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF

ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.

THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.

REV

1 OF

???

THIS DRAWING IS FOR PROTOTYPE OR TOOLING

USE ONLY. DO NOT USE FOR PRODUCTION.

1 ???? ????-??? ??/??/13

33.45

19.11

4.00

23.58

25.57

75.25

72.25

1.50

23.31 22.50

75.50



.50

(4 PLCS)

16.83

73.63

FOOT MOUNT

73.63"

16.83"

Ø.50"

(4 PLCS)

Assembly and Replacement Parts

Armrest

Right Side Bench End Le Side Bench End

Contour Bench Seat

8. Aer two weeks, retighten all hardware.

Anova L1369A Assembly Instruction

Anova L1369A Assembly Instruction

Anova L1369A Assembly Instruction

Related papers

Other documents