DANLERS DP1D 10VDC SB Installation guide

Brand
DANLERS
Model
DP1D 10VDC SB
Type
Installation guide

DANLERS DP1D 10VDC SB is a dimmer switch designed to control the brightness of lights connected to a 1-10V high-frequency dimmable ballast. It features a push-push 2-way switch and a rotary control knob, allowing you to switch the lights on and off and adjust their brightness at the control or with another 2-way switch or intermediate switches. Each gang or module can control up to twenty 1-10V ballasts, assuming each ballast draws 1mA (or less) through the voltage control lines.

DANLERS DP1D 10VDC SB is a dimmer switch designed to control the brightness of lights connected to a 1-10V high-frequency dimmable ballast. It features a push-push 2-way switch and a rotary control knob, allowing you to switch the lights on and off and adjust their brightness at the control or with another 2-way switch or intermediate switches. Each gang or module can control up to twenty 1-10V ballasts, assuming each ballast draws 1mA (or less) through the voltage control lines.

installation notes
Advice from: DANLERS Limited, Vincients Road, CHIPPENHAM, Wiltshire, SN14 6NQ, United Kingdom.
Telephone: +44 (0)1249 443377 Fax: +44 (0)1249 443388
E-mail: [email protected] Web: www.danlers.co.uk
Company Registered Number 2570169 VAT Registration Number 543 5491 38
INS 150 - Instructions DP1D 10VDC SB.indd27/05/15
The DP1D 10VDC SB is suitable for controlling the brightness of a load controlled by a 1-10VDC high frequency
dimmable ballast.
The control comprises a push-push 2-way switch and a rotary control function. This enables the lights to be
switched on and off at the selected brightness, either at the control or by another 2-way switch or intermediate
switches.
1. Read these notes before commencing work.
2. Incaseofdoubtconsultaqualiedelectricalcontractor.
3. Make sure power is switched off from the circuits you are working on by removing appropriate fuses, or
switching off appropriate isolating switches.
4. The power supply to the ballast is switched by the 1 or 2-way switch terminals marked L1, L2, and C.
5. The circuit diagram is as below:-
6. The knob controls the brightness of the load via the 1-10Vdc separate terminal block on the dimmer
which is connected by 2 wires to a double terminal block on the ballast. The terminals marked L1
and L2 allow the option of 2-way circuit switching.
7. Each gang / module can control up to twenty 1-10V ballasts., assuming each ballast draws 1mA
(or less) through the voltage control lines.
8. Total load including ballasts, lamps plus other load must not exceed the following:
6 amps (1500W) Incandescent or mains halogen lamps (recommended with integral safety fuse)
4 amps (1000W) Electronic or wire wound transformers.
Fluorescent lamps (high frequency or soft start)
 2amps(500W) 2amps(500W)ofCFL,2Dlamps,LEDDriversandLEDlampsandttings.
1 amp (250W) Most metal halide lamps and fans.
 Minimumload2Wresistive,suitableformostenergysavinglamps,LEDsandemergencyttings.
DP1D 10VDC SB DIMMER for a single HF ballast
DIMMER
1-10VDC
+-
L1
L2
0
C
BALLAST
optional
2 way switch
optional
intermediate
switches
N
L
  • Page 1 1

DANLERS DP1D 10VDC SB Installation guide

Brand
DANLERS
Model
DP1D 10VDC SB
Type
Installation guide

DANLERS DP1D 10VDC SB is a dimmer switch designed to control the brightness of lights connected to a 1-10V high-frequency dimmable ballast. It features a push-push 2-way switch and a rotary control knob, allowing you to switch the lights on and off and adjust their brightness at the control or with another 2-way switch or intermediate switches. Each gang or module can control up to twenty 1-10V ballasts, assuming each ballast draws 1mA (or less) through the voltage control lines.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents