2. DANLERS
  3. RESLOADE

DANLERS RESLOADE Installation guide

  • I've reviewed the installation notes for the DANLERS RESLOADE Resistive Load and understand its purpose is to eliminate lamp flicker when dimming non-resistive loads. The document outlines installation procedures, troubleshooting, and precautions. I'm ready to assist with any questions you have about RESLOADE.
  • What is the purpose of RESLOADE?
    Where should the RESLOADE be installed?
    How is RESLOADE connected for direct mains dimmable lamps?
Installation notes
DANLERS Limited, Vincients Road, CHIPPENHAM, Wiltshire, SN14 6NQ, UK.
Telephone: +44 (0)1249 443377 Fax: +44 (0)1249 443388
E-mail: [email protected] Web: www.danlers.co.uk
Company Registered Number 2570169 VAT Registration Number 543 5491 38
Products available from DANLERS
• PIRoccupancyswitches•Daylightlinkeddimmers•Manualhighfrequencydimmers
• Photocells • Radio remote controls • Time lag switches • Outdoor security switches
• Dimmers•Heating,ventilationandair-conditioningcontrols•Bespoke/O.E.M.products
Please call for more information or a free catalogue, or visit our website.
Pleaseensurethemostrecenteditionoftheappropriatelocalwiringregulationsareobserved
andsuitableprotectionisprovidede.g.6ampsovercurrent,1kVovervoltage.Pleaseensure
thatthisdeviceisdisconnectedfromthesupplyifaninsulationtestismade.
Thisproductiscoveredbyawarrantywhichextendsto5yearsfromthedateofmanufacture.
Precautions and Warranty
Resistive Load
RESLOADE
DANLERSRESLOADE,resistiveload,canbeusedtotrytoeliminatelamp
instabilityandickerwhendimmingnon-resistiveloadssuchasmains
directlydimmableLED lamps, compactuorescentlamps or dimmable
transformers. The RESLOADE is designed for DANLERS Grid trailing
edgedimmers(DQDGD)whendimmingLEDlampsalthoughitmaybe
suitableforusewithothermanufacturersdimmerswhen dimmingLED
lamps.InappropriateuseoftheRESLOADEmayinvalidatethewarranty.
For direct mains dimmable lamps the RESLOADE is connected at
asuitablelighttting,in parallel across the load,betweenthedimmed
variableliveandneutral.
For mains dimmable transformerstheRESLOADEisconnectedacross
theprimary(variablemainsinput)sideofthetransformer.
TheRESLOADEisdesignedtobeplacedintotheceilingvoidandcan
be passed through a 63mm diameter cutout, the typical size for down
lighters,asshownbelow.
TheRESLOADEhasaneffectiveloadof10Wandanoperatingtemperature
of approximately 40°C above ambient. It should be installed where air
owisnotrestricted.Itshouldnotbecoveredbyinsulatingmaterialsor
positionednearanyheatsourcesorheatsensitiveobjects.
08/10/12 INS708RESLOADE
1.Please read these notes carefully before commencing work.
 Incaseofdoubtpleaseconsultaqualiedelectrician.
2.Make sure the power is isolated from the circuit.
TheRESLOADEwiresshouldbeconnectedasshown:
2 uncoded wires:
 VariableLive
Neutral
3.Oncethewiringhasbeencompletedandveried,switchonthe
supply and test the operation,
Lamp still ickers:
•Loadnotdimmableormoreresistiveloadmayneedtobeadded,
 usestandardresistivelightbulbstoassestheextraloadneeded.
Load
L
N
230 VAC
V
RESLOADE
L
Dimmer
Troubleshooting
End view
Plan view
130
60
RESLOADE fits through a 63mm diameter hole
60
Variable Live
Neutral
Installation procedure
Installation notes
DANLERS Limited, Vincients Road, CHIPPENHAM, Wiltshire, SN14 6NQ, UK.
Telephone: +44 (0)1249 443377 Fax: +44 (0)1249 443388
E-mail: [email protected] Web: www.danlers.co.uk
Company Registered Number 2570169 VAT Registration Number 543 5491 38
Products available from DANLERS
• PIRoccupancyswitches•Daylightlinkeddimmers•Manualhighfrequencydimmers
• Photocells • Radio remote controls • Time lag switches • Outdoor security switches
• Dimmers•Heating,ventilationandair-conditioningcontrols•Bespoke/O.E.M.products
Please call for more information or a free catalogue, or visit our website.
Pleaseensurethemostrecenteditionoftheappropriatelocalwiringregulationsareobserved
andsuitableprotectionisprovidede.g.6ampsovercurrent,1kVovervoltage.Pleaseensure
thatthisdeviceisdisconnectedfromthesupplyifaninsulationtestismade.
Thisproductiscoveredbyawarrantywhichextendsto5yearsfromthedateofmanufacture.
Precautions and Warranty
Resistive Load
RESLOADE
DANLERSRESLOADE,resistiveload,canbeusedtotrytoeliminatelamp
instabilityandickerwhendimmingnon-resistiveloadssuchasmains
directlydimmableLED lamps, compactuorescentlamps or dimmable
transformers. The RESLOADE is designed for DANLERS Grid trailing
edgedimmers(DQDGD)whendimmingLEDlampsalthoughitmaybe
suitableforusewithothermanufacturersdimmerswhen dimmingLED
lamps.InappropriateuseoftheRESLOADEmayinvalidatethewarranty.
For direct mains dimmable lamps the RESLOADE is connected at
asuitablelighttting,in parallel across the load,betweenthedimmed
variableliveandneutral.
For mains dimmable transformerstheRESLOADEisconnectedacross
theprimary(variablemainsinput)sideofthetransformer.
TheRESLOADEisdesignedtobeplacedintotheceilingvoidandcan
be passed through a 63mm diameter cutout, the typical size for down
lighters,asshownbelow.
TheRESLOADEhasaneffectiveloadof10Wandanoperatingtemperature
of approximately 40°C above ambient. It should be installed where air
owisnotrestricted.Itshouldnotbecoveredbyinsulatingmaterialsor
positionednearanyheatsourcesorheatsensitiveobjects.
08/10/12 INS708RESLOADE
1.Please read these notes carefully before commencing work.
 Incaseofdoubtpleaseconsultaqualiedelectrician.
2.Make sure the power is isolated from the circuit.
TheRESLOADEwiresshouldbeconnectedasshown:
2 uncoded wires:
 VariableLive
Neutral
3.Oncethewiringhasbeencompletedandveried,switchonthe
supply and test the operation,
Lamp still ickers:
•Loadnotdimmableormoreresistiveloadmayneedtobeadded,
 usestandardresistivelightbulbstoassestheextraloadneeded.
Load
L
N
230 VAC
V
RESLOADE
L
Dimmer
Troubleshooting
End view
Plan view
130
60
RESLOADE fits through a 63mm diameter hole
60
Variable Live
Neutral
Installation procedure
/