DANLERS DSSGD CB 10VDC Installation guide

Brand
DANLERS
Model
DSSGD CB 10VDC
Type
Installation guide

This manual is also suitable for

Installation notes
DANLERS Limited, Vincients Road, CHIPPENHAM, Wiltshire, SN14 6NQ, UK.
Telephone: +44 (0)1249 443377 Fax: +44 (0)1249 443388
E-mail: [email protected] Web: www.danlers.co.uk
Company Registered Number 2570169 VAT Registration Number 543 5491 38
Also available from DANLERS
• PIRoccupancyswitches•Daylightlinkeddimmers•Manualhighfrequencydimmers
• Photocells • Radio remote controls • Time lag switches • Outdoor security switches
• Dimmers•Heating,ventilationandair-conditioningcontrols•Bespoke/O.E.M.products
Please call for more information or a free catalogue, or visit our website.
ThisproductconformstoBSEN60669-2-1andBSEN55015:1993
Pleaseensurethemostrecenteditionoftheappropriatelocalwiringregulationsareobserved
andsuitableprotectionisprovidede.g.6ampsovercurrent,1kVovervoltage.Pleaseensure
thatthisdeviceisdisconnectedfromthesupplyifaninsulationtestismade.
Thisproductiscoveredbyawarrantywhichextendsto5yearsfromthedateofmanufacture.
Precautions and Warranty
1 to 10V ballast Dimmers (grid modules)
DSSGD MK 10VDC DSSGD CB 10VDC DSSGD EU 10VDC
These1to10Vsoftstartballastdimmersaresuitableforttinginto
the MK Grid Plus, Crabtree grid and Eurodata plates.
Thesoftstartfeaturerampsuptheballastcontrolvoltagewhichcan
greatlyincreaselamplife,particularlyforlowvoltagelamps.
Ashortpresswillswitchtheballastoffviatheswitchedlineoutputor
energisetheswitchedlineoutputandrestoretheballastcontrolvoltage
softlytoitsprevioussetting.
Aholdingpresswilldimthecontrolvoltageupanddowninturn.
Theballastcanbeswitchedanddimmedfromseverallocationsby
usingmainsrated,momentary,normally-openpush-to-makeswitches.
RemoteswitchesareavailablefrombothMK(K4885)andCrabtree
(4489).
DANLERS1-10Vdimmerscanpowerupto6amps(1500W)of:
• Highfrequencyballastdimmeduorescentlamps
• Highfrequencyballast(driver)dimmedLEDlampsetc.
Theycancontroluptotwenty1-10Vballasts.
• Assumingeachballastdraws1mA(orless)throughthevoltagecontrollines.
The1to10Vballastdimmersneedthefollowingminimumdepthwallboxes:
• DSSGDMK10VDC 35mm
• DSSGDCB10VDC 40mm
• DSSGDEU10VDC 35mm
06/03/12 INS910 DSSGD10VDC
Loading limits
Wall box depth
Fault nding
Lamp dims up and down constantly:
• Ensuremomentaryremoteswitcheshavebeenused
• Buttonpressedtoohardandjammed.Releasebutton
• Slavewiringmorethan10mlong.Useshieldedortwistedwiring.
Lamps do not dim:
• Disconnectthe1-10Vdimmer,thevoltageacrosstheterminalsof
the1-10vballastshouldbeat10Vandthelampshouldbeonfull,if
nottheremaybeaproblemwiththe1-10Vballast
• Reconnectthe1-10Vlinesandchecktoseeifthevoltagecanbe
variedviathedimmer.
Lamps do not switch off:
• Thedimmercanonlydimthelampsdowntoabout10%viathe
1-10Vlines,thelampsareswitchedoffbythedimmerremoving
thepowertotheballast.TheballastmustbeconnectedtotheSL
outputofthedimmer,notdirectlytoapermanentlivesupply.
• Whenswitchingverysmall,nonresistiveloads,suchasLED
drivers,theloadmayneedtobeaugmentedwithaCAPLOAD
devicewiredbetweentheSwitchedLineandNeutralatthetting.
1.Pleasereadthesenotescarefullybeforecommencingwork.
Incaseofdoubtpleaseconsultaqualiedelectrician.
Makesurethepowerisisolatedfromthecircuit.
2. The 1 to 10V ballast dimmer should be connected as:
L Live
N Neutral
SL SwitchedLineoutput(toballast)
R Mains-ratedmomentaryRemoteswitch(optional)
- - ofcontrolvoltage(toballast)
+ +ofcontrolvoltage(toballast)
3.Typicalwiringdiagramshownopposite.
4.Pleasenote:Failuretoconnecttheunitasshownmayresultindamage
to the product.
5.Pleasenote:IfusingRemotemomentaryswitch(es),eachconnecting
cable should be twin core of at least 1mm2 cross section and not
exceed 10 metres in length.
6.Oncethewiringhasbeencompletedandveried,switchonthesupply
and test the operation.
Typical wiring diagrams
1
ballast
10
1
ballast
10
1
ballast
10
control lines
L
230 VAC
Optional
mains rated,
normally open
push button (s)
L
N
N
SL
optional
other
load
* Total load of ballasts plus other load not more than 6 amps
R
1-10V
Dimmer
Installation procedure
  • Page 1 1
  • Page 2 2

DANLERS DSSGD CB 10VDC Installation guide

Brand
DANLERS
Model
DSSGD CB 10VDC
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents