DANLERS DP2D LED Installation guide

Brand: DANLERS

Model: DP2D LED

Category: Dimmers

Type: Installation guide

This manual is also suitable for

DANLERS DP2D LED is a 2-gang plated push and rotary LED dimmer. It is compatible with many reputable LED lamps and fittings and can dim within the following loading limits: 5W* minimum and 250W maximum per gang. Each dimmer switch has an adjustable trim spindle on the end of the dimmer module for designating the minimum dim level. The lamp can be switched from other locations by using standard 2-way and intermediate wall switches. It cannot be dimmed from another location and no other dimmer should be connected into the same switch circuit.

Installation notes

DANLERS Limited, Vincients Road, CHIPPENHAM, Wiltshire, SN14 6NQ, UK.

Telephone: +44 (0)1249 443377 Fax: +44 (0)1249 443388

E-mail: [email protected] Web: www.danlers.co.uk

Company Registered Number 2570169 VAT Registration Number 543 5491 38

Also available from DANLERS

• PIRoccupancyswitches•Daylightlinkeddimmers•Manualhighfrequencydimmers

• Photocells • Radio remote controls • Time lag switches • Outdoor security switches

• Dimmers•Heating,ventilationandair-conditioningcontrols•Bespoke/O.E.M.products

Please call for more information or a free catalogue, or visit our website.

This product conforms to BS EN 60669-2-1 and BS EN 55015:1993

Please ensure the most recent edition of the appropriate local wiring regulations are observed

and suitable protection is provided e.g. 6 amps over current, 1kV over voltage. Please ensure

that this device is disconnected from the supply if an insulation test is made.

This product is covered by a warranty which extends to 5 years from the date of manufacture.

DANLERS cannot guarantee that DP_D LED dimmers will successfully dim all LED lamps

and ttings.

The dimming performance of LED lamps and ttings may vary or not work at all when a mixture

of different types of lamps are tted in the circuit.

DANLERS cannot take responsibility for reduced lamp life to that claimed by lamp manufacturers.

Precautions and Warranty

Disclaimer

Plated rotary 2-way (push-on, push-off)

Dimmers for resistive loads

DP1D LED DP2D LED DP3D LED DP4D LED

DANLERSplatedpushandrotary2-way‘leadingedge’LEDdimmers

areavailableaseitheronegangortwogangdimmersonasquareplate

orasthreeorfourgangdimmersonarectangularplate.

Presstheknobtoturnthelamponandoff,rotateitclockwisetobrighten

thelampandanti-clockwisetodimit.

EachDP_DLEDhasanadjustabletrimspindleontheendofthedimmer

modulefordesignatingtheminimumdimlevel.

Thelampcanbeswitchedfromotherlocationsbyusingstandard2-way

andintermediatewallswitches.Itcannotbedimmedfromanotherlocation

andnootherdimmershouldbeconnectedintothesameswitchcircuit.

DANLERSplatedpushandrotaryLEDdimmersarecompatiblewith

manyreputableLEDlampsandttings.

DANLERScannotguaranteethatthesedimmerswillsuccessfullydim

ALLLEDlampsandttings.ThedimmingperformanceofLEDlamps

andttingsmayvarywhendifferenttypesoflampsarettedinthecircuit.

Each individual dimmer switch can dim within the following loading

limits,theyneedthefollowingwallboxdepthandaresuppliedonthe

followingplateshape.

Part Code Gang Min* Max Box depth Plate style

(per gang) (per gang)

DP1DLED 1 5W* 250W 35mm Square

DP2DLED 2 5W* 250W 35mm Square

DP3DLED 3 5W* 250W 35mm Rectangular

DP4DLED 4 5W* 250W 35mm Rectangular

*5W is the optimum minimum load on LED lamps tested by DANLERS.

However due to the variable nature of LED lamp drivers we cannot

guarantee 5W is the minimum with ALL LED lamps and ttings.

05/08/14 INS120DPxDLED

Lamp ickers:

• Adjustspindleonendofmoduletotrimtheminimumdimlevel

• Loadincompatiblewithleadingedgedimming

  ConsiderusingDANLERStrailingedge,QuietGriddimmer.

Rotary dimmer fails after some time:

• LEDlamporttinghasfailed.

Rotary dimmer ‘buzzes’:

• Thiscanoccurwithleadingedgedimmers,

  ConsiderusingDANLERStrailingedge,QuietGriddimmer.

Rotary dimmer gets warm:

• Thiscanoccurwithdimmers,especiallywhencontrollinglargeloads.

Troubleshooting

Installation procedure

1.Pleasereadthesenotescarefullybeforecommencingwork.

Incaseofdoubtpleaseconsultaqualiedelectrician.

Makesurethepowerisisolatedfromthecircuit.

2.TheLEDdimmershouldbeconnectedas:

L1 Live1(position1of2-wayswitch)

L2 Live2(position2of2-wayswitch)

V Common(commonof2-wayswitch).

3Typicalwiringdiagramsareshownopposite.

4.ShouldtheLEDlampsorttingsicker

whenthedimmerisinthelowerendofits

rangetheminimumdimlevelspindleshould

beturnedtothepointatwhichthelamp

stopsickering-seediagramopposite.

5.Once the wiring has been completed and

veried, switch on the supply and test the

operation.

Typical wiring diagrams

Existing 2 way and intermediate circuit

Nload

230 VAC

dimmer

load

230 VAC

dimmer

load

230 VAC

Either of the 2 way switches can be replaced:

Or:

Nload

230 VAC

dimmer

load

230 VAC

dimmer

load

230 VAC

Alternative 2 way and intermediate circuit

Either of the 2 way switches can be replaced:

Or:

DANLERS DP2D LED Installation guide

Brand: DANLERS

Model: DP2D LED

Category: Dimmers

Type: Installation guide

This manual is also suitable for

Download PDF

report

DANLERS DP2D LED Installation guide

This manual is also suitable for

DANLERS DP2D LED Installation guide

Related papers

Other documents