Furuno FAR-2117-BB User manual

www.furuno.co.jp

All brand and product names are trademarks, registered trademarks or

service marks of their respective holders.

MARINE RADAR/ARPA

FAR-2117/2127/2817/2827

FAR-2117-BB/2127-BB

Installation Manual

Comply with MSC.192(79)

TABLE OF CONTENTS

SAFETY IINSTRUCTIONS..................... i

EQUIPMENT LISTS...............................iii

SYSTEM CONFIGURATION .................vi

1. MOUNTING.....................................1-1

1.1 Antenna Unit.................................1-1

1.2 Monitor Unit..................................1-6

1.3 Control Unit................................1-10

1.4 Processor Unit............................1-15

2. WIRING........................................2-1

2.1 Interconnection.............................2-1

2.2 Antenna Unit.................................2-2

2.3 Monitor Unit..................................2-6

2.4 Processor Unit..............................2-7

2.5 Changing AC Power Specification of

Processor Unit ..........................2-12

3. SETTING AND ADJUSTMENT ....3-1

3.1 DIP Switch Setting .......................3-1

3.2 Initializing Tuning..........................3-2

3.3 Heading Alignment.......................3-3

3.4 Adjustment Sweep Timing............3-6

3.5

Suppressing Main Bang

...................3-7

3.6 Other Settings..............................3-8

3.7 Dual Radar Display

(non IMO-type only) ..................3-16

4. INSTALLING OPTIONAL

EQUIPMENT................................ 4-1

4.1 Gyro Converter GC-10.................4-1

4.2

Memory Card Interface Unit

..............4-9

4.3 DVI-RGB Conversion Kit

(for VDR connection) ..................4-12

4.4 Performance Monitor PM-31......4-15

4.5 BNC Connector Converter .........4-17

4.6 Junction Box...............................4-18

5. INPUT/OUTPUT DATA ................ 5-1

INSTALLATION MATERIALS,

ACCESSORIES,SPARE PARTS........A-1

OUTLINE DRAWINGS ......................D-1

INTERCONNECTION DIAGRAMS ...S-1

*00014745418**00014745418*

*

00014745418

*

00014745418

*

i

Mandatory Action

Prohibitive Action

WARNING

Indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation which, if not avoided,

can result in minor or moderate injury.

Warning, Caution

SAFETY INSTRUCTIONS

The operator and installer must read the applicable safety instructions before attempting to

install or operate the equipment.

WARNING

Radio Frequency Radiation Hazard

The radar antenna emits electromagnetic radio frequency (RF) energy which can be harmful,

particularly to your eyes. Never look directly into the antenna aperture from a close distance

while the radar ius in operation or eexpose yourself to the transmitting antenna at a close

distance. Distances at which RF radiation level of 100, 50 and 10 W/m are given in the table

below.

Note: If the antenna unit is installed at a close distance in front of the wheel house, your

administration may require halt of transmission within a certain sector of antenna revolution.

This is possible. Ask your FURUNO representive or dealer to provide this feature.

*

:

XN12AF: 4 ft, XN20AF: 6.5 ft, XN24AF: 8 ft

Model Transceiver Magnetron Antenna

100W/m

2

50W/m

2

10W/m

2

XN-12AF 0.3 m 1.2m 3.7 m

XN-20AF 0.1 m 0.7 m 2.2 m

XN-24AF 0.1 m 0.4 m 1.5 m

XN-12AF 0.9 m 2.6 m 9.0 m

XN-20AF 0.5 m 1.7 m 4.6 m

XN-24AF 0.2 m 1.0 m 3.3 m

MG4010/

MAF1425B

RTR-078

(X-12 kw)

FAR-2817/2117

FAR-2827/2127

RTR-079

(X-25 kw)

MG5436

2

DANGER

Indicates a potentially hazardous situation which, if not avoided,

will result in death or serious injury.

Wear a safety belt and hard hat when working on the antenna unit.

Serious injury or death can result if someone falls from the radar antenna

mast.

DANGER

*

1

ii

Be sure that the power supply is

compatible with the voltage rating of

the equipment.

Do not install the monitor unit,

processor unit or control unit where

they may get wet from rain or

water splash.

Fire or damage to the equipment can result

if a different cable is used.

Connection of an incorrect power supply

can cause fire or damage the equipment .

Use only the specified power cable.

Water in the units can result in fire,

electrical shock, or damage the equipment.

Attach securely protective

earth to the ship's body.

The protective earth

(grounding) is required to the

AC power supply to prevent

electrical shock.

CAUTION

Observe the following compass safe

distances to prevent deviation of a

magnetic compass:

Antenna Unit

(12 kw)

Standard

compass

2.15 m 1.40 m

Antenna Unit

(25 kw)

2.05 m 1.30 m

Monitor Unit

(MU-201CR)

1.55 m 1.00 m

Monitor Unit

(MU-231CR)

1.85 m 1.20 m

Processor

Unit (RPU-013)

1.35 m 0.85 m

Control Unit

(RCU-014)

0.30 m 0.30 m

Control Unit

(RCU-015)

0.95 m 0.60 m

Control Unit

(RCU-016)

0.65 m 0.45 m

Memory Card

Interface Unit

(CU-200)

0.90 m 0.60 m

Steering

compass

Switching Hub

(HUB-100)

1.00 m

0.60 m

Junction Box

(RJB-001)

1.10 m

0.70 m

Do not open the equipment

unless totally familiar with

electrical circuits and

service manual.

Only qualified personnel

should work inside the

equipment.

WARNING

Construct a suitable service platform

from which to install the antenna unit.

Serious injury or death can result if some-

one falls from the radar antenna mast.

Turn off the power at the mains switch-

board before beginning the installation.

Fire, electrical shock or serious injury can

result if the power is left on or is applied

while the equipment is being installed.

ELECTRICAL

SHOCK

HAZARD

iii

EQUIPMENT LISTS

Standard Supply

Name Type Code No. Qty Remarks

XN12AF-RSB096-078 -

FAR-2117/2117-BB/2817, 24 rpm,

1200 mm, W/CP03-24201

XN12AF-RSB097-078 -

FAR-2117/2117-BB/2817, 42 rpm,

1200 mm, W/CP03-24201

XN20AF-RSB096-078 -

FAR-2117/2117-BB/2817, 24 rpm,

2000 mm, W/CP03-19101

XN20AF-RSB097-078 -

FAR-2117/2117-BB/2817, 42 rpm,

2000 mm, W/CP03-19101

XN24AF-RSB096-078 -

FAR-2117/2117-BB/2817, 24 rpm,

2400 mm, W/CP03-19101

XN24AF-RSB097-078 -

FAR-2117/2117-BB/2817, 42 rpm,

2400 mm, W/CP03-19101

XN12AF-RSB096-079 -

FAR-2127/2127-BB/2827, 24 rpm,

1200 mm, W/CP03-24201

XN12AF-RSB097-079 -

FAR-2127/2127-BB/2827, 42 rpm,

1200 mm, W/CP03-24201

XN20AF-RSB096-079 -

FAR-2127/2127-BB/2827, 24 rpm,

2000 mm, W/CP03-19101

XN20AF-RSB097-079 -

FAR-2127/2127-BB/2827, 42 rpm,

2000 mm, W/CP03-19101

XN24AF-RSB096-079 -

FAR-2127/2127-BB/2827, 24 rpm,

2400 mm, W/CP03-19101

Antenna Unit

XN24AF-RSB097-079 -

1

FAR-2127/2127-BB/2827, 42 rpm,

2400 mm, W/CP03-19101

MU-201CR For FAR-2117/2127

Monitor Unit

MU-231CR

- 1

For FAR-2817/2827

Processor Unit RPU-013 - 1

RCU-014 Standard type

Control Unit

RCU-015

- 1

Trackball type

CP03-25601 008-535-550 1 For antenna unit

CP03-25700 000-080-435 15 m signal cable RW-9600

CP03-25710 000-080-436 30 m signal cable RW-9600

CP03-25720 000-080-437 50 m signal cable RW-9600

CP03-25730 000-082-191

1

40 m signal cable RW-9600

CP03-25800 000-080-434 1 Cable assy. for monitor unit

CP03-25602 008-535-940 For RPU-013, AC set

Installation Materials

CP03-25603 008-535-950

1

For RPU-013, DC set

FP03-09810 008-536-010 1 For monitor unit

FP03-09850 008-535-610 For RCU-014

Accessories

FP03-09860 008-535-690

1

For RCU-015/016

iv

Optional Equipment

Name Type Code No. Remarks

Gyro Converter GC-10-2 000-080-440 See chapter 4.

Performance Monitor PM-31 000-080-438 Mandatory for IMO radar

RU-1803 -

Converts 440 VAC to 100 VAC,

for processor unit

Transformer Unit

RU-3305 -

Converts 110/115/220/230 VAC

to 100 VAC, for de-icer

RU-3424 -

115/230 VAC to 24 VDC, for

processor unit (25 kW)

RU-1746B-2 -

115/230 VAC to 24 VDC, for

processor unit (12 kW)

Rectifier

RU-3423 -

100/110/115/220/230 VAC to 24

VDC, for monitor unit

Memory Card Interface Unit CU-200-FAR 000-081-568 W/CP03-27430, See chapter 4.

External Buzzer OP03-21 000-030-097

Control Unit RCU-016 - Remote type, W/FP03-09860

RAM Card 00RAM08MC-005 004-376-740 8 MB

OP03-180-1 008-545-590 Mounted at factory

OP03-180-2 008-536-070 Mounted in field. See chapter 4.

OP03-180-3 008-545-610 Mounted in console at factory.

DVI-RGB Conversion Kit

OP03-180-4 008-545-600 Mounted in console in field.

XH10P-W-6P L=20M 000-149-748 20 m

XH10P-W-6P L=30M 000-149-749 30 m

Between control &

processor unit

XH10P-W-5P-A

L=10M

000-149-050 10 m

XH10P-W-5P-A

L=20M

000-149-051 20 m

XH10P-W-5P-A

L=30M

000-149-052 30 m

Between control

units

DVI-D/D S-LINK 10M

000-150-200

10 m Monitor-Processor

S03-9-5 008-206-640 For external radar, 5 m, 8-8P

S03-9-10 008-206-650 For external radar, 10 m, 8-8P

Cable Assy.

S03-9-15 008-209-160 For external radar, 15 m, 8-8P

SP03-12501 008-485-360 1 For antenna unit

SP03-14404 008-535-910 For processor unit 100 VAC set

SP03-14405 008-535-920 For processor unit 220 VAC set

SP03-14406 008-535-930

1

For processor unit 24 VDC set

SP03-14401 008-535-990 For monitor unit AC set

SP03-03900 000-081-063

For monitor unit, DC set,

MU-201CR

Spare Parts

SP03-14402 008-536-000

1

For monitor unit, DC set,

MU-231CR

v

OP03-28900 000-082-658

FR-FTPC-CY

10 m

OP03-28910 000-082-629

FR-FTPC-CY

20 m

LAN Cable Kit (with armor)

OP03-28920 000-082-660

FR-FTPC-CY

30 m

Modular

connection

MPS588-C,

2 pcs.

FP03-09820 008-535-560 Hanger assy. for MU-201CR

Accessories

FP03-09830 008-536-020 Hanger assy. for MU-231CR

Hand Grip FP03-09840 008-535-570 For monitor unit

03-163-1201 100-307-260 For MU-201CR

Dust Cover

03-163-2101 100-307-270 For MU-231CR

FP03-11500 001-020-090 For MU-201CR

Hood

FP03-11000 008-571-680 For MU-231CR

Clamp Plate OP03-182 008-535-620 For RCU-014

FP03-09870 008-535-630

Flush Mount Kit

OP03-198 001-008-050

For control unit

RCU-016/014/015

OP03-183 008-535-640 For RCU-014&MU-201CR

OP03-184 008-535-650 For RCU-014& MU-231CR

Coupling Pedestal

OP03-185 008-535-660 For RCU-014

BNC Connector Converter DSUB-BNC-1 000-148-528 For VDR

Junction Box RJB-001 -

For more than 100m

antenna cable

Desktop Mount Kit FP03-10201 008-539-530 For CU-200

Console Mount Kit FP03-10202 008-539-540 For CU-200

Switching Hub HUB-100 - See manual of HUB-100.

FP03-11010 001-033-140 For MU-231CR display unit Slim Hood

FP03-11510 001-034-390 For MU-201CR display unit

About the category sticker

This radar meets the requirements in IEC62388 (Marine navigation and

radiocommunication equipment and systems – Shipborne radar – Performance

requirements, method of testing and required test results)

Check the appropriate box on the sticker which is pre-attached on the processor unit,

according to your radar’s specification. Refer to the table shown below to confirm your

category.

Category Radar type ANT. rotation speed

CAT1

FAR-2817, FAR-2827, FAR-2837S,

FAR-2827W, FAR-2837SW

Normal speed

CAT1H FAR-2817, FAR-2827, FAR-2837S HSC

CAT2

FR-2117/BB, FAR-2127/BB,

FAR-2137S/BB

Normal speed

CAT2H

FAR-2117/BB, FAR-2127/BB,

FAR-2137S/BB

HSC

vi

SYSTEM CONFIGURATION

PROCESSOR UNIT

RPU-013

EPFS

(Navigator)

IEC-61162 Serial Data

(Input/Output)

IEC-61162 Serial Data

(Input)

SDME

(Speed Log)

Gyrocompass

AIS

Track Control Unit

: Option

: Dockyard supply

: Standard

Rectifier

RU-3424

RU-1746B-2

AD-100

MEMORY CARD

INTERFACE UNIT

CU- 200-FAR

VDR

External Monitor

Sub Display

Alarm***

MONITOR UNIT

MU-201CR (CAT1)

(FAR-2117/2127)

or

MU-231CR (CAT2)

(FAR-2817/2827)

CONTROL UNIT

RCU-014

(Standard)

or

RCU-015

(Trackball)

Control Unit

RCU-016

(Remote)

Transformer Unit

RU-1803

FAR-2117/2817: XN12AF-RSB-096-078

XN12AF-RSB-097-078

XN20AF-RSB-096-078

XN20AF-RSB-097-078

XN24AF-RSB-096-078

XN24AF-RSB-097-078

FAR-2127/2827: XN12AF-RSB-096-079

XN12AF-RSB-097-079

XN20AF-RSB-096-079

XN20AF-RSB-097-079

XN24AF-RSB-096-079

XN24AF-RSB-097-079

ANTENNA UNIT

Gyro Converter

GC-10

DC spec

AC spec

Performance Monitor

JB

24 VDC

or

100-230 VAC

100/110/115

220/230 VAC

RU-3423

24 VDC

*

Category of Units

Antenna Unit: Exposed to weather

All other units: Protected from weather

Switching HUB

HUB-100

**

1)

2)

3)

1) Connect the EPFS which is approved in accordance with the requirements of the IMO in

resolution MSC.112(73) is used.

2) Connect the SDME which is approved in accordance with the requirements of IMO in

resolution MSC.96(72) is used.

3) Use the gyrocompass having an update rate that is adequate for the ship’s rate of turn.

*: For FAR-2117-BB/2127-BB a monitor unit is prepared by user. See page 1-6.

These monitors have been approved by the IMO, MU-201CR for CAT 2, MU-231CR for

CAT 1. If a different monitor is to be used, its effective diameter must meet the applicable

Category requirements: CAT 1: effective diameter 320 mm or higher, CAT 2: effective

diameter 250 mm or higher. Refer to their operator’s manuals for details.

**: Junction boxes are required for more than 100 m antenna cable.

***: Contact output for Alarm

(Load current) 120 mA (Polarity) No.1, 2: Normally Close, No.3, 4: Normally Open

Serial I/O for alarm is also possible, which complies with IEC 61162-1.

1-1

1. MOUNTING

NOTICE

Do not apply paint, anti-corrosive sealant

or contact spray to coating or plastic

parts of the equipment.

Those items contain organic solvents that

can damage coating and plastic parts,

especially plastic connectors.

1.1 Antenna Unit

Mounting considerations

• The antenna unit is generally installed either on top of the wheelhouse, on the radar mast,

or on a suitable platform. Locate the antenna unit in an elevated position to permit

maximum target visibility.

• A line of sight from the antenna unit to the bow of the ship should hit the surface of the

sea in not more than 500 m or twice the ship’s length, depending which value is smaller,

for all load and trim conditions.

less than 500 m or twice the ship’s length

• Mount the antenna unit so that any blind sectors caused by objects (mast, etc.) are kept

to a minimum. No blind sector should exist in arc of the horizon from right ahead to 22.5°

aft of the beam to either side (see Figure 1 below). Also, individual blind sectors of more

than 5°, or the total arc of both blind sectors of more than 20°, should not occur in the

remaining arc (Figure 2). Note that any two blind sectors separated by 3° or less are

regarded as one sector.

Figure 1

Figure 2

a

a, b, c: less than 5 respectively

a+b+c+... : less than 20

b

c

22.5

less than 3

bow

1. MOUNTING

1-2

• Install the antenna unit away from interfering high-power energy sources and other

transmitting radio antenna.

• Keep the lower edge of the antenna unit above the safety rail by 500 mm or more.

• Two antenna units should be mounted as below:

more than 20

more

than 1 m

• No funnel, mast or derrick should be within the vertical beamwidth of the antenna unit in

the bow direction, especially zero degrees

±5°, to prevent blind sectors and false echoes

on the radar picture.

• It is rarely possible to place the antenna unit where a completely clear view in all

directions is available. Thus, you should determine the angular width and relative bearing

of any shadow sectors for their influence on the radar at the first opportunity after fitting.

• Locate a direction finder antenna clear of the antenna unit to prevent interference to the

direction finder. A separation of more than two meters is recommended.

• A magnetic compass will be affected if the antenna unit is placed too close to the

magnetic compass. Observe the compass safe distances on page ii to prevent deviation

of the magnetic compass.

• Do not paint the radiator aperture, to ensure proper emission of the radar waves.

• The antenna base is made of cast aluminum. To prevent electrolytic corrosion of the

antenna base, use the seal washers and corrosion-proof rubber mat and ground the unit

with the ground wire (supplied).

• Deposits and fumes from a funnel or other exhaust vent can adversely affect the aerial

performance and hot gases may distort the radiator portion. The antenna unit must not be

mounted where the temperature is more than 55°C.

• Leave sufficient space around the unit for maintenance and servicing. See the antenna

unit outline drawing for recommended maintenance space.

1. MOUNTING

1-3

Assembling the antenna unit

The antenna unit consists of the antenna radiator and the antenna unit chassis, and they

are packed separately. Fasten the antenna radiator to the antenna unit chassis as follows:

1. For the XN20AF, XN24AF, attach two guide pins to the underside of the antenna

radiator.

2. Remove the waveguide cap from the radiator bracket. The cap may be discarded.

3. Coat the waveguide flange with anticorrosive sealant as shown below.

Anticorrosive sealant

10 mm

O-ring Waveguide cap

5 mm

Hole for

a guide pin

Hole for

a guide pin

Coating the waveguide flange with anticorrosive sealant

4. Coat fixing holes for the antenna radiator with anticorrosive sealant.

5. Grease the O-ring and set it to the O-ring groove of the radiator flange.

6. Set the antenna radiator to the radiator bracket.

7. Coat hex bolts M8x40 (for XN-20AF or XN-24AF) or hex bolt M8x35/ flat washer/spring

washer (for XN-12AF) with anticorrosive sealant and use them to loosely fasten the

antenna radiator to the antenna unit chassis.

8. Remove two guide pins (inserted at step 1), and then tighten fixing bolts.

CAUTION

Be sure to remove the guide pins.

Injury may result if the guide pins loosen

and fall.

1. MOUNTING

1-4

O-ring

Radiator bracket

Waveguide

Antenna radiator

Hex bolt (M8x40), 8 pcs.

(XN20AF, XN24AF)

Hex. bolt (M8x35), 8 pcs.

Flat washer

Spring washer (XN12AF)

Guide pin

(XN20AF,

XN24AF

only)

Fastening the radiator to the radiator bracket

Fastening the antenna unit to the mounting platform

The antenna unit may be assembled before hoisting it to the mounting platform. However,

do not lift the antenna unit by the radiator. Always hold the unit by its housing. When using a

crane or hoist, lift the unit by the hoist rings which should be fastened to the bolt fixing

covers of the antenna housing.

NOTICE

NO!

- To hoist antenna unit aboard vessel, attach ropes to lifting fixtures and hoist unit with crane.

- To remove load from radiator when hoisting, the length of the rope between the radiator base

and the hook on the should be at least 130 cm.

- To keep the rope away from the radiator, turn the radiator and chassis approx. 30 degrees as

shown below.

- Be sure to remove the lfiting fixtures after hoisting is completed.

130cm

Approx.

30 deg.

Lifting fixture

Crane

(Top view)

NO!

Lifting

fixture

1. Construct a suitable mounting platform referring to the outline drawing at the end of this

manual.

2. Drill four mounting holes of 15 mm diameter and one cable entry hole of about 50 mm

diameter in the mounting platform.

3. Lay the rubber mat (supplied) on the mounting platform.

4. Place the antenna unit on the rubber mat, orienting the unit so the bow mark on its base

1. MOUNTING

1-5

4. Place the antenna unit on the rubber mat, orienting the unit so the bow mark on its base

is facing the ship’s bow.

Ground

terminal

Rubber

mat

Bow mark

Antenna unit, front view

5. Fasten the antenna unit to the mounting platform with M12x60 hex bolts, nuts, flat

washers and seal washers.

6. Using hex bolt (M6x25), nut (M6) and flat washer (M6), establish the ground system on

the mounting platform as shown below. The location should be within 340 mm of the

ground terminal on the antenna unit. Connect the ground wire (RW-4747, 340 mm,

supplied) between the grounding point and ground terminal on the antenna unit. Coat

the entire ground system with silicone sealant (supplied).

Anticorrosive sealant

Seal washer

Rubber mat

Anticorrosive

sealant

Ground wire

Hex bolt

Hex bolt welded to

ship's superstructure

Hex nut

Spring washer

OR

Anticorrosive

sealant

Flat washer

Anticorrosive sealant

Ground

terminal

Ground

wire

Antenna base

Ground wire

How to mount the antenna unit

1. MOUNTING

1-6

1.2 Monitor Unit

The monitor unit can be flush mounted in a console panel, or mounted on a desktop using

the optional accessories.

Note: FAR-2117-BB/2127-BB have no monitor unit. Prepare a suitable monitor locally.

Recommended monitor: SXGA (1280x1024), aspect ratio 5:4

Mounting considerations

When selecting a mounting location, keep in mind the following points:

• Select a location where the display unit can be viewed conveniently and where the

screen can be viewed while facing towards the bow.

• The optimal viewing distances for the radar display units are: MU-170C: 920 mm,

MU-201CR: 1080 mm, MU-231CR: 1200 mm. Select a suitable mounting location

considering the applicable distance.

• Locate the unit out of direct sunlight and away from heat sources because of heat that

can build up inside the cabinet.

• Locate the equipment away from places subject to water splash and rain.

• Leave sufficient space on the sides and rear of the unit to facilitate maintenance.

• A magnetic compass will be affected if the monitor unit is placed too close to the magnetic

compass. Observe the compass safe distances on page ii to prevent deviation of a

magnetic compass.

Mounting procedure

Flush mounting

Follow the procedure below to mount the monitor unit in a console panel.

1. Make cutout in mounting location referring to the outline drawing shown below.

2. Insert the monitor unit to the hole and fix it with four tapping screws (6x30).

3. Attach panel hooks near the fixing holes (upper part). See next page. These are used to

pull out the monitor unit from a console panel for servicing.

4. Attach four panel covers to the fixing holes.

(79)

454

506

534

4-φ8

FIXING HOLES

Monitor unit MU-201CR

490

420

4-FIXING HOLES

30

80

506±1

296±1

(For FAR-2117/2127)

±1

296±1

1. MOUNTING

1-7

570

4-φ8 FIXING HOLES

598

(96)

505

4-FIXING HOLES

554

471

30

80

Monitor unit MU-231CR

570±1

313

±

1

(For FAR-2817/2827)

313

±

1

±

1

Flush mounting of monitor unit

Panel hook

Panel cover

Fixing screw

Attaching panel hook and panel cover

Note: If you need to remove the monitor unit from the mounting panel, remove the four

panel covers with your fingernail and use two panel hooks supplied as accessories to

lift the monitor unit.

1. MOUNTING

1-8

Desktop mounting

Use the optional accessories to mount the monitor unit on a desktop.

• For FAR-2117/2127: FP03-09820 (Code No.: 008-535-560)

• For FAR-2817/2827: FP03-09830 (Code No.: 008-536-020)

Contents of FP03-09820/09830

Name Type Code No. Qty Remarks

Hanger L 03-163-1111 100-305-141 1

Hanger R 03-163-1112 100-305-181 1

03-163-1113 100-305-191 For FAR-2117/2127

Hanger stay

03-163-2071 100-305-371

1

For FAR-2817/2827

Hole plug CP-30-HP-13 000-160-074-10 2

Plastic rivet KB-13 Rivet Black 000-570-276-10 4

Hex. bolt M6x25 000-162-949-10 4

Hex. bolt M10x30 000-162-884-10 2

Spring washer M10 000-864-261 2

Flat washer M10 000-864-131 2

1. Assemble two hangers and hanger stay with two hex bolts (M10x30), flat washers and

spring washers and cover each hex bolt with hole plug.

2. Fix the above assembly to the mounting location with four hex bolts (M12, dockyard

supply).

3. Fasten the monitor unit to the mounting hanger assembly with four hex bolt (M6x25,

supplied).

4. Cover each hex bolts with panel cover.

5. Cover each holes for hand grip on the hangers with plastic rivets (4 pcs).

1. MOUNTING

1-9

Panel cover

Hex bolt

(M6x25)

Hanger (R)

Hanger stay

M12 bolts for fixing

(Dockyard supply)

Hanger (L)

Hex bolt

M10x30

Plastic rivet

Hole plug

Panel cover

To remove this, insert fingernail in groove.

Flat Washer M10

Spring Washer M10

Monitor Unit

 The hand grip is optionally available for the desktop mounting monitor unit.

Handle

Screw

Wave washer

Rosette washer

Hood (option)

When it is too bright in the daytime, use the optional hood to shade the screen.

• For FAR-2117/2127: FP03-11500 (Code No.: 001-020-090)

• For FAR-2817/2827: FP03-11000 (Code No.: 008-571-680)

Contents of hood

Name Type Code No. Qty. Remarks

Hood (21) FP03-11501 001-020-120 1 For FAR-2117/2127

Hood (23) FP03-11001 008-571-700 1 For FAR-2817/2827

Fixing plate 03-163-2202-0 100-335-560-10 4

Screw M4x10 D=13 US304 000-862-543 4

1. MOUNTING

1-10

1. Desktop mounting: Fasten the fixing plates to the fixing holes with the hex head bolts

(supplied).

Flush mounting: Fasten the display unit to the mounting location, and then attach the

fixing plates with four self-tapping screws.

Fixing plate

Fixing hole

Hex head bolt

2. Attach the hood to the display unit (the hood is outside of the fixing plates).

3. Fasten the hood to the fixing plates with four screws supplied (M4x10).

1.3 Control Unit

The control unit may be mounted on a desktop, with or without the KB fixing metal

(supplied), which mounts the control unit at an angle.

Mounting considerations

When selecting a mounting location, keep in mind the following points:

• Select a location where the control unit can be operated conveniently.

• Locate the unit away from heat sources because of heat that can build up inside the

cabinet.

• Locate the equipment away from places subject to water splash and rain.

• Determine the mounting location considering the length of the signal cable between the

control unit and the processor unit. (The 10m signal cable is attached to the control unit).

• A magnetic compass will be affected if the control unit is placed too close to the magnetic

compass. Observe the compass safe distances on page ii to prevent deviation of a

magnetic compass.

1. MOUNTING

1-11

Fixing with KB fixing plate

1. Fix the KB fixing plate to the bottom of the control unit.

2. Attach cushions (three for RCU-014, two for RCU-015/016) to the bottom of the control

unit as shown below.

3. Fix it to a desired location with self-tapping screws (local supply).

Cushion

KB fixing plate

Side view for RCU-014/015/016

Fixing without KB fixing metal

1. Drill four mounting holes of 5 mm diameter referring to the outline drawing at the back of

this manual.

2. Fix the control unit with four screws (M4) from under side of the desktop. (The M4

screws with a sufficient length for the thickness of the desktop should be provided

locally.)

#70

308±1

398

136±1

180

4-M4 (Fixing holes)

(bottom)

Control Unit RCU-014

F4

F3

F2

F1

180

24 32

110±1

160

136±1

4-M4 (Fixing holes)

(REAR)

RCU-015/016

1. MOUNTING

1-12

Flush mounting

Use the optional flush mount kit FP03-09870 to mount the control unit RCU-014, RCU-015

and/or RCU016 to a console panel.

Name: Flush mount kit

Type: FP03-09870

Code No.: 008-535-630

No. Name Type Code No. Qty

1 Mount plate 03-163-7531 100-306-261 4

2 Hex nut M5 000-863-108 4

3 Wing screw M5x40 000-162-682-10 4

4 Pan head screw M4x12 000-163-192-10 4

1. Prepare a cutout in the mounting location as shown in the figure below.

388 150±2

170±2 176±2

±2

For RCU-014 For RCU-015 and RCU-016

2. Set the control unit to the cutout.

3. Attach the mounting plate to the control unit with four screws from the rear side.

4. Screw the wing screw to each mounting plate and then insert hex bolt to each wing

screw.

5. Fasten each wing screw and then fasten the hex nuts as shown in the figure below.

(P)

#70

53

92

(P)

#70

171

53

86

Note: P 10

<

=

RCU-014 RCU-015/RCU-016

Page is loading ...

Furuno FAR-2117-BB User manual

This manual is also suitable for

Furuno FAR-2117-BB User manual

Related papers

Other documents