Furuno FAR-2167DS User manual

All brand and product names are trademarks, registered trademarks or service marks of their respective holders.

www.furuno.co.jp

MARINE RADAR

FAR-2167DS/2167DS-BB

Installation manual

SAFETY INSTRUCTIONS....................... i

SYSTEM CONFIGURATION ................. iii

EQUIPMENT LISTS .............................. iv

1. MOUNTING ..................................... 1-1

1.1 Antenna Unit ........................................ 1-1

1.2 Monitor Unit ........................................ 1-7

1.3 Control Unit ........................................ 1-10

1.4 Processor Unit .................................. 1-15

1.5 Power Supply Unit ............................ 1-16

2. WIRING ........................................... 2-1

2.1 Wiring Overview................................... 2-1

2.2 Antenna Unit ........................................ 2-2

2.3 Monitor Unit (for FAR-2167DS)............ 2-7

2.4 Processor Unit ..................................... 2-8

2.5 Power Supply Unit ............................. 2-13

2.6 Changing AC Power Specification ..... 2-15

3. ADJUSTMENTS..............................3-1

3.1 Initializing tuning .................................. 3-1

3.2 Heading Alignment............................... 3-2

3.3 Adjustment Sweep Timing.................... 3-5

3.4 Suppressing Main Bang ....................... 3-6

3.5 Other Settings ...................................... 3-7

4. OPTIONAL EQUIPMENT ................4-1

4.1 Gyro Converter GC-10 ......................... 4-1

4.2 Memory Card Interface Unit ............... 4-10

4.3 DVI-RGB Conversion Kit.................... 4-13

4.4 BNC Connector Converter ................. 4-16

5. IO DATA...........................................5-1

PACKING LISTS ................................ A-1

OUTLINE DRAWINGS ....................... D-1

INTERCONNECTION DIAGRAM ....... S-1

The paper used in this manual

is elemental chlorine free.

・FURUNO Authorized Distributor/Dealer

9-52 Ashihara-cho,

Nishinomiya, 662-8580, JAPAN

Telephone : +81-(0)798-65-2111

Fax

:

+81-(0)798-65-4200

A : FEB 2007

.

Printed in Japan

F : APR . 11, 2011

Pub. No. IME-35230-F

*00014869015**00014869015*

(HIMA ) FAR-2167DS/2167DS-BB

*

00014869015

*

00014869015

*

* 0 0 0 1 4 8 6 9 0 1 5 *

i

WARNING

Indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation which, if not avoided,

may result in minor or moderate injury.

Warning, Caution

Mandatory Action

Prohibitive Action

SAFETY INSTRUCTIONS

T

he installer must read and follow all the safety instructions before attempting to install the

e

quipment.

WARNING

The radar antenna emits electromagnetic radio frequency (RF) energy which can

be harmful, particularly to your eyes. Never look directly into the antenna aperture

from a close distance while the radar is in operation or expose yourself to the

transmitting antenna at a close distance.

Distances at which RF radiation levels of 100 W/m

2

and 10 W/m

2

exist are given in

the table below.

Note: If the antenna unit is installed at a close distance in front of the wheel house

,

it may be necessary to halt transmission within a certain sector of antenna

revolution. This can be done from the SCANNER menu.

Radio Frequency Radiation Hazard

Distance to

100 W/m

2

point

Distance to

10 W/m

2

point

Radiator type

SN30AF

SN36AF

0.60 m

0.40 m

8.90 m

7.40 m

ii

WARNING

Do not open the equipment unless

totally familiar with electrical circuits

and service manual.

Only qualified personnel should work

inside the equipment.

Wear a hard hat and safety belt when

mounting the antenna unit.

Serious injury or death can result if

someone falls from the radar antenna mast.

Construct a suitable service platform

from which to install the antenna unit.

Serious injury or death can result if

someone falls from the radar antenna

mast.

Do not install units other than the

antenna unit in a place subject to rain

or water splash.

Fire, electrical shock or injury can result if

water leaks into those units.

Turn off the power at the switchboard

before beginning the installation.

Fire, electrical shock or injury can result if

the power is on during the installation.

Use only the specified power cables.

Use of power cables that are thinner than

those specified can cause fire.

Securely attach protective earth to the

ship's body.

The protective earth is required to prevent

electrical shock.

A proper license is necessary to install

a radar.

See your dealer for details.

Observe the following compass safe

distances to prevent interference to a

magnetic compass:

CAUTION

Antenna Unit

(60 kw)

Standard

compass

Monitor Unit

(MU-201CR)

1.55 m 1.00 m

Processor Unit

(RPU-013)

1.35 m 0.85 m

Control Unit

(RCU-014)

0.30 m 0.30 m

Control Unit

(RCU-015)

0.95 m 0.60 m

Control Unit

(RCU-016)

0.65 m 0.45 m

Power Supply

Unit (PSU-006)

Memory Card

Interface Unit

(CU-200)

0.90 m 0.60 m

Steering

compass

4.30 m 2.80 m

0.30 m 0.30 m

Switching Hub

(HUB-100)

1.00 m 0.60 m

Monitor Unit

(MU-190

)

1.65 m

1.05 m

iii

SYSTEM CONFIGURATION

PROCESSOR

UNIT

RPU-013

Navigator

IEC-61162 Serial data

(I/O)

IEC-61162 Serial data

(Input)

Speed Log

Gyrocompass

AIS

Track Controller

: Optional supply

: Local supply

: Standard supply

100-115 VAC/

220-230 VAC

1φ, 50/60 Hz

AD-100

MEMORY CARD

INTERFACE UNIT

CU-200-FAR

VDR

External

Monitor

Radar Remote

Display

Alarm

MONITOR UNIT

MU-201CR

or

MU-190

CONTROL UNIT

RCU-014

(Standard)

OR

RCU-015

(Trackball)

CONTROL UNIT

RCU-016

TRANSFORMER

RU-1803

440 VAC

1φ, 50/60 Hz

GYRO CONVERTER

GC-10

100-230 VAC

1φ, 50/60 Hz

SWITCHING HUB

HUB-100

Equipment category

Unit

Antenna

Other units

Category

Exposed to weather

Protected from weather

100-115V/220-230 VAC

1φ, 50/60 Hz

TRANSFORMER

RU-1803

440 VAC, 1φ,

50/60 Hz

110 VAC, 3φ, 60 Hz

220 VAC, 3φ, 50 Hz

440 VAC, 3φ, 50 Hz

(For high voltage)

TRANSFORMER

RU-5693

TRANSFORMER

RU-6522

TRANSFORMER

RU-5466-1

*

* FAR-2167DS-BB is not equipped with

a monitor unit. Procure one locally.

ANTENNA UNIT

RADIATOR

SN30AF

SN36AF

CHASSIS

RSB-111/112

POWER SUPPLY UNIT

PSU-006

200 VAC, 3φ, 50 Hz

220 VAC, 3φ, 60 Hz

(For amtenna motor)

380 VAC, 3φ, 50 Hz

440 VAC, 3φ, 60 Hz

iv

EQUIPMENT LISTS

Standard supply

* See packing list at end of this manual.

Name Type Code No. Qty Remarks

Antenna Unit SN30AF –

1

Radiator

SN36AF –

RSB-111 –

1

200 VAC, 3φ, 50 Hz

220 VAC, 3φ, 60 Hz

Chassis

RSB-112 – 380 VAC, 3φ, 50 Hz

440 VAC, 3φ 60 Hz

Power Supply

Unit

PSU-006 – 1

Monitor Unit MU-201CR – 1

MU-190 –

Processor Unit RPU-013 – 1

Control Unit RCU-014 –

1

Standard-type

RCU-015 – Trackball-type

Installation

Materials*

CP03-31501 008-573-780 1 For antenna unit

CP03-25700 000-080-435

1

15 m signal cable (RW-9600)

CP03-25710 000-080-436 30 m signal cable (RW-9600)

CP03-25730 000-082-191 40 m signal cable (RW-9600)

CP03-25720 000-080-437 50 m signal cable (RW-9600)

CP03-25800 000-080-434 1 Cable assy. for monitor unit

CP03-25602 008-535-940 1 For processor unit

CP03-31401 008-572-750 1 For power supply unit

CP03-25604 008-539-850 1 For control unit

Accessories* FP03-09810 008-536-010 1 For monitor unit.

FP03-09850 008-535-610

1

For standard-type control unit

FP03-09860 008-535-690 For trackball-type control unit

FP03-10101 008-538-730 1 For antenna unit

Spare Parts* SP03-14404 008-535-910

1

For processor unit, 100 VAC

SP03-14405 008-535-920 For processor unit, 220 VAC

SP03-14401 008-535-990 1 For monitor unit

SP03-15501 008-572-730

1

For power supply unit, 100 VAC

SP03-15502 008-572-740 For power supply unit, 220 VAC

v

Optional equipment

Name Type Code No. Remarks

Gyro Converter GC-10-2 000-080-440 See Chapter 4.

Stepdown

Transformer

Unit

RU-1803

–

440 to 100 VAC, for processor unit

RU-5693

–

110 to 220 VAC, 3φ, for antenna unit

RU-6522

–

220 to 200 VAC, 3φ, for antenna unit

RU-5466-1 – 440 to 200 VAC, 3φ, for antenna unit

Memory Card

Interface Unit

CU-200-FAR 000-081-568 w/CP03-27430, see Chapter 4.

External Alarm

Buzzer

OP03-21 000-030-097

Control Unit RCU-016 000-080-299 Remote type, w/FP03-09860

RAM Card O0RAM08MC-005 004-376-740 8MB

DVI-RGB

Converter Kit

OP03-180-1 008-545-590 For installation in field.

OP03-180-2 008-536-070 For installation in field. See Ch. 4.

Cable Assy. XH10P-W-6P L=20M 000-149-748

Processor unit

QControl unit, 20 m

XH10P-W-6P L=30M 000-149-749

Processor unit

QControl unit, 30 m

XH10P-W-5P-A L=10M 000-149-050 Between control units, 10 m

XH10P-W-5P-A L=20M 000-149-051 Between control units, 20 m

XH10P-W-5P-A L=30M 000-149-052 Between control units, 30 m

DVI-D/D S-LINK 10M 000-150-200

Processor unit

QControl unit, 10 m

S03-9-5(8-8P) 008-206-640 External radar, 5 m, 8-8P

S03-9-10(8-8P) 008-206-650 External radar, 10 m, 8-8P

S03-9-15(8-8P) 008-209-160 External radar, 15 m, 8-8P

Installation

Materials

(Armored LAN-

Cable Kit)

CP03-28900 000-082-658 FR-FTPC-CY 10 m, modular

connector MPS588-C, 2 pcs.

CP03-28910 000-082-659 FR-FTPC-CY 20 m, modular

connector MPS588-C, 2 pcs.

CP03-28920 000-082-660 FR-FTPC-CY 30 m, modular

connector MPS588-C, 2 pcs.

Bracket Assy. FP03-09820 008-535-560 Hanger assy. for monitor unit

Handgrip Assy. FP03-09840 008-535-570 For monitor unit

Dust Cover 03-163-1201 100-307-260 For monitor unit

Clamp Assy. OP03-182 008-535-620 For RCU-014

Flush Mount Kit FP03-09870 008-535-630 For control unit

OP03-198 001-008-050

Connection

Stand

OP03-183 008-535-640

RCU-014

QMU-201CR

OP03-185 008-535-660 RCU-014

Hanger Kit FP03-10201 008-539-530 Desktop inst. kit for CU-200-FAR

BNC

Connector

Converter

DSUB-BNC-1 000-148-528 For connecting VDR

Switching Hub HUB-100 – See Operator's Manual for HUB-100,

issued separately.

Hood FP03-11500 001-020-090 For MU-201CR display unit

Slim Hood FP03-11510 001-034-390 For MU-201CR display unit

vi

This page is intentionally left blank.

1-1

1. MOUNTING

1.1 Antenna Unit

Mounting considerations

The antenna unit is generally installed either on top of the wheelhouse, on the radar mast, or on

a suitable platform. The mounting location should afford a good all-round view and satisfy the

siting and mounting considerations mentioned below.

Siting

• No funnel, mast or derrick should be within the vertical beamwidth of the antenna unit in the bow

direction, especially zero degrees ±5°, to prevent blind sectors and false echoes on the radar

picture.

• Deposits and fumes from a funnel or other exhaust vent can adversely affect the aerial perfor-

mance and hot gases may deform the radiator. The antenna unit must not be mounted where

the temperature is more than 70°C.

• Locate a direction finder antenna clear of the antenna unit to prevent interference to the direc-

tion finder. A separation of more than two meters is recommended.

• Choose a location where reflections from the radar reflector will not be received by the radar

antenna.

• The "standard" antenna unit orientation has the cable glands directed toward the bow.

• Leave sufficient space around the unit for maintenance and servicing. See the antenna unit out-

line drawing for recommended maintenance space.

Mounting

• Use rope and crane to hoist the antenna unit to the mounting location. Lifting fixtures are pro-

vided on the antenna chassis to which to fasten rope.

• Mount the unit parallel to the waterline.

• A hole is required in the mounting platform for the antenna cable.

• An appropriate platform should be constructed at the mounting location to facilitate installation

and maintenance work.

• Connect ground wire between antenna terminal on antenna chassis and ground point.

• If the mounting platform is made of steel paint it to prevent electrolytic corrosion. DO NOT paint

the antenna radiator.

NOTICE

Do not apply paint, anti-corrosive sealant

or contact spray to coating or plastic

parts of the equipment.

Those items contain organic solvents that

can damage coating and plastic parts,

especially plastic connectors.

1-2

Installation precaution for S-band antenna unit

If an S-band antenna unit is mounted near the end of a platform to provide sufficient rotation clear-

ance for the radiator, the antenna unit, because of its weight, will swing up and down by ship's

vibration and rolling. This exerts excessive levels of stress at the base of the radiator, which can

damage the radiator. To prevent this, relocate the antenna unit, or if relocation is not possible rein-

force the platform.

Mounting precaution for S-band antenna unit

Mast for

DF, etc.

Mount antenna unit

directly on mast or on

a platform, as near as

possible to center of mast.

Mast for DF

Remarkable vibration

(pitching)

Mounting

position

EXAMPLE

1-3

Assembling the antenna unit

The antenna unit should be assembled before mounting it. Follow the procedure below to

assemble the antenna unit.

1. Screw the guide pins (2 pcs.) in the radiator.

2. Remove the protective cap from the choke guide and radiator.

3. Grease the O-ring and set it to the groove on the choke guide.

4. Place the radiator on the radiator bracket. (Radiator direction is shown by the logo on the

bracket. If reversely oriented the radiator cannot be set to the bracket.)

5. Loosely fix the radiator to the radiator bracket with hex bolts (M10×25), spring washers and flat

washers.

6. Remove the guide pins and tighten the hex bolts.

Assembling the antenna unit

Radiator front

Guide pin (2 pcs.)

Arrow mark for the radiator front.

Antenna radiator

Do not remove teflon tube

from the center conductor.

O-ring

Choke guide

Radiator bracket

Protective cap

Spring washer,

flat washer,

10 pcs. each,

M10x25

CAUTION

Be sure to remove the guide pins

after fixing the radiator.

Injury may result if the guide pins loosen

and fall from antenna radar platform.

NOTICE

1-4

How to hoist the antenna unit

1. Fix the antenna radiator to the antenna unit chassis as shown on page 1-3.

2. Attach the lifting fixtures and collars as shown below.

3. Position the radiator as shown below and arrange the ropes A and B.

Attachment of lifting fixtures, collar and ropes

Spring washer

Supplied as accessories.

Remove after installation.

*

Spring washer

Lifting fixture

Collar

Flat washer (M12)

Hex bolt (M12x20)

(Torque: 63.5 Nm)

Remove lifting fixture, coat threads

of hex bolts with silicone grease, and

then insert bolts in antenna chassis.

Lifting hook (2 pcs.)

B 1.8m

A 2m

* 2. Place protective material

(cardboard, foam, etc.) between

rope and radiator at the

asterisk-marked locations, to

prevent damage to radiator.

1-5

Fastening the antenna unit to the mounting platform

Note: The antenna is made of cast aluminum, which is subject to electrolytic corrosion if the

mounting platform is steel or iron. To prevent electrolytic corrosion, use the supplied seal washers

and corrosion-proof rubber mat.

Fix the antenna unit to the mounting location, referring to the procedure below and the illustration

on the next page.

1. Referring to the antenna outline drawing, prepare a mounting platform. Drill eight fixing holes

of 15 mm in diameter in the mounting platform or the deck.

• The diameter of the mast for the mounting platform must be over 250 mm.

• The thickness of the platform must be over 15 mm.

• The reinforcement rib must be installed diagonally as shown below.

Installation of reinforcement ribs

WARNING

Do not open the equipment unless

totally familiar with electrical circuits

and service manual.

Only qualified personnel should

work inside the equipment.

Wear a hard hat and safety belt when

mounting the antenna unit.

Serious injury or death can result if

someone falls from the radar antenna mas

t.

Construct a suitable service platform

from which to install the antenna unit.

Serious injury or death can result if

someone falls from the radar antenna

mast.

Over 15 mm

At least 250 mm in diameter,

Thickness at least 6 mm.

Use two nuts.

Ship's bow

Install the reinforcement

rib diagonally.

Bottom view

1-6

2. Lay the corrosion-proof rubber mat (supplied) on the mounting platform, aligning the holes on

the rubber mat with the fixing holes on the mounting platform.

3. Lay the antenna unit on the rubber mat, orienting it so the cable gland is directed toward ship's

bow. Remove the lifting fixtures and collars.

4. Fix the antenna base to the mounting platform with four M12×70 hex bolts, nuts, washers and

seal washers (supplied).

5. Arrange the ground point at a location on the mounting platform that is within 300 mm from the

ground terminal on the antenna unit. Fasten the ground wire (RW-4747, 340 mm) there, using

the M6×25 hex bolt, nut and washers.

6. Connect the other end of the ground wire to the ground terminal on the antenna unit.

7. Coat the ground terminal, ground point on the mounting platform and fixing bolts on the

antenna unit with anticorrosive sealant (supplied).

Mounting the antenna unit

Seal

washer

Corrosion-

proof

rubber

mat

Use two nuts.

(Torque: 63.5 Nm)

Fasten ground wire and then

coat with anitcorrosive sealant.

Ground wire

Antenna chassis

Hex bolt

OR

Ground wire

Coat with

anticorrosive

sealant.

Ground wire

Welding

Hex nut

Ground terminal provided on antenna base.

Lay corrosion-proof rubber mat,

bolt antenna unit to mounting

location, and coat exposed

hardware with anticorrosive sealant.

Arrange ground terminal as close

as possible to antenna unit.

Hex bolt

Flat washer

Hex nut

Spring washer

Flat washer

G1_1/4-A

Ground terminal

Spring washer

1-7

1.2 Monitor Unit

The monitor unit is can flush mounted in a panel or mounted on a desktop (requires optional

accessories).

The FAR-2167DS-BB is not equipped with a monitor unit. Procure a suitable monitor unit locally.

Recommended monitor: SXGA (1280×1024), aspect ratio 5:4.

For MU-190, see the applicable Operator’s Manual.

Mounting considerations

When selecting a mounting location, keep in mind the following points:

• Select a location where the screen can be viewed conveniently while facing the bow.

• Locate the unit out of direct sunlight and away from heat sources because of heat that can build

up inside the cabinet.

• Locate the unit away from places subject to water splash and rain.

• Leave sufficient space on the sides and rear of the unit to facilitate maintenance, referring to the

outline drawing for maintenance space.

• The monitor unit will give interference to a magnetic compass if it is placed too close to the com-

pass. Observe the compass safe distances on page ii to prevent interference to the compass.

Mounting procedure

Flush mounting

Follow the procedure below to mount the monitor unit in a console.

1. Make a cutout in the mounting location referring to the outline drawing shown below.

2. Set the monitor unit to the hole and fix it with four self-tapping screws (6×30).

3. Attach panel hooks near the fixing holes (upper part). See next page. These are used to pull

out the monitor unit from the panel for servicing.

4. Attach four panel covers to the fixing holes.

Mounting dimensions for flush mounting the monitor unit

(79)

454

506

534

4-φ8

FIXING HOLES

490

420

4-FIXING HOLES

30

80

506 1

296

1

296

1

1-8

How to attach panel hook and panel cover

Note: If you need to remove the monitor unit from the console, remove the four panel covers with

your fingernail and use two panel hooks supplied as accessories to lift the monitor unit.

Desktop mounting

Use the optional desktop mouting kit (Type: FP03-09820, Code No.: 008-535-560) to mount the

monitor unit on a desktop.

1. Assemble two hangers and hanger stay with two hex bolts (M10×30), flat washers and spring

washers and cover each hex bolt with hole plug.

2. Fix the above assembly to the mounting location with four hex bolts (M12, dockyard supply).

3. Fasten the monitor unit to the mounting hanger assembly with four hex bolts (M6×25, supplied).

4. Cover each hex bolt with a panel cover (4 pcs.).

5. Cover fixing holes for hand grips with snap buttons (4 pcs).

Contents of desktop mounting kit FP03-0982

0

Name Type Code No. Qty

Hanger L 03-163-1111 100-305-141 1

Hanger R 03-163-1112 100-305-181 1

Hanger stay 03-163-1113 100-305-191 1

Hole plug CP-30-HP-13 000-160-074-10 2

Snap button KB-13, Black 000-570-276-10 4

Hex. bolt

M6

×25

000-162-884-10 4

Hex. bolt

M10

×30

000-162-884-10 2

Spring washer M10 000-864-261 2

Flat washer M10 000-864-131 2

Panel hook

Panel cov

er

Fixing screw

1-9

Fastening monitor unit to hanger

Attaching hand grips

Hand grips are optionally available for the desktop-mount monitor unit. Attach them as follows:

1. Remove the snap buttons attached at step 5 on the previous page.

2. Fix hand grips with wave washers, rosette washers and flat head screws.

How to attach hand grips

Attaching hood

When it is too bright in the daytime, use the optional hood (Type: FP03-11500, Code No.: 001-

020-090) to shade the screen.

Contents of hood

Name Type Code No. Qty.

Hood FP03-11501 001-020-120 1

Fixing plate 03-163-2202-0 100-335-560-10 4

Screw M4x10 D=13 US304 000-862-543 4

Panel cover

Hex bolt

(M6x25)

Hanger (R)

Hanger stay

M12 bolts for fixing

(Dockyard supply)

Hanger (L)

Hex bolt

M10x30

Snap button

Hole plug

Panel cover

To remove this, insert fingernail in groove.

Flat Washer M10

Spring Washer M10

Hand grip

Flat head screw (torque: 7.6 Nm)

Wave washer

Rosette washer

1-10

1. Desktop mounting: Fasten the fixing plates to the fixing holes with the hex head bolts (sup-

plied).

Flush mounting: Fasten the display unit to the mounting location, and then attach the fixing

plates with four self-tapping screws.

2. Attach the hood to the display unit (the hood is outside of the fixing plates).

3. Fasten the hood to the fixing plates with four screws supplied (M4x10).

1.3 Control Unit

Mounting considerations

The control unit may be mounted on a desktop, with or without the KB fixing metal (supplied) which

mounts the control unit at an angle. When selecting a mounting location, keep in mind the fol-

lowing points:

• Select a location where the control unit can be operated conveniently while observing the dis-

play screen.

• Locate the unit away from heat sources because of heat that can build up inside the cabinet.

• Locate the equipment away from places subject to water splash and rain.

• Determine the mounting location considering the length of the signal cable between the control

unit and the processor unit. (A 10 m signal cable is attached to the control unit.)

• A magnetic compass will be affected if the control unit is placed too close to it. Observe the com-

pass safe distances on page ii to prevent interference to a magnetic compass.

Mounting procedure

Fixing with KB (keyboard) fixing plate

The KB fixing plate sits the control unit at a comfortable angle, like the retractable legs on a PC

keyboard.

1. Fix the KB fixing plate to the bottom of the control unit.

2. Attach cushions (three for RCU-014, two for RCU-015/RCU-016) to the bottom of the control

unit as shown below.

3. Fix the unit to a desired location with self-tapping screws (local supply).

Control unit RCU-014/015/016, side view

Fixing plate

Fixing hole

Hex head bolt

Cushio

n

KB fixing plate

1-11

Fixing without KB fixing plate

1. Drill four mounting holes of 5 mm diameter, referring to the outline drawing at the back of this

manual.

2. Fix the control unit with four screws (M4) from the under side of the desktop. (M4 screws with

a sufficient length for the thickness of the desktop should be provided locally.)

Mounting dimensions for control unit RCU-014

Mounting dimensions for control unit RCU-015/RCU-016

#70

308±1

398

136±1

180

4-M4 (Fixing holes

)

(bottom)

# Minimum recommended service space

F4

F3

F2

F1

180

24 32

110±1

160

136±1

4-M4 (Fixing holes)

(REAR)

1-12

Flush mounting

Use the optional flush mount kit FP03-09870 (Code No. 008-535-630) to flush mount the control

unit RCU-014, RCU-015 and/or RCU016 in a console.

1. Prepare a cutout in the mounting location as shown in the figure below.

Flush mount cutout for RCU-014 Flush mount cutout for RCU-015 and RCU-016

2. Set the control unit to the cutout.

3. From the rear side, attach the mounting plate to the control unit with four screws.

4. Screw the wing screw to each mounting plate and then insert hex bolt to each wing screw.

5. Fasten each wing screw and then fasten the hex nuts as shown in the figure below.

Flush mount mounting dimensions for control unit RCU-014 (left) and RCU-015/RCU-016

Contents of flush mount kit for RCU-014/015/016

Name Type Qty

Mounting plate 03-163-7531 4

Hex bolt M5 4

Wing screw

M5

×40

4

Pan head screw

M4

×12

4

388 150±2

170±2 176±2

±2

(P)

#70

53

92

(P)

#70

171

53

86

Note: P 10

<

=

# Minimum recommended service space

To change location of

cable entrance, see

page 1-14.

Page is loading ...

Furuno FAR-2167DS User manual

This manual is also suitable for

Furuno FAR-2167DS User manual

Related papers

Other documents