HUANUO HNCM12 Installation guide
- Category
- Flat panel desk mounts
- Type
- Installation guide
Model: HNCM12
V7.0 (A)
Monitor Desk Mount Instruction Manual
Thank you for choosing this HUANUO product! At HUANUO we strive to provide
you with the best quality products and services in the industry. Should you have
any issues, please don't hesitate to contact us at
Technical Support:
(US/CA)1-800-556-0533 Mon-Fri 8am - 8pm(CST)
(UK)44-808-196-3874 Mon-Fri 2pm - 10pm(UTC）
Other Info:
Website: www.huanuoav.com
01
Tools Needed (Not Included)
Phillips Screwdriver
Please carefully read all instructions before attempting installation. If you do not
understand the instructions or have any concerns or questions, please contact
our customer service at [email protected].
CAUTION: Avoid potential personal injuries and property damage!
• Do not use this product for any purpose that is not explicitly specified in this
manual. Do not exceed weight capacity. We are not liable for damage or injury
caused by improper mounting, incorrect assembly or inappropriate use.
• The desk must be capable of supporting five times the weight of the monitor
and mount combined.
Check the VESA Pattern of Your Monitor before the Installation
IMPORTANT SAFETY INFORMATION
If your monitor VESA is greater than 100x100 mm/4x4 in or less than
VESA 75x75 mm/3x3 in, this mount is NOT compatible.
If this mount is NOT compatible, please contact customer service at
[email protected] to find a compatible mount.
MAX: 100mm/4 in
MAX: 100mm/4 in
Minimum VESA pattern:
75mm/3 in (W)x75mm/3 in (H)
100 mm ≈ 4 in
75 mm ≈ 3 in
3/8 in (10mm)
Socket Wrench
Electric Drill(Optional)
7/16 in (11mm) -
55/64 in (22mm)
Electric Drill(Optional)
Note：
For the thin PB desks or glass table tops, you will
need our Monitor Mount Reinforcement Plate
HNDA1(ASIN: B08CK24TCX ), which provides a
better way to install your monitor mount on a
desktop through C clamp installation.
If your monitor does not have any mounting hole,
you will need our Universal VESA Bracket Kit
HNMUA4(ASIN: B088CWY5Q3)(Fits most
monitors within the size of 32 in)
02
Washer
M10
C1 (x1)
Nut
M10
C2 (x1)
Bolt
M6X12mm
C3(x1)
Bolt
M6X8mm
E (x2)
13/64 in (5mm)
Large Allen Key
F1
(x1)
5/32 in (4mm）
Small Allen Key
F2
(x1)
Locking Plate
a (x1)
C-Clamp Brace
02 (x1)
C-Clamp
03 (x1)
Pole
01 (x1)
Bottom Pad
b (x1)
Supplied Parts and Hardware for Step 1
Supplied Parts and Hardware
Warning: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not use
damaged or defective parts. lf you require replacement parts, please contact our
customer service at [email protected].
• Please note: Not all hardware included in this package will be used.
Supplied Parts for Step 2
Decorative Cover
c (x1)
Monitor Connector
04 (x1)
M8X10mm
D1 (x2)
Washer
M6
D2 (x1)
03
Step 1
F (x1)
Bolt
M6X16mm
Supplied Parts and Hardware for Step 3
Supplied Hardware for Step 4
Faceplate
05 (x1)
Install the Base
Bolt
M4x12mm
A1 (x4)
Bolt
M4x30mm
A2 (x4)
L13mm Spacer
B1 (x4) M4 Washer
B2 (x4)
Option A：
C-Clamp Installation
02
01
Small
Allen Key
F2
E
C3
Small
Allen Key
F2
b
03
02
D2
a
03
04
Large
Allen Key
D1
F1
DeskDesk DeskDesk
Tighten
Desk
Thickness
2 11/64 in (55mm) - 3 5/32 in (80mm)
Desk
Thickness
1 3/16 in (30mm) - 2 11/64 in (55mm)
Desk
Thickness
3/8 in (10mm) - 1 3/16 in (30mm)
Option B:
Grommet Installation
03a 03b
03b
05
Step 2
c
Secure the Monitor Connector and Decorative Cover to
Pole Assembly
04
F1
Large Allen Key
Tighten
04
DeskDesk Desk
Desk
Height
Adjustment
b
1. If the existing grommet hole comes with a
plastic protector, remove it to ensure a flat
surface before installing the desk mount.
2. If there is no grommet hole on your desk,
mark the pilot hole on your your desired
position. Drill a hole using the drill bit in a
diameter of 7/16 in (11mm) - 55/64 in
(22mm) at the marked position through the
mounting surface.
01
b
a
03b
C1
C2
25/32 in - 3 5/32 in
(20-80mm)
7/16 in - 55/64 in
(11-22mm)
06
Attach the Faceplate to the Back of MonitorStep 3
Step 4 Hang the Monitor to the Stand
F
F2
Small Allen Key
Phillips
Screwdriver
(Not Included)
Or
75x75mm
100x100mm
A1 B1/B2
75x75mm
100x100mm
A2
UP
HEAVY! You may need
assistance with this step.
WARNING
Case：If the head
is not straight.
Solution
07
1. If the monitors can stay at the
desired height by itself, no
adjustment needed.
2. The tilt angle of the monitor will
not be adjusted if the set screw [T]
is over-tightened. In this case, you
need to turn the set screw [T] in
anti-clockwise direction to
decrease torque until the monitors
can be hovered at any position.
3. The monitors will drops
automatically if the set screw [T] is
over-loosen. In this case, you need
to turn the set screw [T] in
clockwise direction to increase
torque until the monitors can be
hovered at any position.
2X Cable tie
Tilt Adjustment
Step 5 Adjust the Tilt Angle and Manage the Cables
Tilt Adjustment
F1
T
Large Allen Key
Warning:
To avoid tipping, please be careful not to extend the monitor too far
backward. When you adjust the angle of the monitor, please make sure
the monitor is balanced to avoid instability of the center of gravity of
the base.
DeskDesk
Swivel
Note:
You can rotate the monitor or
swivel the arm manually.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
HUANUO HNCM12 Installation guide
- Category
- Flat panel desk mounts
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
HUANUO HNDPS Installation guide
-
-
-
-
-
-
-
-
-
