Kichler Lighting 52030BK User manual

Type
User manual
IS-52030-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
1) Aach arm[D] to upper plate of center tube assembly[A] by aligning hole
in top of arm with hole in plate. Insert screw[C] from top of plate through
holes and screw into nial[B] on underside of arm. Do not ghten. Repeat for
three (3) remaining arms.
2) Aach main frame[F] to arm[D] by aligning hole at boom of arm with hole
on top corner of main frame. Insert studded lock-up knob[E] through hole in
arm and screw into hole in main frame. Repeat for three (3) remaining arms.
Once main frame is secured to all four (4) arms, ghten screws from step 2.
3) Take threaded pipe[L] from parts bag and screw in screw collar loop[I], a
minimum of 6 mm (1/4”). Lock into place with hexnut[M].
4) Run another hexnut down threaded pipe almost touching rst hexnut.
Now screw threaded pipe into mounng strap[N]. Mounng strap must be
posioned with extruded thread faced into outlet box[P]. Threaded pipe
must protrude out the back of mounng strap. Screw third hexnut onto end
of threaded pipe protruding from back of mounng strap.
5) Connect mounng strap to outlet box using the strap mounng screws[O].
6) Unscrew the threaded ring[J] from screw collar loop. Take canopy[K] and pass
over screw collar loop. Approximately one half of the screw collar loop exterior
threads should be exposed. Adjust screw collar loop by turning assembly up or
down in mounng strap. Remove canopy.
7) Aer desired posion is found, ghten both top and boom hexnuts up
against the boom and top of the mounng strap.
8) Slip canopy over screw collar loop and thread on threaded ring. Aach chain[G]
to boom of screw collar loop by spreading one link and then closing the link.
9) Pass xture wire through large loop[H].
10) Screw large loop[H] onto threaded pipe aached to top of center tube
assembly[A]. Aach chain[G] to xture by spreading one link and then closing
the link.
11) Unscrew threaded ring[J], let canopy[K] and threaded ring slip down.
12) Weave electrical wire and ground wire through chain links[G] no more than
3 inches apart. Pass wire through screw collar loop[I], threaded ring[J],
canopy[K], threaded pipe[L], and into outlet box[P].
13) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a hole and two raised
dimples, wrap ground wire from outlet box around green ground screw,
and thread into hole.
b) On xtures where a cupped washer is provided, aach ground wire from
outlet box under cupped washer and green ground screw, then thread
into mounng strap.
If xture is provided with ground wire, connect xture ground wire to outlet
box ground wire with wire connector aer following the above steps. Never
connect ground wire to black or white power supply wires.
14) Make wire connecon. Reference chart below for correct connecons and
wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (See illus.)
Neutral Wire
15) Raise canopy to ceiling.
16) Secure canopy in place by ghtening threaded ring[J] onto screw collar
loop[I].
17) Insert recommended bulbs (Not supplied).
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
Fixture Diagram
Parts List
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main fusebox before
starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance with the Naonal Electrical
Code (NEC) and all local code specicaons. If you are not familiar with code
requirements, installaon by a cered electrician is recommended.
CLEANING:
Always be certain that electric current is turned o before cleaning.
• Only a so damp cloth should be used. Harsh cleaning products may damage
the nish.
Installaon Instrucons
[A] Center Tube
Assembly
[B] Finial
[C] Screw
[D] Arm
[E] Knob
[F] Main Frame
[G] Chain Links
[H] Large Loop
[I] Screw Collar Loop
[J] Threaded Ring
[K] Canopy
[L] Threaded Pipe
[M] Hexnut
[N] Mounting Strap
[O] Strap Mounting
Screws
[P] Outlet Box
G
I
K
P
N
M
O
L
J
H
C
D
E
B
A
F
  • Page 1 1
  • Page 2 2
  • Page 3 3

Kichler Lighting 52030BK User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI