2. Kichler Lighting
  3. 44022NBR

Kichler Lighting 44022NBR User manual

  • Hello! I am an AI chatbot trained to assist you with the Kichler Lighting 44022NBR User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
IS-44022-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
with extruded thread faced into outlet box[F]. Threaded
pipe must protrude out the back of mounng strap.
Screw third hexnut onto end of threaded pipe protruding
from back of mounng strap.
5) Connect mounng strap to outlet box using the strap
mounng screws[E].
6) Unscrew the threaded ring[G] from screw collar
loop. Take canopy[H] and pass over screw collar loop.
Approximately one half of the screw collar loop exterior
threads should be exposed. Adjust screw collar loop by
turning assembly up or down in mounng strap. Remove
canopy.
7) Aer desired posion is found, ghten both top and
boom hexnuts up against the boom and top of the
mounng strap.
8) Slip canopy over screw collar loop and thread on
threaded ring. Aach chain[I] (with xture connected) to
boom of screw collar loop. Unscrew threaded ring, let
canopy and threaded ring slip down.
9) Adjust chain to desired length by removing chain links
and aach chain to xture with one open link[J], close
the open links by wrapping with a towel and squeezing
closed using pliers.
10) Weave electrical wire and ground wire through chain
links no more than 3 inches apart. Pass wire through
threaded ring, canopy, screw collar loop, threaded pipe
and into outlet box.
11) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a
hole and two raised dimples, wrap ground wire from
outlet box around green ground screw, and thread
into hole.
b) On xtures where a cupped washer is provided,
aach ground wire from outlet box under cupped
washer and green ground screw, and thread into
mounng strap.
If xture is provided with ground wire, connect xture
ground wire to outlet box ground wire with wire
connector aer following the above steps. Never connect
ground wire to black or white power supply wires.
12) Make wire connecon. Reference chart below for correct
connecons and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (see illus.)
Neutral Wire
13) Raise canopy to ceiling.
14) Secure canopy in place by ghtening threaded ring onto
screw collar loop.
15) Lower glass[M] over the light sockets of the lower arm
secon[O] and thread on the socket ring[N] to secure
into place. Repeat for the other sockets.
16) Insert recommended bulbs. (Not supplied)
17) Lower the shades[P] onto the installed glass.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
Fixture Diagram
Parts List
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance
with the Naonal Electrical Code (NEC) and all local code
specicaons. If you are not familiar with code requirements,
installaon by a cered electrician is recommended.
Installaon Instrucons
[A] Threaded
Pipe
[B] Screw Collar
Loop
[C] Hexnut
[D] Mounting
Strap
[E] Strap
Mounting
Screws
[F] Outlet Box
[G] Threaded
Ring
[H] Canopy
[I] Chain
[J] Chain Link
[K] Large Loop
[L] Main Body
[M] Glass
[N] Socket Ring
[O] Lower Arm
Section
[P] Shades
[Q] Stem
1) Run xture wire from the lower arm secon[O] through
the stem[Q] of the main body[L] if xture wire has
not already been installed to main body. Take the
main body[L] and rotate into place onto the lower
arm secon[O], rotate the center pieces unl desired
posion is achieved.
2) Take the large loop[K] and run the wires through its
center and thread onto the main body[L].
3) Take threaded pipe[A] from parts bag and screw in
screw collar loop[B] a minimum of 6 mm (1/4”). Lock
into place with hexnut[C].
4) Run another hexnut down threaded pipe almost
touching rst hexnut. Now screw threaded pipe into
mounng strap[D]. Mounng strap must be posioned
Installaon Instrucons (connued)
L
N
F
D
C
E
A
H
B
G
I
J
J
K
P
M
O
Q
Page is loading ...
IS-44022-CB
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
with extruded thread faced into outlet box[F]. Threaded
pipe must protrude out the back of mounng strap.
Screw third hexnut onto end of threaded pipe protruding
from back of mounng strap.
5) Connect mounng strap to outlet box using the strap
mounng screws[E].
6) Unscrew the threaded ring[G] from screw collar
loop. Take canopy[H] and pass over screw collar loop.
Approximately one half of the screw collar loop exterior
threads should be exposed. Adjust screw collar loop by
turning assembly up or down in mounng strap. Remove
canopy.
7) Aer desired posion is found, ghten both top and
boom hexnuts up against the boom and top of the
mounng strap.
8) Slip canopy over screw collar loop and thread on
threaded ring. Aach chain[I] (with xture connected) to
boom of screw collar loop. Unscrew threaded ring, let
canopy and threaded ring slip down.
9) Adjust chain to desired length by removing chain links
and aach chain to xture with one open link[J], close
the open links by wrapping with a towel and squeezing
closed using pliers.
10) Weave electrical wire and ground wire through chain
links no more than 3 inches apart. Pass wire through
threaded ring, canopy, screw collar loop, threaded pipe
and into outlet box.
11) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a
hole and two raised dimples, wrap ground wire from
outlet box around green ground screw, and thread
into hole.
b) On xtures where a cupped washer is provided,
aach ground wire from outlet box under cupped
washer and green ground screw, and thread into
mounng strap.
If xture is provided with ground wire, connect xture
ground wire to outlet box ground wire with wire
connector aer following the above steps. Never connect
ground wire to black or white power supply wires.
12) Make wire connecon. Reference chart below for correct
connecons and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (see illus.)
Neutral Wire
13) Raise canopy to ceiling.
14) Secure canopy in place by ghtening threaded ring onto
screw collar loop.
15) Lower glass[M] over the light sockets of the lower arm
secon[O] and thread on the socket ring[N] to secure
into place. Repeat for the other sockets.
16) Insert recommended bulbs. (Not supplied)
17) Lower the shades[P] onto the installed glass.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
Fixture Diagram
Parts List
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance
with the Naonal Electrical Code (NEC) and all local code
specicaons. If you are not familiar with code requirements,
installaon by a cered electrician is recommended.
Installaon Instrucons
[A] Threaded
Pipe
[B] Screw Collar
Loop
[C] Hexnut
[D] Mounting
Strap
[E] Strap
Mounting
Screws
[F] Outlet Box
[G] Threaded
Ring
[H] Canopy
[I] Chain
[J] Chain Link
[K] Large Loop
[L] Main Body
[M] Glass
[N] Socket Ring
[O] Lower Arm
Section
[P] Shades
[Q] Stem
1) Run xture wire from the lower arm secon[O] through
the stem[Q] of the main body[L] if xture wire has
not already been installed to main body. Take the
main body[L] and rotate into place onto the lower
arm secon[O], rotate the center pieces unl desired
posion is achieved.
2) Take the large loop[K] and run the wires through its
center and thread onto the main body[L].
3) Take threaded pipe[A] from parts bag and screw in
screw collar loop[B] a minimum of 6 mm (1/4”). Lock
into place with hexnut[C].
4) Run another hexnut down threaded pipe almost
touching rst hexnut. Now screw threaded pipe into
mounng strap[D]. Mounng strap must be posioned
Installaon Instrucons (connued)
L
N
F
D
C
E
A
H
B
G
I
J
J
K
P
M
O
Q
Page is loading ...
/