IS-52077-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
9) Take threaded pipe[A] from parts bag and screw in screw collar loop[B] a
minimum of 6 mm (1/4”). Lock into place with hexnut[C].
10) Run another hexnut down threaded pipe almost touching rst hexnut.
Now screw threaded pipe into mounng strap[D]. Mounng strap must be
posioned with extruded thread faced into outlet box[E]. Threaded pipe
must protrude out the back of mounng strap. Screw third hexnut onto end
of threaded pipe protruding from back of mounng strap.
11) Connect mounng strap[D] to outlet box using the strap mounng screws[J].
12) Unscrew the threaded ring[F] from screw collar loop. Take canopy[G] and pass
over screw collar loop. Approximately one half of the screw collar loop exterior
threads should be exposed. Adjust screw collar loop by turning assembly up or
down in mounng strap. Remove canopy.
13) Aer desired posion is found, ghten both top and boom hexnuts up
against the boom and top of the mounng strap.
14) Slip canopy over screw collar loop and thread on threaded ring. Aach open
locking chain link[H] (with xture connected) to boom of screw collar loop.
Close the open chain link by threading the nut down onto the link end. Unscrew
threaded ring, let canopy and threaded ring slip down.
15) Pass electrical wire and ground wire through chain link[H], threaded ring[F],
canopy, screw collar loop, threaded pipe and into outlet box.
16) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a hole and two raised
dimples, wrap ground wire from outlet box around green ground screw,
and thread into hole.
b) On xtures where a cupped washer is provided, aach ground wire from
outlet box under cupped washer and green ground screw, then thread
into mounng strap.
If xture is provided with ground wire, connect xture ground wire to outlet
box ground wire with wire connector aer following the above steps. Never
connect ground wire to black or white power supply wires.
17) Make wire connecon. Reference chart below for correct connecons and
wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (See illus.)
Neutral Wire
18) Raise canopy to ceiling.
19) Secure canopy in place by ghtening threaded ring onto screw collar loop.
20) Install the recommended bulbs (not supplied).
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
Fixture Diagram
Parts List
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main fusebox before
starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance with the Naonal Electrical
Code (NEC) and all local code specicaons. If you are not familiar with code
requirements, installaon by a cered electrician is recommended.
CLEANING:
• Always be certain that electric current is turned o before cleaning.
• Only a so damp cloth should be used. Harsh cleaning products may damage
the nish.
Installaon Instrucons
1) Aach screen[P] to mounng bracket[Q] using mounng screws[R] as
shown (one screw on top, one screw on boom). Repeat for remaining two
(2) screens.
2) Aach center tube aached to upper frame[M] to lower frame[N] by
screwing end of short threaded tube[K] into coupling on top of main frame.
3) Aach arm on upper frame[M] to mounng bracket[Q] by inserng threads
on lower end of arm into inner hole on mounng bracket[Q] and out of outer
hole on mounng bracket.
4) Secure arm to mounng bracket by screwing nial[O] onto threads on end of
arm protruding out of mounng bracket.
5) Repeat steps 3 and 4 for remaining two (2) arms.
6) Pass xture wire from the upper frame[M] through a stem[L] and short
threaded tube[K] and screw stem into coupling on top of upper frame[M].
NOTE: Thread locking compound must be applied to all stem threads as
noted with symbol (4) to prevent accidental rotaon of xture during
cleaning, relamping, etc.
7) Pass xture wire through desired amount of stems and screw stems together
using supplied short threaded tubes.
8) Pass xture wire from last stem through loop[I]. Thread loop onto end of last
stem.
Installaon Instrucons (connued)
[A] Threaded Pipe
[B] Screw Collar Loop
[C] Hexnut
[D] Mounting Strap
[E] Outlet Box
[F] Threaded Ring
[G] Canopy
[H] Locking Chain Link
[I] Loop
[J] Strap Mounting
Screws
[K] Threaded Tubes
[L] Stem
[M] Upper Frame
[N] Lower Frame
[O] Finial
[P] Screen
[Q] Mounting Bracket
[R] Mounting Screws
C
J
A
G
B
F
H
►
I
L
K
►
►
►
M
D
N
PP
Q
R
R
O
O
K
B
I
H
1
2
3
Kichler Lighting 52078PAL User manual
Kichler Lighting 52079PAL User manual
Kichler Lighting 52030BK User manual
Kichler Lighting 52209PN User manual
Kichler Lighting 52209PN User manual
Kichler Lighting 52029BK User manual
Kichler Lighting 52162BK User manual
Kichler Lighting 52234BK User manual
Kichler Lighting 59031BKTLED User manual
Kichler Lighting 59030BKTLED User manual
Kichler 52349BK Operating instructions
urban ambiance ULB2311 Installation guide
