BEA UL LISTED GATELOCKS User guide

Type
User guide

BEA UL LISTED GATELOCKS

These locks provide a strong magnetic bond (1200 lbs.) to keep sliding or swing gates securely locked. The weather-resistant stainless steel housing makes them suitable for outdoor use. They come with a conduit fitting for easy wiring.

Features:

  • Magnetic holding force: 1200 lbs.
  • Input voltage: 12 or 24 VDC
  • Current: 500 mA @ 12 VDC, 250 mA @ 24 VDC
  • Contact rating: 0.250 A @ 12 V, 0.125 A @ 24 V
  • Dimensions: 8.750”L X 2.500”H X 1.625”D
  • Conduit fitting: 3/4 inch NPS conduit fitting, 14 Threads per inch

Possible use cases:

BEA UL LISTED GATELOCKS

These locks provide a strong magnetic bond (1200 lbs.) to keep sliding or swing gates securely locked. The weather-resistant stainless steel housing makes them suitable for outdoor use. They come with a conduit fitting for easy wiring.

Features:

  • Magnetic holding force: 1200 lbs.
  • Input voltage: 12 or 24 VDC
  • Current: 500 mA @ 12 VDC, 250 mA @ 24 VDC
  • Contact rating: 0.250 A @ 12 V, 0.125 A @ 24 V
  • Dimensions: 8.750”L X 2.500”H X 1.625”D
  • Conduit fitting: 3/4 inch NPS conduit fitting, 14 Threads per inch

Possible use cases:

2 Specications
UL GATE LOCKS
USER’S GUIDE
MAGNETIC UL LOCK FOR GATES
1 Description
DESCRIPTION SPECIFICATION
Input Voltage: 12 or 24 VDC
Current: 500 mA @ 12 VDC
250 mA @ 24 VDC
Contact Rating: 0.250 A @ 12 V
0.125 A @ 24 V
Dimensions: 8.750”L X 2.500”H X 1.625”D
Conduit ftting:
(10GL1200R only)
3/4 inch NPS conduit tting
14 Threads per inch
Cerication: UL/CUL
BEA’s Gate-Lock provides an effective magnetic
bond (1200 lbs.) to keep sliding or swing gates
locked for your security needs. The attractive,
weather resistance stainless steel housing makes
this lock suitable for external applications.
3 Precautions
Shut off all power before attempting any wiring procedures.
Maintain a clean and safe environment when working in public areas.
Constantly be aware of pedestrian trafc around the door area.
Always stop pedestrian trafc through the doorway when performing tests that may result in unexpected reactions by the
door.
ESD electrostatic discharge: Circuit boards are vulnerable to damage by electrostatic discharge. Before handling any board
ensure you dissipate your body’s charge.
Always check placement of all wiring before powering up to insure that moving door parts will not catch any wires and cause
damage to equipment.
Ensure compliance with all applicable safety standards (i.e. ANSI A156.10) upon completion of installation.
DO NOT attempt any internal repair of the sensor. All repairs and/or component replacements must be performed by BEA,
Inc. Unauthorized disassembly or repair:
1. May jeopardize personal safety and may expose one to the risk of electrical shock.
2. May adversely affect the safe and reliable performance of the product will result in a voided product warranty.
4 Pre Installation Check
1. When preparing to wire multiple devices together for a ‘system’ conguration, it is best to ensure the correct operation of each device
independently before starting to help reduce troubleshooting time later in the event of a discrepancy.
2. Prior to installing any equipment, ensure the correct line voltage and stability. When applying equipment on a new installation utilizing new
electrical supply circuits, always ensure that correct line voltage exists and is stable. Remember to shut the power back off after this is
checked and before performing any wiring to the system.
5 Installation
1. Determine the desired location for mounting the Gate-Lock assembly on the gate and/or post.
NOTE: Position the maglock end with the conduit tting (3/4” female) relative to the location of electrical wiring.
75.5668.05 20160915 Page 1 of 2
FRONT MOUNT
10GL1200R
LZ BRACKET
10LZBRGATE1200
10GL1200R / 10GL1200SR
FRONT MOUNT
10GL1200R
2. Drill the mounting holes for the bracket (armature and/or magnet, depending on conguration) per FIGURE 1.
NOTE: If applicable, drill two (2) 1/4” holes, 9/16” deep, 3 1/4” from
armature mounting screw hole for anti-spin pin locations.
Drive anti-spin pins into armature holes using a rubber mallet.
3. Attach bracket(s) rmly with mounting machine/sheet metal screws.
To reduce the effects of excessive vibrations on bracket attachment,
apply Locktite/Threadlocker (not included) to screws during installation.
CAUTION: FAILURE TO PROPERLY SECURE THE ARMATURE COULD
RESULT IN SERIOUS INJURY OR SECURITY BREACH.
4. With washers and spacers included (See FIGURE 2), rmly tighten
armature mounting screws to bracket with hex wrench.
5. Attach magnet assembly to bracket or post with four (4) socket head
screws or self taping screws with anti-tamper plugs.
6. Close the gate and verify magnet face and
armature are making full contact over entire
surface. Make adjustments as required.
Page 2 of 2 75.5668.05 20160915
5 Installation (Continued)
7 Company Contact
6 Wiring
12VDC
NOTE: For 12V source; connect RED/BLACK
wires and connect GREEN/ORANGE wires.
For
24V source; short BLACK/GREEN wires
and connect RED and ORANGE wires .
BROWN (COM)
YELLOW (NO)
BLUE (NC)
+
RED
BLACK
-
GREEN
ORANGE
+
RED
BLACK
-
GREEN
ORANGE
24VDC LOCK STATUS
Lock Status contacts change status when
the bonding occurs.
Transient voltage suppressor (TVS) should
be placed as directed.
(NON-BONDED STATE)
TVS TVS
BEA recommends a UL Power Supply.
HOLE FOR GUIDE PIN
HOLE FOR NUT
RUBBER WASHER
STEEL WASHER
ARMATURE PLATE
SCREW M8 (35MM)
GUIDE PIN
POST
SPACER (11/16”)
NUT
NOTE: DO NOT over-tighten armature plate. Rubber washer is designed
to allow the armature plate to automatically adjust position
for best mating position between lock and armaure plate.
STEEL WASHER
HOLLOW TUBE SOLID CORE
FIGURE 1C
REINFORCED TUBE
FIGURE 1B
1. Drill an 5/16" diameter hole through gate.
2. Enlarge the 5/16” hole to 5/8” from sex
nut side only.
1. Drill an 5/16" diameter hole through gate.
2. Enlarge the 5/16” hole to 15/32” to a depth
of 1 1/2” from sex nut side only.
1. Drill an 17/64" diameter hole and
tap for M8-1.25 thread.
FIGURE 1A
DOOR
SPACER
SEX
NUT
5/8"
MOUNTING
SCREW
GATE LOCK
BRACKET
1-3/4"
M8-1.25 THREAD
MOUNTING
SCREW
GATE LOCK
BRACKET
MOUNTING
SCREW
15/32"
1 1/2"
SEX
NUT
GATE LOCK
BRACKET
1/2"
7/8"
ARMATURE PLATE
ASSEMBLY
FIGURE 2
24/7 Tech Support: 1-800-407-4545 | Customer Service: 1-800-523-2462 | General Tech Questions: T[email protected] | Tech Docs: www.beasensors.com
  • Page 1 1
  • Page 2 2

BEA UL LISTED GATELOCKS User guide

Type
User guide

BEA UL LISTED GATELOCKS

These locks provide a strong magnetic bond (1200 lbs.) to keep sliding or swing gates securely locked. The weather-resistant stainless steel housing makes them suitable for outdoor use. They come with a conduit fitting for easy wiring.

Features:

  • Magnetic holding force: 1200 lbs.
  • Input voltage: 12 or 24 VDC
  • Current: 500 mA @ 12 VDC, 250 mA @ 24 VDC
  • Contact rating: 0.250 A @ 12 V, 0.125 A @ 24 V
  • Dimensions: 8.750”L X 2.500”H X 1.625”D
  • Conduit fitting: 3/4 inch NPS conduit fitting, 14 Threads per inch

Possible use cases:

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI