Leviton OSSMT-GDW Operating instructions

Brand: Leviton

Model: OSSMT-GDW

Type: Operating instructions

This manual is also suitable for

WARNINGS AND CAUTIONS:

• Tobeinstalledand/orusedinaccordancewithappropriateelectricalcodesandregulations.

• Ifyouareunsureaboutanypartoftheseinstructions,consultaqualiedelectrician.

• Controllingaloadinexcessofthespeciedratingswilldamagetheunitandposeriskofre,electricshock,personalinjuryordeath.

Checkyourloadratingstodeterminesuitabilityforyourapplication.

• Donotinstallthisunittocontrolareceptacle.

WARNINGS AND CAUTIONS:

• TheOSSMT-GDOccupancySensorisintendedtoreplaceastandardsingle-poleDecorawallswitch.

• Donottouchthesurfaceofthelens.Cleanoutersurfacewithadampclothonly.

• Disconnectpoweratcircuitbreakerorfusewhenservicing,installingorremovingxture.

• Usethisdeviceonlywithcopperorcoppercladwire.WithaluminumwireuseonlydevicesmarkedCO/ALRorCU/AL.

SinglePole(OneLocation)orMulti-Location

Multi-Technology Designer Wall Switch Occupancy Sensor

California Title 24 2005 Compliant

Cat. No. OSSMT-GD

Incandescent/Tungsten:800W@120VBallast:1200VA@120VBallast:2700VA@277VMotor:1/4hp@120V

Operating Temperature Range:0°Cto50°C

Relative Humidity:20%to90%non-condensing

No Minimum Load Required

Compatiblewithincandescentlamps,low-voltagelightingwithelectronicandmagnetictransformers,electronicandmagneticuorescentballasts,andfans.

INSTALLATION INSTRUCTIONS

TOOLS NEEDED TO INSTALL YOUR SENSOR

Slotted/PhillipsScrewdriver ElectricalTape 

Pliers   Cutters  

SmallSlottedScrewdriver

• Leviton’sDecora

styledesign

• Sensorcanbegangedtogetherwithotherunitsinamultiple-switch

wallplate.

• Self-AdaptiveTechnologyadjuststooccupancypatternsofusein

autoadaptmode.

• TheAdaptingTime-outwalk-throughfeaturepreventslightsfrom

remainingONforanextendedperiodafteronlyamomentary

occupancy.

• Switchesasingleloadcircuit.

• OnePush-ButtonwhichprovidesmanualON/OFFswitchingat

anytime.

• Adjustablehorizontaleldofview.

• IntegratedphotocellpreventslightsfromturningONwhenroomis

adequatelyilluminatedbynaturallight.

• TrueZero-Crossrelayprovidesmaximumcontactlifeand

compatibilitywithelectronicballasts.

• Dualdetectiontechnology,bothPassiveInfraredandUltrasonic.

CanbeconguredasUltrasonicOnlybydisablingPassive

Infrared.

Leviton'sDesignerMulti-TechnologyWallSwitchOccupancySensor,

Cat.No.OSSMT-GD,isdesignedtodetectmotionusingthepassive

infrared(PIR)sensorfromsources(suchasapersonenteringa

room)withinitseld-of-view(monitoredspace)andautomatically

switchlightsON.TheOccupancySensorsensesmotionwithinits

maximumcoverageareaof2400sq.ft(223m

).Theultrasonic(US)

sensorsworkwiththePIRtokeepthelightsONwhenoccupied.The

controlledlightswillremainONuntilnomotionisdetectedandthe

scheduledtime-delayhasexpired,atwhichpointthelightswillbe

turnedOFF.Inadaptingtime-outmodethesensoradaptsitstime

delaysettingstotheoccupancypatternsofaroom.

TheCat.No.OSSMT-GDisanOccupancySensorthatisdesignedto

controlasinglelightingcontrolcircuitandprovidetheenergysavings

ofanoccupancysensor.Thisdevicedoesnotcontainaneutral

conductor.Itisintendedforuseinretrotapplicationswhereaneutral

isnotavailableinthewallbox.

TheOSSMT-GDisasinglerelaydevice,whichcanbeAutoONor

ManualON.ThedevicecontainsaphotocellthatprovidesanAmbient

LightHoldOfffunction.ThedeviceiscongurableforeitherUltrasonic

withPIRorUltrasonicOnlymodesofoperation.

Cat. No. OSSMT-GD is ETL listed, cETL listed and conforms to

California Title 24 requirements.

ThePIROccupancySensorusesasmallsemiconductorheatdetector

thatresidesbehindamulti-zoneopticallens.ThisFresnellens

establishesdozensofzonesofdetection.TheSensorissensitivetothe

heatemittedbythehumanbody.InordertoinitiallytriggertheSensor,

thesourceofheatmustmovefromonezoneofdetectiontoanother.

Thedeviceismosteffectiveinsensingmotionacrossitseld-of-view

anditislesseffectivesensingmotiontowardsorawayfromitseld-of-

view).Keepthisinmindwhenselectingtheinstallationlocation(refer

to Field-of-View diagrams).

TheUSOccupancySensorusesanon-audible,highfrequency(40kHz)

tosenseDopplershiftscausedbymotioninthespace.TheUSismore

sensitivetosmallmotionanddoesnotrelyonlineofsightfordetection.

Ifbothsensorshavenotdetectedanymotionforthesettimeoutperiod,

therelayanditscorrespondingloadwillbeturnedOFF.

Notethatoccupancysensorsrespondtorapidchangesintemperature,

socareshouldbetakennottomountthedevicenearaclimatecontrol

source(i.e.radiators,airexchanges,andairconditioners).Hotorcold

draftswilllooklikebodymotiontothedeviceandwilltriggeritiftheunit

ismountedtooclose.It is recommended to mount the Occupancy

Sensor at least 6 feet away from a climate control source.

Inaddition,itisalsorecommendedNOTtomounttheOccupancySensor

directlyunderalargelightsource.Largewattagebulbs(greaterthan

100Wincandescent)giveoffalotofheatandswitchingthebulbcauses

atemperaturechangethatcanbedetectedbythedevice.Mountthe

OccupancySensoratleast6ft.awayfromlargebulbs.Ifitisnecessary

tomountthedevicecloser,lowerthewattageofthebulbdirectly

overhead.

WARNING:TO AVOID FIRE, SHOCK, OR DEATH; TURN

OFF POWER atcircuitbreakerorfuseandtestthatpoweris

offbeforewiring!

Step 1

/./&&

/./&&/./&&

/./&&

• Pulloffpre-cutinsulationfromsensorleads.

• Makesurethattheendsofthewiresfromthewallboxarestraight

(cut if necessary).

• Removeinsulationfromeachwireinthewallboxasshown.

Preparing and connecting wires:

9/16"

(1.4 cm)

Strip Gage

(measure bare

wire here)

Cut

(if necessary)

Step 3

INSTALLING YOUR SENSOR

NOTE:UsecheckboxeswhenStepsarecompleted.

Installing your Sensor – Single-Pole Application:

Step 4

Identifying your wiring application

(most common):

Step 2

WIRING SENSOR:

Connect wires per WIRING DIAGRAM as follows:Screwwireconnector

onclockwisemakingsuretherearenobareconductorsbelowthewire

connectors.Secureeachconnectorwithelectricaltape.

• GreenorbarecopperwireinwallboxtoGreenlead.

• LineHotwallboxwiretoBlacklead.

• LoadwallboxwiretoBluelead.

NOTE: Allow 1 minute for warm-up after connecting and energizing.

WIRING SENSOR 1:

Connect wires per WIRING DIAGRAM as follows:

• GreenorbarecopperwireinwallboxtoSensor1Greenlead.

• LineHot(common)wallboxwireidentied(tagged)whenremovingold

switchandFirsttravelerfromSensor2toSensor1Blacklead.

• SecondTravelerwallboxwirefromSensor2toSensor1Bluelead.

WIRING SENSOR 2:

Connect wires per WIRING DIAGRAM as follows:

• GreenorbarecopperwireinwallboxtoSensor2Greenlead.

• Loadwallboxwireidentied(tagged)whenremovingoldswitchand

SecondTravelerfromSensor1toSensor2Bluelead.

• FirstTravelerLineHotfromSensor1toSensor2Blacklead.

NOTE: Allow 1 minute for warm-up after connecting and energizing.

Step 5

NOTE:

TheCat.No.OSSMT-GDrequiresagroundwiretooperateproperly.

Ifthereisnogroundwire,ensureelectricalboxisgroundedandattach

groundwiretoboxwithascrew.Ifthegroundwireisoatingthisdevice

willnotwork.

NOTE:TheCat.No.OSSMT-GDrequiresagroundwiretooperate

properly.Ifthereisnogroundwire,ensureelectricalboxisgroundedand

attachgroundwiretoboxwithascrew.Ifthegroundwireisoatingthis

devicewillnotwork.

NOTE:Sensor1

must

beinstalledinawallboxthathasbothaLINEHot

andaGroundconnection.Sensor2

must

beinstalledinawallboxthat

hasbothaLoadandaGroundconnection.

Ifyouareunsureaboutanypartoftheseinstructions,consultaqualied

electrician.

NOTE:EithersensorcanturnthelightsON.Bothsensorsmusttimeout

toOFForbothmanualbuttonsmustbepressedforthelightstogoOFF

DESCRIPTION

DI-0XX-OSSMT-00A

FEATURES

3-Way

1. LineorLoad(Seeimportant*

instruction)

2. Ground

3. FirstTraveler–notecolor

4. SecondTraveler–notecolor

Single-Pole

1.Line(Hot)

2.Ground

3.Load

IMPORTANT:For3-Wayapplications,notethatoneofthescrew

terminalsfromtheoldswitchbeingremovedwillusuallybeadifferent

color(Black)orlabeledCommon.Tagthatwirewithelectricaltapeand

identifyasthecommon(LineorLoad)inbothswitchwallboxes.

Sensor

Green

Blue

Black

Black (Hot)

Neutral (White)

Load

Sensor

Black

White

Blue

Green

Ground

Line

120VAC, 60Hz

Installing your Sensor – 3-Way Wiring Application:

Black (Hot)

Neutral (White)

Load

Sensor 2 Sensor 1

Black

White

Blue Blue

Green

Ground

Green

Ground

Line

120VAC, 60Hz

NOTE:Dresswireswithabendasshownindiagramtorelievestress

whenmountingdevice.

•

 Positionallwirestoprovideroominoutletwallboxfordevice.

• Partiallysecuredeviceusinglongmountingscrewsprovided.

• Restorepoweratcircuitbreakerorfuse.

NOTE: Allow 1 minute for warm-up after energizing.

NOTE:AllmodelsoftheOSSMT-GDarefactorypresettowork

withoutanyadjustments.Ifnecessary,adjusttheBlindersandPIR

RangeControltostopanyunwantedactivationofthelights(refer

to FEATURES section).

• ForadditionalTimeControlSettings(refer to the SETTINGS section).

NOTE:ToavoidPERMANENTDAMAGEtotheunit,becareful

NOTTOOVERTURNthecontrolknobsorleverswhensettingthe

Sensor.Thecontrolscanbeaccessedbyremovingthewallplate

(ifapplicable)andcontrolpanelcover(refer to Control Panel

Diagram).Useasmallstraightbladescrewdrivertoadjustknobs

andblinderlevers.

NOTE: DO NOT pressinonblinderleversoruseexcessiveforce

(refer to Control Panel Diagram).

• AttachtheControlPanelcoverwhenthedesiredsettingsare

complete.

If lights do not turn ON, refer to the TROUBLESHOOTING section.

Testing your Sensor prior to completely

mounting in wall box:

Step 6

NOTE: To access control settings, remove the control panel cover.

If necessary, remove the warning label that covers the adjustment

dials (refer to Control Panel Diagram).

Factory Settings:Thesensorisshippedfromthefactorytoworkin

almostallsituations,withoutanyaddedadjustments.Thefactorysettings

are:Blindersopen,10minutesxedTime-Out,LightsalwaysturnON

regardlessofexistinglightlevels,Mediumpassiveinfrared(PIR)range,

andHighUltrasonicrange.ThePIRandultrasonictechnologiesareboth

active.

Blinders:Theblindersaretwoindependentshuttersthatcannarrow

theeld-of-viewfromamaximumof180°downto32°.Theblindersare

operatedbymovingtheblinderleverstowardsorawayfromthecenterof

theSensor.Theblinderleverscanbefoundabovethecontroldialsinthe

controlpanel(refer to Control Panel Diagram).

Time-Outs:TheSensorhasthreetypesofTime-Outs:Fixed,Adapting,

andWalkthrough.

 • FixedTime-Out:ThevalueofthisTime-Outisuserselected

throughtheuseoftheTimeControlSetting(refertoControlPanel

DiagramandTime-OutSettings).

FEATURES

Mounting

screws

(2 places)

Wall surface

Sensor

Sensor 1

Green

Blue

Black

Sensor 2

Green

Blue

Black

 • Adapting Time-Out:Whenactivated,thevalueofthisTime-Out

(30minutes)ischangedbytheSensorbasedonroomoccupancy

andlightingconditions.

 • Walk-through Time-Out:ThevalueofthisTime-Outispresetto

2.5minutesandonlyexistsintheAdaptingTime-Outmode.

Fixed Time Delay:ThexedTime-Outvalueisselectedbyrotatingthe

TimeControldial.Therearefour(4)valuesfromwhichtochoose.Each

markaroundthedialcorrespondstoadifferentvalueasindicatedbelow

(refer to Control Panel Diagram).

 NOTE:Alltimedurationsareapproximatewithin±10seconds.

Adapting Time Delay:TheSensorhasbuiltinadaptingintelligencethat

changestheAdaptingTime-Outdurationinresponsetotheoccupancy

conditionsoftheroomitisinstalledin.IftheSensordetects“large,”

infrequentmotionitwillINCREASEtheAdaptingTime-Outduration.If

theSensordetects“large,”frequentmotion(asinseveralpersonsina

roomduringameeting),itwillDECREASEthetime-outdurationonlyifit

wasNEVERincreased(thisisbecausethebuiltinintelligencewillalways

proceedinthedirectionof“increasing”adaptingTime-Outonceithas

increaseditforanyoftheoccupancyconditionssensed).TheAdapting

Time-Outdurationwillrangefrom10to30minutesintimeplustheWalk-

ThroughTimeDelay.

Walk-Through Time Delay:Thewalk-throughfeaturewhichisonly

activeintheAdaptingTime-Outmode,isusefulwhenaroomis

momentarilyoccupied.Withthisfeature,theSensorwillturnthelights

OFFshortlyafterthepersonleavestheroom.Thewalk-throughfeature

worksinthefollowingmanner:Whenapersonenterstheroom,thelights

willturnON.Ifthepersonleavestheroombeforethewalk-throughtime-

outof2.5minutes,theSensorwillturnthelightsOFFafter2.5minutes.If

thepersonstaysintheroomforlongerthan2.5minutes,theSensorwill

insteadusethestoredAdaptingTime-OutDelaysetting.

IftheSensordetectsmotionwithin30secondsafterthelightsturnOFF,

itwillturnthelightsONandincreasethetime-outvalueby1.5timesthe

existingvalue.

TheAdaptingTime-Outmayberesettothebasevalueof30minutesby

rotatingtheTimeControltoanewtimeselectionvalueandthenbackto

theAdaptingTime-Outvalue(refer to Control Panel Diagram).

Ambient Light Override:TheAmbientLightOverrideisusedtokeep

thelightsOFFifthereisalreadyenoughnaturallightintheroom.

Forproperoperation,theAmbientLightOverrideadjustmentmustbe

performedwhenthereisenoughnaturallight(refer to the SETTINGS

section).Iftheadjustmentismadewhenthereislessnaturallight,the

lightsmaynotturnONeventhoughtheyareneededandwillrequire

manualactivationofthepush-buttonstoturnthelightsON.

NOTE:Theambientlightlevelinthecenterofaroomwillbedifferent

thanthelevelatthewallwheretheswitchislocated.

Ambient Light Dial:Theambientlightsettingisadjustedwiththe

AmbientLightDial(refer to Control Panel Diagram).TurningtheLight

Dialfullycounter-clockwise(CCW),setstheSensortomanualONmode

(seefollowingsection).IfthelightcontrolisinthefullyCWposition,the

lightswillturnONwhenevermotionisdetected,eveninfulldaylight.

IntermediatesettingswillcausethelightstoturnONonlywhenthe

ambientlightisbelowthelevelselectedbythelightcontrol.

NOTE:WhenthesettingisattheminimumCCWlevel,thelightswill

stayOFFwhentheroomisdim.Whenthesettingisatthemaximum

levelclockwise(CW),thelightswillturnONwhentheroomisbright.

Manual ON Mode:WhenthelightcontrolisinthefullyCCWposition

thelightswillneverautomaticallyturnON.Inthismodethelightsneed

tobemanuallyturnedONbythepush-button,andwillturnOFFwiththe

absenceofmotion.

PIR RANGE:TodecreasePIRdetectionrangeandsensitivity,rotatethe

knobCCW(refer to Control Panel Diagram).Thedetectionrangecan

beadjustedfrom100%downto30%.

ULTRASOUND (US) SENSITIVIY AND PIR DISABLE:USsensitivity

canbeadjustedtoHIGH-MEDIUM-LOWbyholdingtheONbuttonfor

15seconds.TheLEDwillashtorepresenttheUltrasonicsensitivity

andPIRstatus.TappingtheONbuttonduringthedesiredLEDash

indicationwillsettheUltrasonicsensitivityandPIRstatus.Usethe

followingchart:

TIME

RANGE

BLINDERS

LIGHT

Slash Mark

Blinder adjustment levers

Control Panel Cover

PUSH BUTTON(S)

Cat.No.OSSMT-GDxhasasinglepush-buttonswitchthattogglesthe

relayanditscorrespondingload,ONandOFF(refer to ﬁgure).Ifthe

relayisOFF,therelaywillturnONwhenthepush-buttonispressed,

andremainONinthepresenceofmotion.Intheabsenceofmotion,the

SensorUnitwillTime-OutandturntherelayOFF.

NOTES:

• TheMotionIndicatorLEDwillblinkeverysecondwhilemotion

isdetected.AredblinkrepresentsPIRdetection,agreenblink

representsUltrasonicdetection.

• WhentheTime-OutexpiresandtherelayturnsOFFa30second

vacancyconrmationexisttoturntherelaybackON.Afterthistime

thedevicewillbeplacedintoalowerdetectionthresholdmode.

• InManual-ONmode,thebuttonmustbepressedtoturnthelightsON.

Intheabsenceofmotion,theunitwillTime-OutandturnthelightsOFF.

• IfManual-Onmodeisdesired,keeptheLightknobinthefully

counter-clockwise(CCW)position.

NOTE:ToavoidPERMANENTDAMAGEtotheunit,becarefulNOT

TOOVERTURNoruseexcessiveforcewhensettingthecontrol

knobsorleversofCatNo.OSSMT-GD.Useasmallstraightblade

screwdrivertoadjusttheknobsandyourngertoadjusttheblinder

levers.

1. RemoveDecora

wallplateandControlPanelCoverfromSensor.

2. RotatetheTimedialtoselectthedesiredxedTime-Outvalue.

3. IftheSensorisinstalledwithin6feetofanairduct,rotatetheRange

Control1/4turncounter-clock-wise(CCW).

4. Set the Ambient Light Level - AMBIENT LIGHT:Cat.No.OSSMT-

GDhasanadjustmenttodetermineatwhatminimumambientlight

leveltheunitwilloperate.Theadjustmentshouldbemadewhenthe

ambientlightisatthelevelwherenoarticiallightisneeded.Follow

thesestepstomakeamoreaccurateadjustmentofthelightcontrol.

ThisfeaturewillnotworkinManual-Onmode.

 A. WiththelightsON,rotatetheTimeControlfullyCCWtotheset

theTime-Outtothethirty(30)secondtestmode(refer to Control

Panel Diagram).

 B. RotatetheLightControlfullyCCW.

 C. ManuallyturnOFFthelights.

 D. RotatetheLightControlclockwise(CW)SLOWLY,untilthelights

turnON.Thisisthesettingforthecurrentleveloflightintheroom.

Adjustthelightcontrolback(CCW)alittlesothelightswillnotturn

onwiththecurrentroomlightinglevel.Leavetheroomandwait

forthe30-secondtimeoutand30-secondvacancyconrmation

toexpire.Performawalkthroughtoseeifthelightsturnonwith

thenewambientlightleveladjustment.Repeatthisadjustmentas

neededtokeepthelightsfromturningonunderconditionswhen

enoughlightispresent.

 NOTE:WhenthelightcontrolisinthefullyCCWpositionthelights

willneverautomaticallyturnON.ThisistheManual-Onmode,

wherethelightsneedtobemanuallyturnedONbythepush-

button,andwillturnOFFwiththeabsenceofmotion.

  IfthelightcontrolisinthefullyCWposition,thelightswillturnON

whenevermotionisdetected,eveninfulldaylight.

  IntermediatesettingswillcausethelightstoturnONonlywhenthe

ambientlightisbelowthelevelselectedbythelightcontrol.

 NOTE:Theambientlightinaroomwillchangewiththetimeofday

andtheseasonoftheyear.

5. Time-Out Settings:

A. AdjusttheTimedial.TheSensorAmberLEDwillashtwiceeach

timetheTimedialispointedatanewTime-Outvalue.TheTime-

Outvaluesfornon-adaptingmodeare:

NOTE:Toreturntoadaptingmode,rotatetheTimedialtofullCW

position(Asetting).BesuretheTimedialisrotateduntilanAmber

LEDashisissuedtobesureanewsettingwasselected.

(/)SlashMark

30secondxedtime-outforperformingawalktest

10minutesxedtime-out

20minutesxedtime-out

30minutesxedtime-out

AutoAdapting

Value of TimeFace Marking

SETTINGS

OPERATION

LIMITED 5 YEAR WARRANTY AND EXCLUSIONS

LevitonwarrantstotheoriginalconsumerpurchaserandnotforthebenetofanyoneelsethatthisproductatthetimeofitssalebyLevitonisfreeofdefectsinmaterialsandworkmanshipundernormalandproperuseforveyearsfromthepurchasedate.Leviton’sonlyobligationistocorrectsuchdefectsbyrepairorreplacement,atitsoption,ifwithinsuchveyearperiodtheproductisreturnedprepaid,

withproofofpurchasedate,andadescriptionoftheproblemtoLeviton Manufacturing Co., Inc., Att: Quality Assurance Department, 59-25 Little Neck Parkway, Little Neck, New York 11362-2591.Thiswarrantyexcludesandthereisdisclaimedliabilityforlaborforremovalofthisproductorreinstallation.Thiswarrantyisvoidifthisproductisinstalledimproperlyorinanimproperenvironment,

overloaded,misused,opened,abused,oralteredinanymanner,orisnotusedundernormaloperatingconditionsornotinaccordancewithanylabelsorinstructions.There are no other or implied warranties of any kind, including merchantability and ﬁtness for a particular purpose,butifanyimpliedwarrantyisrequiredbytheapplicablejurisdiction,thedurationofanysuchimpliedwarranty,

includingmerchantabilityandtnessforaparticularpurpose,islimitedtoveyears.Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or proﬁts or delay or failure to perform this warranty obligation.Theremediesprovidedhereinaretheexclusiveremediesunderthiswarranty,

whetherbasedoncontract,tortorotherwise.

1. IfthereisnoresponsefromtheunitandtheLEDneverblinksor

thepushbuttondoesnotactivatethelights1-1/2minutesafter

powerisapplied,thenuninstalldeviceandverifywiring(Step 4).

2. IfthelightsconstantlystayON,evenwhentheroomisunoccupied:

 A.ChecktheTimesetting.Seehowthistimecomparestohow

longthelightsstayON.

 B.TryloweringthePIRRangeControl.Rotatetheknob

counterclockwiseabout30°.

 C.Iftheproblempersists,tryreducingagain.

 NOTE:DonotreducesomuchthattheSensorUnitcannotsee

normaloccupancy.

 D.TryloweringtheUltrasonicSensitivity.

 E.BesuretousetheBlinderstoblockanyunwantedhallway

trafc.

 F. Checkforreectedheat/motionastheSensorUnitmaybe

seeingmotionthroughawindow.

 G.CheckforadjacentHVACand/orheaterducts.

TROUBLESHOOTING

Lens

Blinders

Control panel

cover

Push button

LED window

US sensor ports

Thisequipmenthasbeentestedandfoundtocomplywiththelimits

foraClassAdigitaldevice,pursuanttopart15oftheFCCRules.

Theselimitsaredesignedtoprovidereasonableprotectionagainst

harmfulinterferencewhentheequipmentisoperatedinacommercial

environment.Thisequipmentgenerates,usesandcanradiateradio

frequencyenergyand,ifnotinstalledandusedinaccordancewith

theinstructionmanual,maycauseharmfulinterferencetoradio

communications.Operationofthisequipmentinaresidentialarea

islikelytocauseharmfulinterferenceinwhichcasetheuserwillbe

requiredtocorrecttheinterferenceattheirownexpense.

FCC COMPLIANCE STATEMENT

• Fortechnicalassistancecontactusat1-800-824-3005

• Visitourwebsiteatwww.leviton.com

PRODUCT INFORMATION

• Securedevicebyrmlytighteningmountingscrews.

• InstallDecora

stylewallplate(soldseparately).

Small Motion=DualTechnologycoverage.Thisalsorepresentsthe

maximumultrasonicrangecoverage.

Wall surface

Device mounting screw

(2 places)

Wallplate

mounting

screw

(2 places)

20 ft (6.1 m)

small motion

30 ft (9.1 m)

20 ft (6.1 m)

small motion

40 ft

(12.2 m)

Field - of - View (Horizontal)

40 ft.

(12.2 m)

4 ft.

(1.2 m)

Sensor

Side (Vertical) Field - of - View

DI-0XX-OSSMT-00A

Control Panel Diagram

US Sensitivity and PIR Disable

3 amber flashes High ultrasonic sensitivity, PIR enabled

2 amber flashes Medium ultrasonic sensitivity, PIR enabled

1 amber flash Low ultrasonic sensitivity, PIR enabled

3 green flashes High ultrasonic sensitivity, PIR disabled

2 green flashes Medium ultrasonic sensitivity, PIR disabled

1 green flash Low ultrasonic sensitivity, PIR disabled

NOTE:Theprogramtimesoutin30secondsfromthelastbutton

press.ThefactorysettingfortheUSsensitivityisHIGHwithPIRand

Ultrasonictechnologiesenabled.

7. ReplacetheControlPanelCoverandDecora

wallplate.

6. Ifdesired,adjusttheblinderstoblockanyunwantedmotion.

Leviton OSSMT-GDW Operating instructions

Brand: Leviton

Model: OSSMT-GDW

Type: Operating instructions

This manual is also suitable for

Download PDF

report

Leviton OSSMT-GDW Operating instructions

This manual is also suitable for

Leviton OSSMT-GDW Operating instructions

Related papers

Other documents