TECHNICAL QUICK GUIDE
Leviton Mfg. Co., Inc. Lighting & Energy Solutions
20497 SW Teton Avenue, Tualatin, OR 97062 1-800-736-6682 Tech Line: 1-800-959-6004 Fax: 503-404-5594 www.leviton.com/les
© 2011 Leviton Manufacturing Co., Inc. All rights reserved. Subject to change without notice.
Occupancy Sensor Automation
Occupancy Sensor Configuration
Reference Guide for Optimal Sensor Settings
OPTIMAL CONFIGURATION FOR AN
OCCUPANCY SENSOR
•
Location/Rotation of Sensor
• Passive Infrared (PIR is a line of sight
beam that reacts to heat motion across
a field of view.
•
Stand or sit at the entry point
spots in the room (can you see
the sensor lens?).
•
Ultrasonic (U/S) is a reflective wave
form that reacts to room disturbances
in return view form.
•
Stand or sit in the most used
spot in the room (can the signals
reflect your movement?).
•
Angle of Sensor
•
Sensor range is optimally designed at
90 . Any variance to the angle will result in
less range.
Mounting
Base
Base Cover
4.67 inch/118.62mm
4.23 inch/107.44 mm
6.43 inch/163.32mm
Sensor
WHILE CONFIGURING AN OCCUPANCY
SENSOR, REMEMBER
THAT IF YOU CANNOT SEE IT,
IT CANNOT SEE YOU.
ADJUST TO ACCOMODATE THE AREAS
THAT ARE MOST LIKELY
TO BE USED, IF NECESSARY.
58
31
16
11.5
31
58
8
SIDE VIEW
TOP VIEW
OSW12-M0W
Field of View (in feet)
Minor Motion, Ultrasonic
Major Motion, Ultrasonic
68
Minor Motion, IR
Major Motion, IR
0 3 8 15
23
32
31
0
0
11.5
16
PREFERRED ANGLE = MAX RANGE
(SPECIFIED FIELD OF VIEW)
Minor Motion, IR: Typing, stationery sitting or
standing with few gestures or movements, read-
ing, writing
Major Motion, IR: Walking, running, dancing,
sitting or standing with constant gestures or
movements
Minor Motion, U/V: Typing, stationery sitting or
standing with few gestures or movements, read-
ing, writing
Major Motion, U/V: Walking, running, danc-
ing, sitting or standing with constant gestures or
movements
90 Degree Angle (optimal setup)
Leviton Mfg. Co., Inc. Lighting & Energy Solutions
20497 SW Teton Avenue, Portland, OR 97062 1-800-736-6682 Tech Line: 1-800-959-6004 Fax: 503-404-5594 www.leviton.com/les
© 2011 Leviton Manufacturing Co., Inc. All rights reserved. Subject to change without notice.
Occupancy Sensor Configuration
COMMON CUSTOMER CONCERNS
1. Sensor not turning the lights on when I walk in the room
a. Auto-ON mode + correct configuration = lights will turn ON within two steps of entry.
b. Adjust location/rotation or angle of the sensor to better cover the entry points.
c. If (b.) has not corrected, then increase PIR (red dial) slightly until desired reaction at entry.
2. Lights are turning off on me = false-OFF
a. Adjust location/rotation or angle of the sensor to better cover the user’s location.
b. If (a.) has not corrected, then increase time delay (black dial) = improves probability of sensing motion.
c. If (a.) and (b.) have not corrected, then increase U/S (green dial) slightly until desired reaction at user
location.
3. Lights are on when no one is in the room = false-on
a. Adjust location/rotation or angle of the sensor to block or remove the offending object (such that
the sensor cannot detect this unwanted motion: minimum 6 feet from air vents and 4 feet from fixtures).
b. PIR will turn the lights ON with any heated motion (oscillating fans, moving parts, pets, etc.).
i. If (a.) has not corrected, then decrease PIR (red dial) slightly until lights turn off (no longer
detecting unwanted motion).
c. U/S will keep the lights ON with any room disturbance (high air flow, flag or cloth blowing, fans, etc.).
i. If (a.) and (b.) have not corrected, then reduce U/S (green dial) slightly until lights turn OFF after
appropriate time setting.
4. Lights turn on in a room when someone walks past in the hallway
a. Auto-ON mode + correct configuration = lights will turn ON within two steps of entry.
b. Adjust location/rotation or angle of the sensor so that you cannot see it from the hallway.
c. If (b). has not corrected, then decrease PIR (red dial) slightly until hallway motion does not activate.
SWITCH FUNCTIONS
Bank A OFF ON
Single/Multi-Tech Mode Multi-Tech Single Tech
PIR/Ultrasonic Mode PIR Ultrasonic
Manual Mode A uto Adapting Enabled A uto Adapting Disabled
Walk-Through Disable Walk-Through Enable Walk-Through Disable
Bank B
Override to ON Auto Mode Lights Forced ON
Override to OFF Auto Mode Lights Forced OFF
Test Mode OFF ON OFF = Enter/Exit Test Mode
LEDs Disable LEDs Enabled LEDs Disable
TABLE 2: SWITCH SETTINGS
SWITCH SETTINGS
SWITCH
A1
A2
*
A3
A4
B1
B2
B3
B4
TABLE 1: ADJUSTMENT KNOB SETTINGS
Knob
Color
Function
Sets the ultrasonic range
Sets the infrared range
Delayed- O Time
Ambient Light Override
(Gray wire only)
Knob Setting
Range setting
Full CCW = min. (OFF)
Full CW = max.
Range setting
Full CCW = min. (OFF)
Full CW = max.
Full CCW = min. (30 sec.)
Full CW = max. (30 min.)
Factory Default
Setting
75%
50%
100%
Full CCW – Lights stay OFF
Full CW – Lights always turn ON
(NO ambient light override)
Range – 100-3000 LUX
50%
(10 min)
Blue
Black
Red
Green
Symbol
.
SWITCH FUNCTIONS
Bank A OFF ON
Single/Multi-Tech Mode Multi-Tech Single Tech
PIR/Ultrasonic Mode PIR Ultrasonic
Manual Mode A uto Adapting Enabled A uto Adapting Disabled
Walk-Through Disable Walk-Through Enable Walk-Through Disable
Bank B
Override to ON Auto Mode Lights Forced ON
Override to OFF Auto Mode Lights Forced OFF
Test Mode OFF ON OFF = Enter/Exit Test Mode
LEDs Disable LEDs Enabled LEDs Disable
TABLE 2: SWITCH SETTINGS
SWITCH SETTINGS
SWITCH
A1
A2
*
A3
A4
B1
B2
B3
B4
TABLE 1: ADJUSTMENT KNOB SETTINGS
Knob
Color
Function
Sets the ultrasonic range
Sets the infrared range
Delayed- O Time
Ambient Light Override
(Gray wire only)
Knob Setting
Range setting
Full CCW = min. (OFF)
Full CW = max.
Range setting
Full CCW = min. (OFF)
Full CW = max.
Full CCW = min. (30 sec.)
Full CW = max. (30 min.)
Factory Default
Setting
75%
50%
100%
Full CCW – Lights stay OFF
Full CW – Lights always turn ON
(NO ambient light override)
Range – 100-3000 LUX
50%
(10 min)
Blue
Black
Red
Green
Symbol
.
SWITCH FUNCTIONS
Bank A OFF ON
Single/Multi-Tech Mode Multi-Tech Single Tech
PIR/Ultrasonic Mode PIR Ultrasonic
Manual Mode A uto Adapting Enabled A uto Adapting Disabled
Walk-Through Disable Walk-Through Enable Walk-Through Disable
Bank B
Override to ON Auto Mode Lights Forced ON
Override to OFF Auto Mode Lights Forced OFF
Test Mode OFF ON OFF = Enter/Exit Test Mode
LEDs Disable LEDs Enabled LEDs Disable
TABLE 2: SWITCH SETTINGS
SWITCH SETTINGS
SWITCH
A1
A2
*
A3
A4
B1
B2
B3
B4
TABLE 1: ADJUSTMENT KNOB SETTINGS
Knob
Color
Function
Sets the ultrasonic range
Sets the infrared range
Delayed- O Time
Ambient Light Override
(Gray wire only)
Knob Setting
Range setting
Full CCW = min. (OFF)
Full CW = max.
Range setting
Full CCW = min. (OFF)
Full CW = max.
Full CCW = min. (30 sec.)
Full CW = max. (30 min.)
Factory Default
Setting
75%
50%
100%
Full CCW – Lights stay OFF
Full CW – Lights always turn ON
(NO ambient light override)
Range – 100-3000 LUX
50%
(10 min)
Blue
Black
Red
Green
Symbol
.
SWITCH FUNCTIONS
Bank A OFF ON
Single/Multi-Tech Mode Multi-Tech Single Tech
PIR/Ultrasonic Mode PIR Ultrasonic
Manual Mode A uto Adapting Enabled A uto Adapting Disabled
Walk-Through Disable Walk-Through Enable Walk-Through Disable
Bank B
Override to ON Auto Mode Lights Forced ON
Override to OFF Auto Mode Lights Forced OFF
Test Mode OFF ON OFF = Enter/Exit Test Mode
LEDs Disable LEDs Enabled LEDs Disable
TABLE 2: SWITCH SETTINGS
SWITCH SETTINGS
SWITCH
A1
A2
*
A3
A4
B1
B2
B3
B4
TABLE 1: ADJUSTMENT KNOB SETTINGS
Knob
Color
Function
Sets the ultrasonic range
Sets the infrared range
Delayed- O Time
Ambient Light Override
(Gray wire only)
Knob Setting
Range setting
Full CCW = min. (OFF)
Full CW = max.
Range setting
Full CCW = min. (OFF)
Full CW = max.
Full CCW = min. (30 sec.)
Full CW = max. (30 min.)
Factory Default
Setting
75%
50%
100%
Full CCW – Lights stay OFF
Full CW – Lights always turn ON
(NO ambient light override)
Range – 100-3000 LUX
50%
(10 min)
Blue
Black
Red
Green
Symbol
.
SWITCH FUNCTIONS
Bank A OFF ON
Single/Multi-Tech Mode Multi-Tech Single Tech
PIR/Ultrasonic Mode PIR Ultrasonic
Manual Mode A uto Adapting Enabled A uto Adapting Disabled
Walk-Through Disable Walk-Through Enable Walk-Through Disable
Bank B
Override to ON Auto Mode Lights Forced ON
Override to OFF Auto Mode Lights Forced OFF
Test Mode OFF ON OFF = Enter/Exit Test Mode
LEDs Disable LEDs Enabled LEDs Disable
TABLE 2: SWITCH SETTINGS
SWITCH SETTINGS
SWITCH
A1
A2
*
A3
A4
B1
B2
B3
B4
TABLE 1: ADJUSTMENT KNOB SETTINGS
Knob
Color
Function
Sets the ultrasonic range
Sets the infrared range
Delayed- O Time
Ambient Light Override
(Gray wire only)
Knob Setting
Range setting
Full CCW = min. (OFF)
Full CW = max.
Range setting
Full CCW = min. (OFF)
Full CW = max.
Full CCW = min. (30 sec.)
Full CW = max. (30 min.)
Factory Default
Setting
75%
50%
100%
Full CCW – Lights stay OFF
Full CW – Lights always turn ON
(NO ambient light override)
Range – 100-3000 LUX
50%
(10 min)
Blue
Black
Red
Green
Symbol
.
SWITCH FUNCTIONS
Bank A OFF ON
Single/Multi-Tech Mode Multi-Tech Single Tech
PIR/Ultrasonic Mode PIR Ultrasonic
Manual Mode A uto Adapting Enabled A uto Adapting Disabled
Walk-Through Disable Walk-Through Enable Walk-Through Disable
Bank B
Override to ON Auto Mode Lights Forced ON
Override to OFF Auto Mode Lights Forced OFF
Test Mode OFF ON OFF = Enter/Exit Test Mode
LEDs Disable LEDs Enabled LEDs Disable
TABLE 2: SWITCH SETTINGS
SWITCH SETTINGS
SWITCH
A1
A2
*
A3
A4
B1
B2
B3
B4
TABLE 1: ADJUSTMENT KNOB SETTINGS
Knob
Color
Function
Sets the ultrasonic range
Sets the infrared range
Delayed- O Time
Ambient Light Override
(Gray wire only)
Knob Setting
Range setting
Full CCW = min. (OFF)
Full CW = max.
Range setting
Full CCW = min. (OFF)
Full CW = max.
Full CCW = min. (30 sec.)
Full CW = max. (30 min.)
Factory Default
Setting
75%
50%
100%
Full CCW – Lights stay OFF
Full CW – Lights always turn ON
(NO ambient light override)
Range – 100-3000 LUX
50%
(10 min)
Blue
Black
Red
Green
Symbol
.
ADVANCED OPERATIONS
1. Maximize energy savings with Auto Adapting Technology
(factory default settings).
DIP SWITCH SETTINGS
SWITCH FUNCTIONSSWITCH SWITCH SETTINGS
BANK A OFF ON
A1 N/A Multi-Tech Single Tech
A2 N/A PIR Ultrasonic
A3 Manual Mode Auto Adapting Enabled Auto Adapting Disabled
A4
Walk-Thru Disable
Walk-Thru Enabled Walk-Thru Enabled
BANK B
B1 Override to On Auto Mode Lights forced ON
B2 Override to Off Auto Mode Lights forced OFF
B3 Test Mode OFF’ON’OFF Enter/Exit Test Mode
B4 LED Disable LEDs Enabled LEDs Disabled
2. For fixed (stable) settings, the Auto Adapting
and Walk-Thru feature must be disabled.
• Not desirable for maximizing energy
savings.
• Desirable in educational environments
due to vacation periods.
• Desirable if end user expectations are
that all lights will operate ON/OFF the
same way all the time.
• Desirable if troubleshooting, this will
eliminate strange time delays and U/S
sensitivity.
TO DISABLE ADVANCED FEATURES
a. To disable Auto Adapting, flip the A3
dip switch to the rght (ON Position).
b. To disable Walk-Thru, flip the A4 dip
switch to the right (ON Position).
SWITCH FUNCTIONS
Bank A OFF ON
Single/Multi-Tech Mode Multi-Tech Single Tech
PIR/Ultrasonic Mode PIR Ultrasonic
Manual Mode A uto Adapting Enabled A uto Adapting Disabled
Walk-Through Disable Walk-Through Enable Walk-Through Disable
Bank B
Override to ON Auto Mode Lights Forced ON
Override to OFF Auto Mode Lights Forced OFF
Test Mode OFF ON OFF = Enter/Exit Test Mode
LEDs Disable LEDs Enabled LEDs Disable
TABLE 2: SWITCH SETTINGS
SWITCH SETTINGS
SWITCH
A1
A2
*
A3
A4
B1
B2
B3
B4
TABLE 1: ADJUSTMENT KNOB SETTINGS
Knob
Color
Function
Sets the ultrasonic range
Sets the infrared range
Delayed- O Time
Ambient Light Override
(Gray wire only)
Knob Setting
Range setting
Full CCW = min. (OFF)
Full CW = max.
Range setting
Full CCW = min. (OFF)
Full CW = max.
Full CCW = min. (30 sec.)
Full CW = max. (30 min.)
Factory Default
Setting
75%
50%
100%
Full CCW – Lights stay OFF
Full CW – Lights always turn ON
(NO ambient light override)
Range – 100-3000 LUX
50%
(10 min)
Blue
Black
Red
Green
Symbol
.
SWITCH FUNCTIONS
Bank A OFF ON
Single/Multi-Tech Mode Multi-Tech Single Tech
PIR/Ultrasonic Mode PIR Ultrasonic
Manual Mode A uto Adapting Enabled A uto Adapting Disabled
Walk-Through Disable Walk-Through Enable Walk-Through Disable
Bank B
Override to ON Auto Mode Lights Forced ON
Override to OFF Auto Mode Lights Forced OFF
Test Mode OFF ON OFF = Enter/Exit Test Mode
LEDs Disable LEDs Enabled LEDs Disable
TABLE 2: SWITCH SETTINGS
SWITCH SETTINGS
SWITCH
A1
A2
*
A3
A4
B1
B2
B3
B4
TABLE 1: ADJUSTMENT KNOB SETTINGS
Knob
Color
Function
Sets the ultrasonic range
Sets the infrared range
Delayed- O Time
Ambient Light Override
(Gray wire only)
Knob Setting
Range setting
Full CCW = min. (OFF)
Full CW = max.
Range setting
Full CCW = min. (OFF)
Full CW = max.
Full CCW = min. (30 sec.)
Full CW = max. (30 min.)
Factory Default
Setting
75%
50%
100%
Full CCW – Lights stay OFF
Full CW – Lights always turn ON
(NO ambient light override)
Range – 100-3000 LUX
50%
(10 min)
Blue
Black
Red
Green
Symbol
.
SWITCH FUNCTIONS
Bank A OFF ON
Single/Multi-Tech Mode Multi-Tech Single Tech
PIR/Ultrasonic Mode PIR Ultrasonic
Manual Mode A uto Adapting Enabled A uto Adapting Disabled
Walk-Through Disable Walk-Through Enable Walk-Through Disable
Bank B
Override to ON Auto Mode Lights Forced ON
Override to OFF Auto Mode Lights Forced OFF
Test Mode OFF ON OFF = Enter/Exit Test Mode
LEDs Disable LEDs Enabled LEDs Disable
TABLE 2: SWITCH SETTINGS
SWITCH SETTINGS
SWITCH
A1
A2
*
A3
A4
B1
B2
B3
B4
TABLE 1: ADJUSTMENT KNOB SETTINGS
Knob
Color
Function
Sets the ultrasonic range
Sets the infrared range
Delayed- O Time
Ambient Light Override
(Gray wire only)
Knob Setting
Range setting
Full CCW = min. (OFF)
Full CW = max.
Range setting
Full CCW = min. (OFF)
Full CW = max.
Full CCW = min. (30 sec.)
Full CW = max. (30 min.)
Factory Default
Setting
75%
50%
100%
Full CCW – Lights stay OFF
Full CW – Lights always turn ON
(NO ambient light override)
Range – 100-3000 LUX
50%
(10 min)
Blue
Black
Red
Green
Symbol
.
G-8629/H11-tb
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Leviton OSW12-M0W Installation guide
-
Leviton OSC10-M0W Operating instructions
-
Leviton ODC20-MDW Installation guide
-
-
-
-
-
Leviton OSSMT-GDT Operating instructions
-
-
Other documents
-
Haworth kp04-4441a Operating instructions
-
Crestron GLS-ODT-W-1200 User guide
-
Crestron electronic GLS-ODT-W-1200 User manual
-
Crestron electronic GLS-ODT-C-500. GLS-ODT-C-1000 User manual
-
-
Oriana 704677 Specification
-
Crestron electronic GLS-OIR-C-450/1500 User manual
-
Extron electronics OCS 100C User manual
-
Greengate ONW-D-1001-347-W Installation guide
-
Greengate NeoSwitch - 120/277/347V Dual Tech/Single Level Wall Switch Sensor (Ground Required) Installation guide
