2. Computers & electronics
  3. TVs & monitors
  4. Flat panel desk mounts
  5. Innovative
  6. STX-02-SLD-104

Innovative STX-02-SLD-104 User manual

  • Hello! I've reviewed the installation instructions for the Innovative Ergonomic Solutions Monitor Mount STX-02-SLD. This document provides detailed steps for both desk clamp and thru-desk mounting options, ensuring correct assembly using various tools and components. I'm ready to answer any questions you might have about installing this dual monitor mount.
  • What desk thickness is supported by the desk clamp configuration?
    What is included with the optional thru-desk kit?
    What tools are needed for the installation?
STA X X
Installation Instructions
Innovative Ergonomic Solutions
800 524 2744
customerservice@team-ies.com
team-ies.com
HAT Collective
408 437 8770
cs@hatcollective.com
hatcollective.com
™
© 2021 Innovative Ergonomic Solutions REV A
STX-02-SLD
PAGE 1 OF 13
A Top Down Mount 1x
8524
B Dimpled Pole 1x
110607-14
C Stackable Mount 1x
413054
D Pole Collar 1x
113332
E Pole Clip 1x
113449
F Bushing Adapter 2x
112945
G Rotation Stop for Extension Arms 2x
113703
H 10-32 x 5/8" Phillips Pan Head Screw 2x
702200
I Quick Connect VESA Plate 2x
114808
J M4 x 12mm Phillips Pan Head Screw 8x
701153
K 9-inch Beam Assembly 2x
416088
L Dog Washer 2x
105189
M 10-32 x 3/8" FPhMS w/Lock Patch 2x
705198
N Pole Cap 1x
105195
O Cable Clip 1x
104533
P 1/8" Allen Wrench 1x
701312
Q 3/32" Allen Wrench 1x
700146
R 7/32" Allen Wrench 1x
701127
S 4mm Allen Wrench 1x
709877
T* M8 x 95mm SCHS 1x
716061
U* Spacer 1x
701544
V* Lock Nut 1x
710015
* Included with optional thru-desk kit only, model # 8524-TM-CK (sold separately).
PARTS LIST
PAGE 2 OF 13
R
A
OR
Desk thickness
up to 1.5" (3.8 cm)
Desk thickness
up to 1.5" (3.8 cm)
iIf the monitor arm or pole does not easily fit into the
mount, remove the bushing from the mount and place
it on the monitor arm or pole and press firmly back
into the mount.
OR
1 2
2a 2b 2c
7/32"
DESK CLAMP CONFIGURATION
PAGE 3 OF 13
3 4
THRU-DESK CONFIGURATION*
* Thru-desk kit required, model # 8524-TM-CK (sold separately).
R
T
U
V
7/32"
Desk thickness
up to 1.5" (3.8 cm)
PAGE 4 OF 13
5
Q
B
C
D
i
IMP OR TAN T:
When inserting
pole into mount,
the dimples
should be aligned
perpendicular to
the rear edge of
mounting surface.
Dimples
3/32"
PAGE 5 OF 13
6
E
PAGE 6 OF 13
F
G
7
iIMP OR TAN T: Install part
(G) in the orientation as
shown. When washer,
part (G), is installed
correctly, the lower
extension arms will not
rotate past the back of
the mount.
H
G
F
PAGE 7 OF 13
2x
I
K
L
M
8
PAGE 8 OF 13
2x
K
L
M
9
PAGE 9 OF 13
10
J
I
2x
PAGE 10 OF 13
11
2x
2x
PAGE 11 OF 13
12
4 mm
S
2x
PAGE 12 OF 13
O
N
13
PAGE 13 OF 13
/