Page is loading ...
© 2021 Innovative Ergonomic Solutions REV A
Innovative Ergonomic Solutions
800 524 2744
customerservice@team-ies.com
team-ies.com
HAT Collective
408 437 8770
cs@hatcollective.com
hatcollective.com
STA X X
Installation Instructions
STX-3S-SLD-XXX
™
PAGE 1 OF 17
A Top Down Mount 1x
8524
B Dimpled Pole 1x
110607-20
C Stackable Mount 3x
413054
D Pole Collar 1x
113332
E Pole Clip 1x
113449
F 9-inch Beam Assembly 2x
416088
G Dog Washer for Articulating Arms 2x
113704
H Rotation Stop for Articulating Arms 2 x
113705
I M6 x 1mm Phillips Pan Head Screw 2x
105304
J Quick Connect VESA Plate 3x
114808
K M4 x 12mm Phillips Pan Head Screw 12x
701153
L Monitor Tilter 1x
8500 Tilter
M Bushing Adapter 1x
112945
N Dog Washer 3x
105189
O 10-32 x 3/8" FPhMS w/Lock Patch 3x
705198
P Pole Cap 1x
105195
Q Cable Clip 1x
104533
R Cable Cap 2x
114810
S Forearm Cable Cap 2x
115584
T 1/8" Allen Wrench 1x
701312
U 3/32" Allen Wrench 1x
700146
V 7/32" Allen Wrench 1x
701127
W 4mm Allen Wrench 1x
709877
X* M8 x 95mm SCHS 1x
716061
Y* Spacer 1x
701544
Z* Lock Nut 1x
710015
Parts List
* Included with optional thru-desk kit only, model # 8524-TM-CK (sold separately).
PAGE 2 OF 17
V
A
Desk thickness
up to 1.5" (3.8 cm)
Desk thickness
up to 1.5" (3.8 cm)
iIf the monitor arm or pole does not easily fit into the
mount, remove the bushing from the mount and place
it on the monitor arm or pole and press firmly back
into the mount.
OR
1 2
2a 2b 2c
7/32"
DESK CLAMP CONFIGURATION
OR
PAGE 3 OF 17
3 4
THRU-DESK CONFIGURATION*
V
X
Y
Z
7/32"
Desk thickness
up to 1.5" (3.8 cm)
* Thru-desk kit required, model # 8524-TM-CK (sold separately).
PAGE 4 OF 17
5
B
C
D
i
IMP ORTANT:
When inserting
pole into mount,
the dimples
should be aligned
perpendicular to
the rear edge of
mounting surface.
Dimples
U
3/32"
PAGE 5 OF 17
6
E
PAGE 6 OF 17
7
G
G
H
H
iIMP ORTANT:
Install part (H) in the
orientation as shown to
the left. When washer,
part (H), is installed
correctly, the arms will
not rotate past the back
of the mount.
G
I
PAGE 7 OF 17
8
2x
J
F
N
O
PAGE 8 OF 17
2x
9
F
N
O
PAGE 9 OF 17
10
K
J
3x
PAGE 10 OF 17
11
L
1x
PAGE 11 OF 17
12
1x
N
MO
M
PAGE 12 OF 17
13
2x
PAGE 13 OF 17
14
7/32"
2x
V
i
In some instances, an additional
counterbalance adjustment may
be needed to allow the arm’s
instant height adjustment function
to work properly.
If your arm is not staying in position
after performing step 14, tighten
the adjustment screw with a
1/8" Allen wrench.
T
1/8"
Optional Adjustment
PAGE 14 OF 17
15
4 mm
W
T
1/8"
2x
1x
PAGE 15 OF 17
16
2x
PAGE 16 OF 17
17
2x
Q
T
2x
S
R
PAGE 17 OF 17
/
