2. Innovative Design Works
  3. PTS-04-LANE
PTS-04-LANE

Innovative Design Works PTS-04-LANE User manual

  • Hello, I've reviewed the Installation Instructions for the PTS-04-LANE payment terminal mount. This document details how to install the mount and covers important aspects such as cable routing, rotation configuration, and tilt adjustment. I am ready to answer any questions you might have about these installation instructions or the device described in them.
  • How do I adjust the rotation of the mount?
    How do I release top of the mount?
    What is the adapter key used for?
© 2021 Innovative Ergonomic Solutions REV B
PTS-04-LANE
Installation Instructions
Innovative Ergonomic Solutions
800 524 2744
customerservice@team-ies.com
team-ies.com
PAGE 1 OF 8
A T15 L-Key 1x
714904
B T20 L-Key 1x
714997
C T25 L-Key 1x
714899
D Lane Adapter Screw 2x
714305
E Lane Adapter Key 2x
114307
PTS-04-LANE
Parts List
PAGE 2 OF 8
Optional grommet
hole for routing
cables below
mounting surface.
Mounting hardware
not included.
Use appropriate
hardware for your
mounting surface.
For above surface
cable routing, route
the cable prior to
installing the mount.
i
IM PORTANT:
Determine cable routing prior to
installing mount. This will ensure
the mount is installed in the correct
orientation for your installation.
Above Surface Cable Routing
Locate the mount cable exit and plan
your installation accordingly.
Below Surface Cable Routing
Cables may pass through the mount
(requires grommet hole).
Cable
Entry
Cable
Entry
Cable
Exit
Cable
Exit
1
PAGE 3 OF 8
iROTATION STOP
CONFIGURATION
EXAMPLES
OR
Rotation Stop Ribs
Place this area over
the rotation stop
screw or pin to
prevent the mount
from rotating.
Rotation
Stop Screw
iNO ROTATION
CONFIGURATION
EXAMPLES
Rotation
Stop Screw
Rotation
Stop Screw
2
Rotation
Stop Pin
T20 T20
Placement of the two rotation stop screws in
the outer ring determine the amount of payment
terminal rotation. You can remove the screws from
their original location and place them in any of the
holes in the outer ring to allow for the amount of
desired rotation.
There are rotation stop ribs underneath the
top portion of the mount that can be placed
directly over the rotation stop screw or pin.
This positioning will prevent the payment terminal
from rotating. Determine the proper
rotation stop screw location for your installation.
ROTATION NO ROTATION
PAGE 4 OF 8
iHOW TO RELEASE MOUNT
Locate the release tab inside the mount. Using
a screwdriver, or similar tool, pull back on the
tab. With the tab pulled back, lift up on the upper
portion of the mount to release.
Release Tab
When placing the top of the mount onto
the base, ensure the rotation stop ribs fall
in between the rotation stops that were
set in place in Step 2.
Or in a no rotation configuration, the ribs
must be placed over top the rotation stop
screw or pin.
3
PAGE 5 OF 8
4a
4b
T25
T25
PAGE 6 OF 8
5a Push the adapter key down.
5b With the key pushed down,
pull the key back.
5c With the key pushed back,
slide payment terminal onto mount.
Once the payment terminal is successfully
attached to the mount, the key can be
returned to its original position or removed to
lock the payment terminal on the stand.
iADAPTER KEY
The Lane adapter key (item E), needs to be
inserted in the mount in order to attach and
detach the payment terminal.
5b
5a
5c
PAGE 7 OF 8
OR
iADJUSTMENT FEATURE
To adjust the tilt friction, remove the hex nut covers
and tighten or loosen the 13mm hex nut while securing
the pivot screw on the inside of the mount with a 14mm
wrench. Adjust both sides as needed.
6
13mm
14mm
PAGE 8 OF 8
/