Table of contents
Measuring cycles
6 Programming Manual, 02/2011, 6FC5398-4BP40-0BA0
2.3 Measure workpiece (milling) ....................................................................................................... 83
2.3.1 Calibrate probe - length (CYCLE976)......................................................................................... 83
2.3.2 Calibrate probe - radius in ring (CYCLE976) .............................................................................. 86
2.3.3 Calibrate probe - radius on edge (CYCLE976)........................................................................... 90
2.3.4 Calibrate probe - calibrate on ball (CYCLE976).......................................................................... 93
2.3.5 Edge distance - set edge (CYCLE978)....................................................................................... 96
2.3.6 Edge distance - align edge (CYCLE998).................................................................................. 100
2.3.7 Edge distance - groove (CYCLE977)........................................................................................ 106
2.3.8 Edge distance - rib (CYCLE977)............................................................................................... 110
2.3.9 Corner - right-angled corner (CYCLE961) ................................................................................ 114
2.3.10 Corner - any corner (CYCLE961) ............................................................................................. 118
2.3.11 Hole - rectangular pocket (CYCLE977) .................................................................................... 122
2.3.12 Hole - 1 hole (CYCLE977) ........................................................................................................ 126
2.3.13 Hole - inner circle segment (CYCLE979).................................................................................. 130
2.3.14 Spigot - rectangular spigot (CYCLE977)................................................................................... 134
2.3.15 Spigot - 1 circular spigot (CYCLE977)...................................................................................... 138
2.3.16 Spigot - outer circle segment (CYCLE979)............................................................................... 142
2.3.17 3D - align plane (CYCLE998) ................................................................................................... 146
2.3.18 3D - sphere (CYCLE997).......................................................................................................... 150
2.3.19 3D - 3 spheres (CYCLE997) ..................................................................................................... 154
2.3.20 3D - kinematics (CYCLE996).................................................................................................... 159
2.4 Measure tool (turning)............................................................................................................... 175
2.4.1 General information................................................................................................................... 175
2.4.2 Calibrate probe (CYCLE982) .................................................................................................... 178
2.4.3 Turning tool (CYCLE982).......................................................................................................... 182
2.4.4 Milling tool (CYCLE982)............................................................................................................ 186
2.4.5 Drill (CYCLE982)....................................................................................................................... 193
2.4.6 Measure tool with toolholder that can be orientated ................................................................. 198
2.5 Measure tool (milling)................................................................................................................ 200
2.5.1 General information................................................................................................................... 200
2.5.2 Calibrate probe (CYCLE971) .................................................................................................... 202
2.5.3 Measure tool (CYCLE971)........................................................................................................208
3 Parameter lists....................................................................................................................................... 215
3.1 Overview of measuring cycle parameters................................................................................. 215
3.1.1 CYCLE973 measuring cycle parameters.................................................................................. 215
3.1.2 CYCLE974 measuring cycle parameters.................................................................................. 218
3.1.3 CYCLE994 measuring cycle parameters.................................................................................. 221
3.1.4 CYCLE976 measuring cycle parameters.................................................................................. 224
3.1.5 CYCLE978 measuring cycle parameters.................................................................................. 226
3.1.6 CYCLE998 measuring cycle parameters.................................................................................. 229
3.1.7 CYCLE977 measuring cycle parameters.................................................................................. 232
3.1.8 CYCLE961 measuring cycle parameters.................................................................................. 235
3.1.9 CYCLE979 measuring cycle parameters.................................................................................. 238
3.1.10 CYCLE997 measuring cycle parameters.................................................................................. 241
3.1.11 CYCLE996 measuring cycle parameters.................................................................................. 244
3.1.12 CYCLE982 measuring cycle parameters.................................................................................. 247
3.1.13 CYCLE971 measuring cycle parameters.................................................................................. 250
3.2 Additional parameters ............................................................................................................... 253
3.3 Additional result parameters ..................................................................................................... 255