Backlit LCD Display
Stainless Steel Platform For easy clean up
Locking Mode
5 Years Warranty
SPECIFICATIONS
MODEL :
US-MINIBENCH
Maximum Capacity :
1000g
Minimum Capacity :
0.1g
Weighing Modes :
g, oz, gn,ct, ozt, dwt
Power :
2 x AAA
Overall Size :
3" x 4.25"
Platform Size :
2.7" x 2.7"
Colors :
Silver
Calibration Mass :
500g
Pcs count Per Inner Carton :
50pcs
Pcs Count per Case :
100pcs
US-MINIBENCH Use & Care Instructions
Thank you for purchasing a US Balance pocket scale.
We are confident that with normal use and proper treatment your scale will provide you with years of
reliable service. Please read all the operation instructions carefully before you use your new scale.
Display Messages:
LO — Low battery; please change the batteries in the scale.
OuEr — The load cell of the scale is being overloaded. You need to remove the excessive
weight from the scale immediately.
UnSt — The scale is placed on an unstable surface, please move the scale to a more stable
surface.
rCAL — the scale cannot return to zero, please recalibrate the scale.
CAL — This is the prompt for beginning the calibration process of your scale. You will see
this message when you press and hold the Cal button on your scale. Once this message appears,
you must release the button and follow the remaining steps for calibrating your scale.
PASS — you have successfully calibrated your scale, you are now able to use the scale.
FAIL — Calibration has failed, please make sure you have the scale on a stable surface and that
you are using the correct weight to calibrate the scale. Try to calibrate the scale following the
calibration instructions exactly.
US Balance Scale Instructions:
ON/OFF FUNCTION
Place your scale on a flat and stable surface away from any electronic equipment that may interfere
with the scale. Press and release the ON/OFF button, wait until the display shows “0.0” and the zero-
stable sign , you may now place the object you want to weigh on the platform. The scale can be
read when the lock sign is shown in the display.
TARE FUNCTION
Turn on the scale as described above, place the “tare item” on the platform, press the “TARE” button to
zero out the display, when “0.0” appears on the screen you may now place items on the scale to be
weighed. Once you are finished weighing, remove all objects from the scale, press the “TARE” again to
cancel the TARE FUNCTION.
RETURN TO ZERO
After weighing an item, if the display does not read “0.0” press the TARE button to return to “0.0” and
you are ready to weigh again.
CHANGE WEIGHING MODES
Press the “MODE” button to change weighing modes on your scale. This scale has 6 weighing modes: g,
oz, gn, ct, ozt, dwt.
CALIBRATION
With the scale turned on and placed on a stable surface, press and hold the COUNTING & CALIBRATION
button. The display will show “CAL”, press and release COUNTING & CALIBRATION button again and
“500.0” will flash in the display, immediately place a total of 500g weight on the scale. The scale will
reset itself and will give you a PASS message. Calibration is complete.
PARTS COUNTING FUNCTION
Place a small quantity of the item you want to count on the platform, (please note this should be a
quantity of 10, 25 or 5opcs previously counted out by hand.) After the display shows the weight of the
items, then press the “COUNTING&CALIBRATION” button, the display will automatically show 10, use
the COUNTING&CALIBRATION button to change your quantity selection until it is the same as the
quantity on the scale. The “PARTS” function will be set up automatically once you have chosen the
quantity and wait for several seconds. Remove the items and the display will show “O” you may now
count out items as long as their total weight does not exceed 1000g.
Once you are finished with the PARTS COUNTING FUNCTION, press the “MODE” again to cancel the
“PARTS” function.
OPERATING ENVIRONMENT
The optimum operating temperature for the scale is 50-86° F/l 0-30° C. Rough handling of the scale will
damage the internal sensor; so you must avoid actions such as shaking or dropping the scale. This is a
sensitive piece of electronic equipment and will be affected by things such as moisture, extreme
temperature changes, magnetic fields, careless handling and misuse.
AUTOMATIC SHUTOFF
The scale will automatically shut-off after 60 seconds of inactivity this is to help conserve the battery
power. We recommend good quality AAA batteries.
Tested to comply with FCC standards.
/
