Symantec NetBackup 5000 Replacement Manual

Brand: Symantec

Model: NetBackup 5000

Type: Replacement Manual

NetBackup 5000 Chassis Replacement v. 1.3

NBU 5000 Chassis Replacement Guide v. 1.3

Chassis replacement Guide

Impact on the System



Only professional maintenance personnel are allowed to remove the

middle or rear cover of the chassis to replace the parts in the system.



Before removing the middle or rear cover of the chassis to replace the

parts in the system, power off the NetBackup 5000 and disconnect the

NetBackup 5000 from the power sockets and external devices.



Powering off the NetBackup 5000 will affect the service running. Perform

this operation with caution!

Power off the NetBackup 5000 before replacing the chassis; otherwise, the services of the

NetBackup 5000 may be affected.

Prerequisite



The chassis for replacing is available



The chassis to be replaced is located.



Record the original IPMI IP address of the chassis to be replaced

Step 1 Connect the NetBackup 5000 cabinet to the KVM.

Step 2 Press the Power button on the rear of the cabinet to power on the

NetBackup 5000

Step 3 On the system self-check page, the IPMI IP address is displayed, as

shown in Figure 1-1.



In this section, the following procedures use the IPMI IP address: 192.168.0.10 as

an example.

NetBackup 5000 Chassis Replacement v. 1.3

NBU 5000 Chassis Replacement Guide v. 1.3

Figure 1-1 IPMI IP address displayed on the system self-check Page

Step 4 Record the IP Address, Subnet Mask and GateWay.



Before replacing the chassis, power off the NetBackup 5000 and

disconnect it from the power sockets and external devices.

Tools and Materials



Philips screwdriver



ESD-preventive gloves



ESD-preventive wrist strap



ESD-preventive clothes



ESD-preventive bag



Tag



PC client (Windows)



Switch



IPMITOOL software

Precaution



The NetBackup 5000 is supported by two power supplies. Cut off both of

the power supplies when powering off the NetBackup 5000.



Do not pry the CPU cooling fin during operation; otherwise the CPU and

the cooling fin will be damaged.

NetBackup 5000 Chassis Replacement v. 1.3

NBU 5000 Chassis Replacement Guide v. 1.3

Procedure

Step 1 Wear the ESD-preventive clothes, ESD-preventive wrist strap, and

ESD-preventive gloves. For details on how to wear the

ESD-preventive wrist strap, see Wearing the ESD-Preventive Wrist

Strap in Error! Reference source not found.“Error! Reference

source not found.”.

Step 2 Power off the NetBackup 5000 and disconnect the NetBackup 5000

from the power sockets and external devices.

Step 3 Smoothly pull the NetBackup 5000 out of the cabinet, and lay the

NetBackup 5000 on a grounded and ESD-free operating platform. For

details, see Error! Reference source not found. in Error! Reference

source not found.“Error! Reference source not found.”.

Step 4 Remove the disk modules. For details, see Error! Reference source

not found. to Error! Reference source not found. in Error!

Reference source not found.“Error! Reference source not found.”.

Step 5 Open the rear cover of the chassis. For details, see Error! Reference

source not found. in Error! Reference source not found.“Error!

Reference source not found.”.

Step 6 Remove the wind cover over the CPU cooling fin. For details, see

Error! Reference source not found. in Error! Reference source not

found.“Error! Reference source not found.”.

Step 7 Remove the DIMMs. For details, see Error! Reference source not

found. to Error! Reference source not found. in Error! Reference

source not found.“Error! Reference source not found.”.

Step 8 Remove the CPU and cooling fin. For details, see Error! Reference

source not found. to Error! Reference source not found. in Error!

Reference source not found.“Error! Reference source not found.”.

Step 9 Remove the RAID card. For details, see Error! Reference source not

found. to Error! Reference source not found. in Error! Reference

source not found.“Error! Reference source not found.”.

Step 10 Remove the NIC. For details, see Error! Reference source not found.

and Error! Reference source not found. in Error! Reference source

not found.“Error! Reference source not found.”.

Step 11 Move the new NetBackup 5000 chassis on the operating platform.

Step 12 Install the RAID card. For details, see Error! Reference source not

found. to Error! Reference source not found. in Error! Reference

source not found.“Error! Reference source not found.”.

Step 13 Install the NIC. For details, see Error! Reference source not found.

to Error! Reference source not found. in Error! Reference source

not found.“Error! Reference source not found.”.

Step 14 Connect the internal cables of the main board. For details, see the

instructions on the back of the rear cover of the NetBackup 5000

chassis.

Step 15 Install the CPU and cooling fin. For details, see Error! Reference

source not found. to Error! Reference source not found. in Error!

Reference source not found.“Error! Reference source not found.”.

NetBackup 5000 Chassis Replacement v. 1.3

NBU 5000 Chassis Replacement Guide v. 1.3

Step 16 Install the DIMMs. For details, see Error! Reference source not

found. to Error! Reference source not found. in Error! Reference

source not found.“Error! Reference source not found.”.

Step 17 Install the windshield over the CPU. For details, see Error! Reference

source not found. in Error! Reference source not found.“Error!

Reference source not found.”.

Step 18 Install the rear cover of the chassis. For details, see Error! Reference

source not found. in Error! Reference source not found.“Error!

Reference source not found.”.

Step 19 Install the disk modules. For details, see Error! Reference source not

found. to Error! Reference source not found. in Error! Reference

source not found.Error! Reference source not found..

Step 20 Install the new NetBackup 5000 into the cabinet. For details, see

Error! Reference source not found. in Error! Reference source not

found.“Error! Reference source not found.”.

Step 21 Connecting the NetBackup 5000 to the power socket and the KVM.

Step 22 Press the Power button on the rear of the cabinet to power on the

NetBackup 5000.

----End

Postrequisite

After the chassis is replaced, label the replaced chassis for the convenience of subsequent

handling.

After the chassis is replaced, perform the following procedure to set the time zone and date:

1. Connect the KVM on device, ensure CPU, memory and RAID card

message is correct in system self-test post;

2. Login with credentials: root/root.

3. Type yast at the command prompt to start the YaST control center.

Figure 1-2 YaST control center

NetBackup 5000 Chassis Replacement v. 1.3

NBU 5000 Chassis Replacement Guide v. 1.3

4. Use the arrow keys to locate System and Date and Time, and then press

Enter.

Figure 1-3 Selecting Date and Time

5. On the Clock and Time Zone interface, Under Time and Date, select

Change …, and then press Enter.

Figure 1-4 Setting the time zone

6. In the Change System Date and Time interface, set the date and time as

required, click Apply, and then press Enter.

NetBackup 5000 Chassis Replacement v. 1.3

NBU 5000 Chassis Replacement Guide v. 1.3

Figure 1-5 Setting the date and time

7. In the Clock and Time Zone interface, select Accept, and then press

Enter.

Figure 1-6 Confirming the changes

8. Quit the YaST control center.

9. Type the following commands to setup IPMI time:

service ipmi start

ipmitool sel time set "mm/dd/yyyy hh:mm:ss"

10. Type yast at the command prompt to start the YaST control center.

11. Select Network Devices, and select Network Card.

NetBackup 5000 Chassis Replacement v. 1.3

NBU 5000 Chassis Replacement Guide v. 1.3

Figure 1-7 Config network card

12. Select the network card which have been replaced, select Edit to go on.

Figure 1-8 Select network card

13. Input the IP address and Subnet Mask field, select Next to finish

configuration.

NetBackup 5000 Chassis Replacement v. 1.3

NBU 5000 Chassis Replacement Guide v. 1.3

Figure 1-9 Edit network card IP address

14. Select Quit.

15. Run the reboot command to reboot the NetBackup 5000.

----End

Symantec NetBackup 5000 Replacement Manual

Symantec NetBackup 5000 Replacement Manual

Symantec NetBackup 5000 Replacement Manual

Related papers

Other documents