Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Enlish p 1-26
Français p 27-29
Español p 30-32
Lot # 397442 10/26/16
Purchased: __________________
Be sure to ive us a rin before
makin any returns. 1-800-523-3987
Armoire
Shoal Creek Collection | Model 409934
WARNING
CHOKING HAZARD - Small Parts
Not for children under 3 years.
Adult assembly required.
Table of Contents Assembly Tools Required
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
2-3
4-5
6-26
27-29
30-32
33-34
35
Part Identifi cation
Hardware Identifi cation
Assembly Steps
Français
Español
Safety
Warranty
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D SHELF/BOTTOM (2)
D26 RIGHT DRAWER SIDE (1)
D27 LEFT DRAWER SIDE (1)
D174 DRAWER BACK (1)
D981 DRAWER BOTTOM (1)
E BACK (1)
F DOOR (2)
G2 ADJUSTABLE SHELF (2)
H RIGHT FRONT LEG (1)
I LEFT FRONT LEG (1)
J REAR LEG (2)
K DRAWER FRONT (1)
M64 DRAWER BRACE (1)
P END MOLDING (2)
å While not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identifi cation to help identify similar parts.
Now you know
our ABCs.
Part Identifi cation
409934 www.sauder.com/servicesPae 2
Part Identifi cation
409934www.sauder.com/services
Pae 3
A
B
C
D
E
F
G2
H
I
J
K
P
J
P
F
D
G2
D26
D981
D27
D174
M64
Hardware Identifi cation
å Screws are shown actual size. You may receive extra hardware with your unit.
409934 www.sauder.com/servicesPae 4
SAFETY BRACKET - 1
1G
HIDDEN CAM - 21
1F
METAL PIN - 8
1R
CAM SCREW - 9
8F
SLIDE CAM - 2
10A
22H
HINGE SPACER - 4
CAM DOWEL - 12
2F
KNOB - 5
24K
SHELF SNAP - 8
6R
FELT DISC CARD - 2
1M
NAIL - 43
1N
11L
WARNING LABEL - 1
(Refer to Step 19 for proper location and application)
WARNING AVERTISSEMENT ADVERTENCIA
Serious or fatal crushing injuries can
occur from furniture tipover.
To help prevent tipover:
• Install tipover restraint provided.
• Place heaviest items in the lower drawers.
• Unless specifi cally desined to
accommodate, do not set TVs or other
heavy objects on top of this product.
• Never allow children to climb or han on
drawers, doors, or shelves.
• Never open more than one drawer at a time.
(OR)
• Do not defeat or remove the drawer
interlock system.
Use of tipover restraints may only reduce,
but not eliminate, the risk of tipover.
This is a permanent label. Do not remove.
Des blessures graves ou fatales par écrasement
peuvent survenir si le mobilier bascule. Pour
prévenir le basculement:
• Installer le dispositif anti-basculement fourni.
• Placer les articles plus lourds dans les tiroirs inférieurs.
• Sauf si le meuble a été conçu spécialement à
cette fin, ne pas mettre de téléviseur ou d’autre
objets lourds sur le dessus de ce meuble.
• Ne jamais laisser d’enfants rimper sur les
tiroirs, les portes ou les étaères ou s’y aripper.
• Ne jamais ouvrir plus d’un tiroir à la fois.
(OU)
• Ne pas démanteler ou enlever le système de
verrouillae pour tiroir.
L’utilisation de dispositifs anti-basculement peut
réduire le risque de basculement, mais pas l’éliminer.
Cette étiquette est permanente. Ne pas l’enlever.
Lesiones graves o fatales por aplastamiento, pueden
ocurrir por el volcar de los muebles. Para ayudar a
prevenir que se volqué:
• Instalar la contención brindada para evitar que se volqué.
• Coloque los artículos más pesados en los cajones
inferiores.
• A menos que sea específicamente diseñado para
acomodar, no establezca televisores u otros objetos
pesados en la parte superior de este producto.
• Nunca permita que los niños se suban o se cueluen
de cajones, puertas o estantes.
• Nunca abra más de un cajón a la vez.
(O)
• No anule o elimine el sistema de bloqueo de los cajones.
El uso de la contención puede solamente reducir, pero
no eliminar, el riesgo de volcar.
Esta es una etiqueta permanente. No remover.
10/16 395783
35GA
CABINET RIGHT - 1
35GB
CABINET LEFT - 1
35GC
DRAWER RIGHT - 1
35GD
DRAWER LEFT - 1
METAL BRACKET - 2
4G 14H
HINGE - 4
Hardware Identifi cation
30S
BLACK 1-9/16" FLAT HEAD SCREW - 5
å Screws are shown actual size. You may receive extra hardware with your unit.
409934www.sauder.com/services
Pae 5
BLACK 1-1/8" MACHINE SCREW - 5
21S
BLACK 9/16" LARGE HEAD SCREW - 3
1S
BLACK 1-7/8" FLAT HEAD SCREW - 1
2S
BLACK 2-1/4" FLAT HEAD SCREW - 8
26S
GOLD 5/16" FLAT HEAD SCREW - 8
3S
SILVER 5/8" FLAT HEAD SCREW - 8
23S
BLACK 9/16" FLAT HEAD SCREW - 4
32S
Step 1
Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å
Assemble your unit on a carpeted fl oor or on the empty
carton to avoid scratchin your unit or the fl oor.
å
Push twenty-one HIDDEN CAMS (1F) into the ENDS (A
and B), SHELF/BOTTOMS (D), and DRAWER BRACE (M64).
Then, insert the metal end of twelve CAM DOWELS (2F)
into the HIDDEN CAMS, except the lon edes of the
ENDS (A and B) and the DRAWER BRACE (M64).
409934 www.sauder.com/servicesPae 6
(21 used)
(12 used)
Arrow
1F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not tihten the HIDDEN CAMS in this step.
A
B
D
D
Do not insert CAM DOWELS into these edes.
Do not insert CAM DOWELS into this part.
Arrow
Arrow
1F
The arrow in the HIDDEN
CAM must point toward the
hole in the ede of the board.
Hole
M64
Scan this QR code or go to this address:
http://qr.sauder.com/?ID=1618
to watch a video on how to assemble your unit.
å
Turn nine CAM SCREWS (8F) into the FRONT LEGS (H
and I) and DRAWER FRONT (K).
Step 2
409934www.sauder.com/services
Pae 7
K
H
I
8F
(9 used)
å
Fasten the CABINET RIGHT (35GA) to the RIGHT
END (A) and the CABINET LEFT (35GB) to the END (B).
Use four GOLD 5/16" FLAT HEAD SCREWS (3S) throuh
holes #1 and #3.
Step 3
409934 www.sauder.com/servicesPae 8
A
B
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
1
2
3
1
2
3
Roller end
Roller end
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
Lon ede with
HIDDEN CAMS
Lon ede with
HIDDEN CAMS
å
Fasten the REAR LEGS (J) to the ENDS (A and B). Use
eiht BLACK 2-1/4" FLAT HEAD SCREWS (26S).
Step 4
409934www.sauder.com/services
Pae 9
Remember:
Rihty tihty.
Lefty loosey.
A
B
J
J
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
These surfaces should be even.
Anled ede
Anled ede
BLACK 2-1/4" FLAT HEAD SCREW
(8 used in this step)
26S
å
Fasten one of the SHELF/BOTTOMS (D) to the ENDS (A
and B). Tihten four HIDDEN CAMS.
Step 5
409934 www.sauder.com/servicesPae 10
Start Tighten
Arrow
Minimum
190 derees
Caution
Risk of damae or
injury. HIDDEN CAMS
must be completely
tihtened. HIDDEN
CAMS that are not
completely tihtened
may loosen, and parts
may separate. To
completely tihten:
Arrow
Maximum
210 derees
A
B
D
Surface with
HIDDEN CAMS
Surface without
HIDDEN CAMS
Surface with
HIDDEN CAMS
J
J
Finished ede
Do not stand the unit upriht without the
BACK fastened. The unit may collapse.
Caution
Lon ede with
HIDDEN CAMS
Lon ede with
HIDDEN CAMS
å
Fasten the other SHELF/BOTTOM (D) to the ENDS (A
and B). Tihten four HIDDEN CAMS.
Step 6
409934www.sauder.com/services
Pae 11
A
B
D
Surface with
HIDDEN CAMS
Arrow
Minimum
190 derees
Maximum
210 derees
Finished ede
å
Fasten the TOP (C) to the ENDS (A and B). Tihten four
HIDDEN CAMS.
å
Fasten two METAL BRACKETS (4G) to the TOP (C). Use
two BLACK 9/16" LARGE HEAD SCREWS (1S).
Step 7
409934 www.sauder.com/servicesPae 12
A
B
C
4G
Surface with holes
Arrow
Minimum
190 derees
Maximum
210 derees
BLACK 9/16" LARGE HEAD SCREW
(2 used in this step)
1S
(2 used)
Lon fi nished ede
å
Turn four BLACK 9/16" FLAT HEAD SCREWS (32S) into
the ENDS (A and B) until the shoulders of the SCREWS
rest on the surfaces of the ENDS.
å
Slide the END MOLDINGS (P) onto the ENDS (A and B).
Line up the rooves in the MOLDINGS over the heads of
the SCREWS in the ENDS.
Step 8
409934www.sauder.com/services
Pae 13
A
B
P
P
P
BLACK 9/16" FLAT HEAD SCREW
(4 used in this step)
32S
Shoulder
Apply pressure with your hands
as you uide the MOLDINGS over
the SCREWS and onto the ENDS.
å
Fasten the FRONT LEGS (H and I) to the ENDS (A and B).
Tihten eiht HIDDEN CAMS.
Step 9
409934 www.sauder.com/servicesPae 14
1
2
A
B
H
I
Flat ede
Flat ede
Step 10
409934www.sauder.com/services
Pae 15
E
Printed
information
must be
facin up.
NAIL
(43 used in this step)
1N
These holes must line up over
the SHELF/BOTTOM (D).
Do not stand the unit upriht without the
BACK fastened. The unit may collapse.
Caution
å
Carefully turn your unit over onto its front edes. Unfold the
BACK (E) and lay it over your unit.
å
Make equal marins alon alon the two short edes and alon
the two lon edes of the BACK (E). Push on opposite corners of
your unit if needed to make it "square".
å
Fasten the BACK (E) to your unit usin the NAILS (1N).
å
NOTE: Be sure to tap NAILS into the holes that line up over the
SHELF/BOTTOM (D).
å
Fasten four HINGES (14H) and four HINGE SPACERS (22H)
to the DOORS (F). Use eiht SILVER 5/8" FLAT
HEAD SCREWS (23S).
Step 11
409934 www.sauder.com/servicesPae 16
F
F
14H
Don't worry. It isn't
Rome. This can be built
in a day.
SILVER 5/8" FLAT HEAD SCREW
(8 used in this step)
23S
22H
22H
14H
Step 12
409934www.sauder.com/services
Pae 17
å
Carefully stand your unit upriht.
å
Before fastenin the DOOR to your unit, be sure the
mountin screw is aainst the stops as shown in the
diaram. If it isn't, loosen the mountin screw to slide it
aainst the stops. Then tihten the mountin screw.
å
Fasten a DOOR (F) to the LEFT END (B) as shown in
the lower diaram. Use the screws in the HINGES. You
should start each SCREW a few turns before completely
tihtenin any of them.
å
Fasten a KNOB (24K) to the DOOR (F). Use a BLACK
1-1/8" MACHINE SCREW (21S).
å
Repeat this step for the other DOOR (F).
å
See the next step for DOOR adjustments.
F
B
24K
Want options? Customize
your item with add-on
hardware kits available
on sauder.com.
Mountin
screw
Stop
Hine
BLACK 1-1/8" MACHINE SCREW
(2 used for the KNOBS)
21S
Step 13
409934 www.sauder.com/servicesPae 18
å
Refer to the enlared diaram to identify the parts on the HINGES.
å
The DOORS may need some adjustments. Follow the text below to make needed adjustments.
å
DOOR ADJUSTMENTS:
To adjust the DOORS from side to side (horizontal) turn the adjustin screw in or out.
å
To adjust the DOORS up and down (vertical), loosen both vertical adjustment screws. Move the DOORS up or down to the
desired location. Tihten the screws after makin adjustments.
å
To adjust the DOORS in or out (depth), loosen the mountin screw one turn and move the DOORS in or out, as needed.
Tihten the mountin screw after makin adjustments.
Adjustin screw (horizontal)
Mountin screw (depth)
(vertical adjustment)
Step 14
409934www.sauder.com/services
Pae 19
å
Insert the DRAWER SIDES (D26 and D27) at
an angle into the slot at each end of the
DRAWER FRONT (K).
å
Slide the DRAWER BOTTOM (D981) into the grooves
in the DRAWER SIDES (D26 and D27) and
DRAWER FRONT (K).
å
Fasten the DRAWER BRACE (M64) to the
DRAWER FRONT (K). Tighten one HIDDEN CAM.
å
Fasten the DRAWER BACK (D174) to the DRAWER
SIDES (D26 and D27) and DRAWER BRACE (M64). Use
five BLACK 1-9/16" FLAT HEAD SCREWS (30S).
Surface with
HIDDEN CAM
12
34
Be sure the DRAWER
BOTTOM inserts into the
DRAWER FRONT roove.
Groove
Arrow
Maximum
210 derees
Minimum
190 derees
K
K
VIEW THE T-LOCK BOX VIDEO
Unfi nished
surface
K
D26
D981
D27
D174
D26
D27
D26
D27
Start each screw a few turns before
completely tihtenin any of them.
BLACK 1-9/16" FLAT HEAD SCREW
(5 used in this step)
30S
The tabs should insert freely
into the slots. Gently tilt the
DRAWER SIDES side to side
until the tabs slip into the slots.
With the palm of your hand,
tap the DRAWER BOTTOM
down into the roove.
M64
M64
å
Insert two SLIDE CAMS (10A) into the DRAWER SIDES (D26 and D27).
å
Fasten the DRAWER RIGHT (35GC) and DRAWER LEFT (35GD)
to the DRAWER SIDES (D26 and D27). Use four GOLD 5/16" FLAT
HEAD SCREWS (3S) throuh holes #1 and #3.
å
NOTE: The screw head in the CAM must be visible throuh the
slotted hole in the SLIDE.
Step 15
409934 www.sauder.com/servicesPae 20
10A
10A
1
2
3
1
2
3
Roller end
Roller end
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
Screw head - turn CAM to line up holes in
the SLIDES with holes in DRAWER SIDES
D26
D27
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
