Sauder 411885 User manual

Sauder
Brand
Sauder
Model
411885
Type
User manual
PLEASE CONTACT US
BEFORE RETURNING
YOUR UNIT TO THE STORE
1-800-523-3987
www.sauder.com
Made in the USA
Archbold, OH
NOTE: THIS INSTRUCTION BOOKLET CONTAINS
IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Lot #: 346761 09 / 25 / 12
Date Purchased: ____________________
English .................... Page 1-18
Français ...............Pages 19-21
Espanol .............Páginas 22-24
411885
Night Stand
ASSEMBLY TOOLS REQUIRED
Hammer
No. 2 Phillips Screwdriver
Tip Shown Actual Size
TABLE OF CONTENTS
Part Identifi cation .......................3
Hardware Identifi cation .............4
Assembly Steps ....................5-18
Français ..............................19-21
Espanol ...............................22-24
Safety .................................25-26
Warranty ...................................27
Page 2 www.sauder.com/services 411885
PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked
letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help
identify similar parts.
A RIGHT END 1
B LEFT END 1
C TOP 1
D BOTTOM 1
E BACK 1
F RIGHT FRONT LEG 1
G LEFT FRONT LEG 1
H BACK LEG 2
I DRAWER FRONT 1
J DRAWER BACK 1
K RIGHT DRAWER SIDE 1
L LEFT DRAWER SIDE 1
M DRAWER BOTTOM 1
N END MOLDING 2
Page 3
www.sauder.com/services411885
A
B
C
D
E
F
G
H
I
J
K
L
M
N
H
N
HARDWARE IDENTIFICATION
Screws are shown actual size. You may receive extra hardware with your unit.
Page 4 www.sauder.com/services 411885
RIGHT CABINET
RAIL - 1
O Q
RIGHT DRAWER
SLIDE - 1
R
LEFT DRAWER
SLIDE - 1
BLACK 1-1/8” MACHINE SCREW - 1
BB
BLACK 1-7/8" FLAT HEAD SCREW - 6
AA
HIDDEN CAM - 12
S2
CAM COVER - 2
V
CAM SCREW - 4
U2
GOLD 5/16" FLAT HEAD SCREW - 8
DD
NAIL - 18
EE
BLACK 9/16" FLAT HEAD SCREW - 4
CC
SLIDE CAM - 2
XW
CLIP - 2 TACK GLIDE - 4
Z
KNOB - 1
Y
LEFT CABINET
RAIL - 1
P
CAM DOWEL - 8
T2
1
1
S
t
e
p
Look for this icon. It means a video
assembly tip is available at:
www.sauder.com/services/tips
Assemble your unit on a carpeted fl oor or on the empty carton to avoid scratching your unit or the fl oor.
Push twelve HIDDEN CAMS (S2) into the ENDS (A and B) and BOTTOM (D) as shown in the upper diagrams. Then, insert the
metal end of a CAM DOWEL (T2) into each HIDDEN CAM, except in the long edges of the ENDS (A and B).
Turn four CAM SCREWS (U2) into the FRONT LEGS (F and G) as shown in the lower right diagrams.
Page 5
www.sauder.com/services411885
Do not tighten the HIDDEN CAMS in this step.
(8 used)
(4 used)
Do not insert CAM
DOWELS into these holes.
Do not insert
CAM DOWELS
into this edge.
(12 used)
A
B
F
G
D
U2
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Arrow
S2
Arrow
S2
Arrow
T2
S2
Page 6 www.sauder.com/services 411885
2
2
S
t
e
p
Carefully turn over the ENDS (A and B) and position them as shown with the surface without HIDDEN CAMS facing up.
Fasten the BACK LEGS (H) to the ENDS (A and B). Use six BLACK 1-7/8" FLAT HEAD SCREWS (AA).
A
H
H
BLACK 1-7/8” FLAT HEAD SCREW
(6 used in this step)
AA
Angled edge
These edges
should be even.
Surface without
HIDDEN CAMS
B
Surface without
HIDDEN CAMS
Page 7
www.sauder.com/services411885
3
3
S
t
e
p
Turn four BLACK 9/16” FLAT HEAD SCREWS (CC) into the ENDS (A and B) until the shoulder of the SCREWS rest on the surface
of the ENDS.
Slide the END MOLDINGS (N) onto the ENDS (A and B). Line up the groove in the MOLDINGS over the head of the SCREWS in
the ENDS.
Apply pressure with your hands as
you guide the MOLDINGS over
the SCREWS and onto the ENDS.
Shoulder
A
B
N
N
These edges
should be even.
BLACK 9/16" FLAT HEAD SCREW
(4 used in this step)
CC
These edges
should be even.
Page 8 www.sauder.com/services 411885
4
4
S
t
e
p
Carefully turn over the ENDS (A and B) and position them as shown with the surface with HIDDEN CAMS facing up.
Fasten the FRONT LEGS (F and G) to the ENDS (A and B). Tighten four HIDDEN CAMS.
B
G
F
Surface with
HIDDEN CAMS
A
Surface with
HIDDEN CAMS
Angled edge
Angled edge
These edges
should be even.
Page 9
www.sauder.com/services411885
5
5
S
t
e
p
Fasten the CABINET RAILS (O and P) to the ENDS (A and B). Use four GOLD 5/16” FLAT HEAD SCREWS (DD) through holes
1 and 3.
NOTE: The CABINET RAILS are marked "CABINET RIGHT" and "CABINET LEFT" for easy identification.
Roller end
GOLD 5/16” FLAT HEAD SCREW
(4 used in this step)
DD
1
3
O
P
B
A
Roller end
1
3
Page 10 www.sauder.com/services 411885
6
6
S
t
e
p
Fasten the LEFT END (B) to the TOP (C). Tighten two HIDDEN CAMS.
Fasten the BOTTOM (D) to the LEFT END (B). Tighten two HIDDEN CAMS.
B
C
D
Unfi nished surface
Unfi nished edge
Unfi nished surface
Finished edge
Caution
Risk of damage or
injury. Hidden Cams
must be completely
tightened. Hidden
Cams that are not
completely tightened
may loosen, and parts
may separate.
To completely tighten:
Start Tighten
Arrow
Maximum
210 degrees
Minimum
190 degrees
Arrow
Page 11
www.sauder.com/services411885
7
7
S
t
e
p
Fasten the RIGHT END (A) to the TOP (C) and BOTTOM (D). Tighten four HIDDEN CAMS.
C
D
A
Maximum
210 degrees
Minimum
190 degrees
Arrow
Page 12 www.sauder.com/services 411885
8
8
S
t
e
p
Carefully turn your unit over onto its front edges and lay the BACK (E) over your unit.
Make equal margins along the top and bottom edges of the BACK (E). Push on opposite corners of your unit if needed to make
it “square”.
Fasten the BACK (E) to your unit using the NAILS (EE).
Using your hammer, gently tap a TACK GLIDE (Z) into the end of each LEG (F, G, and H).
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
NAIL
(16 used in this step)
EE
E
Z
F
G
H
H
Unfi nished surface
Page 13
www.sauder.com/services411885
9
9
S
t
e
p
Insert the DRAWER SIDES (K and L) at an angle into the slot at each end of the DRAWER FRONT (I).
Slide the DRAWER BACK (J) into the grooves in the DRAWER SIDES (K and L) until the edge of the BACK is even with
the SIDES.
*U.S. Patent No. 6,413,007
I
These edges
should be even.
Groove
Groove
K
L
K
L
J
1
st
2
nd
Tab
Slot
K
I
The tabs should insert freely
into the slots. Gently tilt the
DRAWER SIDES side to side
until the tabs slip into the slots.
Page 14 www.sauder.com/services 411885
10
10
S
t
e
p
Slide the DRAWER BOTTOM (M) into the grooves in the DRAWER SIDES (K and L) and DRAWER FRONT (I).
Flip the drawer over and insert two CLIPS (W) into the groove in the DRAWER BACK (J) and wrap them over the DRAWER
BOTTOM (M). Tap a NAIL (EE) through each CLIP.
NOTE: The CLIPS should set in about 1” from the DRAWER SIDES.
Groove
M
W
K
L
J
M
I
1
st
2
nd
Unfi nished surface
NAIL
(2 used for the CLIPS)
EE
Be sure the DRAWER
BOTTOM inserts into the
DRAWER FRONT groove.
Page 15
www.sauder.com/services411885
11
11
S
t
e
p
R
Q
K
L
Screw head - turn CAM to
line up holes in SLIDES with
holes in DRAWER SIDES.
X
1
2
3
1
2
3
X
Roller end
Roller end
GOLD 5/16” FLAT HEAD SCREW
(4 used in this step)
DD
Insert a SLIDE CAM (X) into the DRAWER SIDES (K and L).
Fasten the DRAWER SLIDES (Q and R) to the DRAWER SIDES (K and L). Use four GOLD 5/16” FLAT HEAD SCREWS (DD)
through holes #1 and #3.
NOTE: The DRAWER SLIDES are marked “DRAWER RIGHT” and “DRAWER LEFT” for easy identification.
NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE.
Page 16 www.sauder.com/services 411885
12
12
S
t
e
p
Fasten the KNOB (Y) to the DRAWER FRONT (I). Use the BLACK 1-1/8" MACHINE SCREW (BB).
I
Y
BLACK 1-1/8” MACHINE SCREW
(1 used in this step)
BB
Page 17
www.sauder.com/services411885
13
13
S
t
e
p
Carefully stand your unit upright.
To insert the drawer into your unit, tip the front of the drawer down and drop the rollers on the drawer behind the rollers on the unit.
Lift the front of the drawer up and slide it into the unit.
Place the roller on the SLIDE
behind the roller on the RAIL.
14
14
S
t
e
p
Page 18 www.sauder.com/services 411885
To make adjustments to the drawer, loosen SCREW #3 in the SLIDES a 1/4 turn, then turn the CAM clockwise or counter-clockwise.
Notice how the drawer raises or lowers as you turn the CAM. The higher the screw in the oblong hole, the higher your drawer front
will be. The lower the screw, the lower the drawer front. By adjusting the drawer this way, it will help the DRAWER FRONT line up
better when closed. Tighten the SCREW when finished with adjustments.
Loosen screw #3 a 1/4 turn, turn the cam a 1/4 turn
maximum in both the clockwise and counter-clockwise
directions to make adjustments, and then tighten screw #3.
32
CamThe higher the screw in the oblong hole, the
higher your drawer front will be. The lower
the screw, the lower the drawer front.
15
15
S
t
e
p
Page 19
www.sauder.com/services411885
Push a CAM COVER (V) onto each HIDDEN CAM.
NOTE: Please read the back pages of the instruction booklet for important safety information.
This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry.
15 lbs.
40 lbs.
40 lbs.
To cover HIDDEN CAMS
V
A l’usage exclusif du
Canada Noter la date
d’achat de cet élément
et conserver le livret
pour future référence.
Pour contacter Sauder
en ce qui concerne cet
élément, faire référence
au numéro de lot et
numéro de modèle en
appelant notre numéro
sans frais.
Lot nº : ____________
Date de
l’achat: ____________
LISTE DE PIÈCES
REFERENCE DESCRIPTION QUANTITÉ
LISTE DE PIÈCES
REFERENCE DESCRIPTION QUANTITÉ
NOUS SOMMES LA POUR VOUS AIDER!
Nous faisons de notre mieux pour nous assurer que
votre meuble arrive dans d’excellentes conditions. Nos
représentants du service Clientèle sont aimables et prêts
à vous aider au cas où une pièce aurait été endommagée
ou manquerait (ou si vous aviez besoin d’aide pour
l’assemblage). NE RAMENEZ PAS LE MEUBLE AU
MAGASIN. Au Canada, composez ce numéro d’appel gratuit:
1-800-523-3987
Du lundi au vendredi, de 9 heures du matin à
5:30 heures du soir (horaire Côte Est)
(sauf jours fériés)
Si une pièce a besoin d’être remplacée, la pièce de
remplacement sera envoyée dans les 48 heures. (Sauf
week-ends et jours fériés)
Utilisez les instructions d’assemblage en français avec
les schémas étape par étape du manuel d’instruction
en anglais. Chaque étape en français correspond à la
même étape en anglais. La pièce devant être attachée
à l’élément est représentée en gris sur les schémas de
chaque étape pour plus de précision. Comparer la “Liste
de pièces” ci-dessous avec la “PART IDENTIFICATION”
du manuel en anglais pour vous familiariser avec les
pièces avant l’assemblage.
REMARQUE : CE MANUEL D’INSTRUCTIONS
CONTIENT D’IMPORTANTES INFORMATIONS
RELATIVES À LA SÉCURITÉ. À LIRE ET CONSERVER
POUR TOUTE RÉFÉRENCE FUTURE.
O GLISSIÈRE DROITE D'ÉLÉMENT ..1
P GLISSIÈRE GAUCHE D'ÉLÉMENT 1
Q COULISSE DROITE DE TIROIR .....1
R COULISSE GAUCHE DE TIROIR ...1
S2 EXCENTRIQUE ESCAMOTABLE .12
T2 CHEVILLE D'EXCENTRIQUE .........8
U2 VIS D'EXCENTRIQUE .....................4
V COUVERCLE D'EXCENTRIQUE ....2
W CLIP .................................................2
X EXCENTRIQUE DE COULISSE ......2
Y BOUTON ..........................................1
Z PATIN ...............................................4
AA VIS NOIRE TÊTE PLATE 48 mm .....6
BB VIS NOIRE À MÉTAUX 28 mm ........1
CC VIS NOIRE TÊTE PLATE 14 mm .....4
DD VIS DORÉE TÊTE PLATE 8 mm .....8
EE CLOU .............................................18
A EXTRÉMITÉ DROITE ......................1
B EXTRÉMITÉ GAUCHE ....................1
C DESSUS ..........................................1
D DESSOUS .......................................1
E ARRIÈRE .........................................1
F PIED AVANT DROIT ........................1
G PIED AVANT GAUCHE ....................1
H PIED ARRIÈRE ................................2
I DEVANT DE TIROIR ........................1
J ARRIÈRE DE TIROIR ......................1
K CÔTÉ DROIT DE TIROIR ................1
L CÔTÉ GAUCHE DE TIROIR ............1
M FOND DE TIROIR ............................1
N MOULURE D’EXTRÉMITÉ ..............2
Chevet411885
Page 20 www.sauder.com/services 411885
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Sauder 411885 User manual

Sauder
Brand
Sauder
Model
411885
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents