Ricoh PJ WX4153 Operating instructions

For safe and correct use, be sure to read Safety Information before

using the machine.

Appendix

Troubleshooting

Before Using RICOH PJ Interactive Kit Type3

Operating

Instructions

TABLE OF CONTENTS

Introduction......................................................................................................................................................... 2

How to Read This Manual................................................................................................................................. 3

Symbols...........................................................................................................................................................3

Disclaimer........................................................................................................................................................3

Notes...............................................................................................................................................................3

1. Before Using RICOH PJ Interactive Kit Type3

RICOH PJ Interactive Kit Type3 Overview....................................................................................................... 5

Checking the Contents of the Product............................................................................................................... 7

Preparations for Using the Interactive Function................................................................................................9

Attaching the Interactive Sensor to the Projector.......................................................................................10

Installing the Supplied Software on a Computer...................................................................................... 15

Connecting the Projector and a Computer................................................................................................ 16

Aligning Pen Recognition Positions.............................................................................................................17

Using the Interactive Pen..................................................................................................................................20

Interactive Pen Parts and Their Functions................................................................................................... 20

How to Use the Interactive Pen...................................................................................................................20

Installing Batteries into the Interactive Pen................................................................................................. 21

Replacing the Pen Nib.................................................................................................................................22

2. Troubleshooting

What to Do When a Message Is Displayed..................................................................................................25

RICOH PJ Interactive Setup Software Message........................................................................................25

When the Projected Screen Cannot Be Operated........................................................................................27

When the Projected Screen Cannot Be Operated As Wanted....................................................................29

3. Appendix

Trademarks....................................................................................................................................................... 31

Introduction

This manual contains detailed instructions and notes on the operation and use of this product. For your

safety and benefit, read this manual carefully before using the product. Keep this manual in a handy

place for quick reference.

How to Read This Manual

Symbols

This manual uses the following symbols:

Indicates points to pay attention to when using functions. This symbol indicates points that may result in

the product or service becoming unusable or result in the loss of data if the instructions are not obeyed.

Be sure to read these explanations.

Indicates supplementary explanations of the product's functions and instructions on resolving user errors.

[ ]

Indicates the names of keys or buttons on the product or display.

Disclaimer

To the maximum extent permitted by applicable laws, in no event will the manufacturer be liable for any

damages whatsoever arising out of failures of this product, losses of documents or data, or the use or

non-use of this product and operation manuals provided with it.

Make sure that you always copy or have backups of important documents or data. Documents or data

might be erased due to your operational errors or malfunctions of the machine. Also, you are

responsible for taking protective measures against computer viruses, worms, and other harmful software.

In no event will the manufacturer be responsible for any documents created by you using this product or

any results from the data executed by you.

Notes

Contents of this manual are subject to change without prior notice.

Some illustrations or explanations in this guide may differ from your product due to improvement or

change in the product.

1. Before Using RICOH PJ Interactive

Kit Type3

This chapter provides an overview of RICOH PJ Interactive Kit Type3 and describes its basic operations.

RICOH PJ Interactive Kit Type3 Overview

With this product, you can operate a computer screen projected on the screen. With "RICOH Interactive

Whiteboard Lt", the software that comes with this product, you can write information and perform

various other operations on the screen.

RICOH PJ Interactive Kit Type3 can be used with the following projectors:

• RICOH PJ WX4153 series

• RICOH PJ WUC4650/WXC4660 series

To perform various operations on the screen, it is necessary to configure the interactive function on both

the projector and the computer. For information about how to configure the interactive function, see

page 9 "Preparations for Using the Interactive Function".

Visual overview of using the product with the RICOH PJ WX4153 series

PDF

Y0E5IX0061

Visual overview of using the product with the RICOH PJ WUC4650/WXC4660 series

PDF

Y0E5IX0062

1. Before Using RICOH PJ Interactive Kit Type3

Checking the Contents of the Product

The following accessories are packaged with the product. Make sure all of these accessories are

included.

Accessories Usage

Interactive sensor

Y0E5IX0071

Attach this to the projector.

For details about how to attach the interactive sensor,

see page 10 "Attaching the Interactive Sensor to the

Projector".

Interactive pen × 2

Y0E5IX0072

Use this pen to manipulate and perform operations on

the computer screen projected by the projector.

The interactive pen is only to be used with this product.

Do not use this pen with any other products. Likewise,

do not use any other pens with this product.

For details about the interactive pen, see page 20

"Using the Interactive Pen".

Interactive pen replacement nib × 5

Y0E5IX0073

Replace the pen nib of the interactive pen if it is

damaged or lost.

For details about how to replace the pen nib, see

page 22 "Replacing the Pen Nib".

Cable clip for the RICOH PJ WX4153

series × 2

Y0E5IX0073

Attach this to the RICOH PJ WX4153 series and secure

the USB cable.

For details about how to attach the cable clip, see

page 11 "Attaching the interactive sensor to the

RICOH PJ WX4153 series".

Checking the Contents of the Product

Accessories Usage

Attachment for the RICOH PJ WUC4650/

WXC4660 series

Y0E5IX0081

Used when attaching the interactive sensor to the

RICOH PJ WUC4650/WXC4660 series.

For details about how to attach the interactive sensor to

the RICOH PJ WUC4650/WXC4660 series, see

page 13 "Attaching the interactive sensor to the

RICOH PJ WUC4650/WXC4660 series".

Hexagon wrench (2 mm)

Y0E5IX0082

Used when attaching the interactive sensor to a

projector or attachment.

USB cable

Y0E5IX0083

Used to connect the interactive sensor to the computer.

For details about how to connect the interactive sensor

to the computer, see page 16 "Connecting the

Projector and a Computer".

• CD-ROM

• Battery (four AAA batteries for the interactive pen)

• Operating Instructions (Interactive Function) (This manual)

• Other documents

1. Before Using RICOH PJ Interactive Kit Type3

Preparations for Using the Interactive Function

• Do not use the projector near a radio transmitter, television, copier, air conditioner, or other device

that may generate electromagnetic waves or radio frequencies.

• Do not use the projector in a dusty, extremely high- or low-temperature or humid environment.

• Keep any magnetic or static materials away from the camera lens in the interactive sensor.

Otherwise, the interactive function could experience interference.

• To use the interactive function, you must use an RGB cable or an HDMI cable to connect the

projector and computer.

• In Windows, use a duplicate desktop for projection instead of an extended desktop.

• When using the interactive function, using the projector remote control may cause unexpected

operations.

Operating a computer on the projection screen with the interactive pen

The interactive function allows you to operate a computer connected to the projector directly on the

projection screen.

Writing and drawing on a projected screen

You can also write and draw on a projected screen using the included software "RICOH Interactive

Whiteboard Lt".

To use the interactive function, the following settings are required:

To use the interactive function with the RICOH PJ WX4153 series

Y0E5IX0026

Preparations for Using the Interactive Function

To use the interactive function with the RICOH PJ WUC4650/WXC4660 series

Y0E5IX0063

Step Setting Contents Reference

1 Attach the interactive sensor to the projector. See page 10 "Attaching the

Interactive Sensor to the

Projector".

2 Install the software that comes with this product

on a computer.

See page 15 "Installing the

Supplied Software on a

Computer".

3 Connect the projector and a computer. See page 16 "Connecting the

Projector and a Computer".

4 Align pen recognition positions using the

RICOH PJ Interactive Setup Software.

See page 17 "Aligning Pen

Recognition Positions".

Attaching the Interactive Sensor to the Projector

This section explains how to attach the interactive sensor to the projector.

• Do not lift the projector by holding the attached interactive sensor.

• Avoid applying excessive force to the interactive sensor when operating the projector.

1. Before Using RICOH PJ Interactive Kit Type3

Attaching the interactive sensor to the RICOH PJ WX4153 series

1. Remove the top cover of the projector.

Loosen the screws by using the hexagon wrench, and then hold the screws and lift them upward

together.

Y0E5IX0027

Pull out the power cables.

Pull out the tape.

Y0E5IX0028

3. Connect the power cables to the interactive sensor.

Y0E5IX0029

Preparations for Using the Interactive Function

4. Hook the cords onto the protrusion.

Y0E5IX0031

5. Screw in the interactive sensor.

Fasten the two locations by using the hexagon wrench.

Y0E5IX0030

6. Attach the cable clips to the projector.

Attach the cable clips to the top and bottom of the intake vents on the right side of the projector,

avoiding the intake vents.

Y0E5IX0032

1. Before Using RICOH PJ Interactive Kit Type3

Attaching the interactive sensor to the RICOH PJ WUC4650/WXC4660 series

• Highly adhesive double-sided tape is used to secure the attachment.

• Be careful not to touch the adhesive surface of the tape.

• Be careful of the position and orientation when attaching the attachment.

Correctly oriented

Y0E5IX0088

Incorrectly oriented

Y0E5IX0089

Attachment reference

Y0E5IX0090

Preparations for Using the Interactive Function

1. Attachment reference 1

2. Attachment reference 2

1. Gently wipe away any dirt from where the attachment is to be secured.

Y0E5IX0087

2. See the orientation of the attachment and the references for securing it.

3. Peel the release liner off the double-sided tape, and then align the edge of the attachment

with the attachment reference 1 groove.

Y0E5IX0035

4. Align the corner of the attachment with the attachment reference 2 groove, and then

secure the attachment to the projector.

Fully push the attachment onto the projector.

Y0E5IX0079

1. Before Using RICOH PJ Interactive Kit Type3

5. Screw in the interactive sensor.

Fasten the two locations by using the hexagon wrench.

Y0E5IX0036

Installing the Supplied Software on a Computer

To write and draw on a projection screen, install the RICOH PJ Interactive Setup Software and RICOH

Interactive Whiteboard Lt on a computer.

For details about how to use the RICOH PJ Interactive Setup Software, see page 17 "Aligning Pen

Recognition Positions". For details about how to use RICOH Interactive Whiteboard Lt, see Operating

Instructions provided with RICOH Interactive Whiteboard Lt.

• To install the software on a computer, log on as a user with administrator privileges.

1. Insert the CD-ROM in the CD-ROM drive of your computer.

2. Select the language for the installation, and then click [Select].

3. Click [Setup Software].

4. Click [Install] under "Installation of RICOH PJ Interactive Setup Software".

5. When the installation has completed, click [Next].

6. Click [Install] under "Installation of RICOH Interactive Whiteboard Lt".

7. When the installation has completed, click [Complete].

8. Click [Exit].

• If the [User Account Control] dialog box appears during the installation procedure, click [Yes] or

[Continue].

• To uninstall the software, use the program delete function in [Control Panel] to delete the software.

Preparations for Using the Interactive Function

Connecting the Projector and a Computer

This section explains how to connect the projector and a computer.

1. Connect the computer to the projector using RGB cables or an HDMI cable.

For the connection procedure, see the operating instructions provided with the projector.

Y0E5IX0033

Y0E5IX0077

2. Connect the USB cable.

Y0E5IX0034

1. Before Using RICOH PJ Interactive Kit Type3

3. Hold the cable with the cable clip.

Y0E5IX0080

Aligning Pen Recognition Positions

Once pen recognition positions are aligned, you can directly operate the computer display on the

screen.

• Realign pen recognition positions in case of the following:

• After moving the projector

• After changing the input signal resolution

• After changing the display area with a function such as "Zoom" or "Aspect"

• Use one of the computer screen resolutions listed below. If any other resolution is used, the

interactive function may not work normally.

• 1024×768

• 1280×800

• 1366×768

• 1920×1080

1. Turn on the projector to project the screen.

To turn on the projector or project the screen, see the operating instructions provided with the

projector.

2. Project the computer screen on the projector screen.

For the projecting procedure, see the operating instructions provided with the projector.

3. Start the RICOH PJ Interactive Setup Software.

4. When the images are projected in "Rear" or "Ceiling" mode, select the appropriate

projection mode under "Options" according to how the projector is positioned.

5. Click [Start Adjustment] under "STEP 1 Adjust Sensor Angle".

Preparations for Using the Interactive Function

6. Adjust the angle of the sensor so the projected image fits within the blue frame.

Adjust brightness of the sensor when the projected image is blurred.

Adjust the camera angle by using the hexagon wrench to make the bottom of the projected image

as close to the bottom of the blue frame as possible.

Y0E5IX0037

Y0E5IX0078

7. Click [Finish].

8. Click [Alignment] under "STEP 2 Alignment".

9. Click [Auto Alignment].

• Returns to previous screen if successful.

• If it fails, an error message is displayed. Try again.

1. Before Using RICOH PJ Interactive Kit Type3

Ricoh PJ WX4153, PJ WX4153N Operating instructions

Related papers

Other documents