7/16
(11.1mm)
5/16 (8mm)
3/8
(9.5mm)
3/8
(9.5mm)
A
B
3-3/
8
(85.7mm)
Pull Side of Door Pull Side of Door
Push Side of Door Push Side of Door
THIS IS A LEFT HAND DOOR
THIS IS A RIGHT HAND DOOR
CLOSIN
G SPEED
LATCHING
SPEED
CLOSING
VALVE
LATCH
VALVE
Regul
ar Arm Installation
Closer installs on PULL/HINGE
side of door
DOOR CLO
SER ADJUSTMENTS
NOTE Closing arcs("CLOSE"and"LATCH") are controlled by two(2)separate speed adjusting valves.
Adjust the CLOSING speed at first and then adjust the LATCHING speed.
1. "CLOSING"speed adjustment is accomplished by full rotations of the speed adjusting valve.
-Turn the speed adjusting valve CLOCKWISE for a SLOWER closing speed.
-Turn the speed adjusting valve COUNTER-CLOCKWISE for a FASTER closing speed.
2 "LATCH" speed adjustment is accomplished by full rotations of the speed adjusting valve.
-Turn the speed adjusting screw CLOCKWISE for a SLOWER closing speed.
-Turn the speed adjusting screw COUNTER-CLOCKWISE for a FASTER closing speed.
1. Select door opening angle and use dimensions shown above .
Mark four (4) holes on door for door closer and four(4) holes underside of frame for paralle l bracket.
2. Drill pilot holes in door leaf and frame for #14 all-purpose screws for wood door/frame.
Or drill and tap for 1/4-20 machine screws for metal door/frame.
3. Mount closer on door using provided screws.
SPEED ADJUSTING VALVE MUST BE POSITIONED AWAY FROM HINGE EDGE
4. Install parallel Arm Bracket to frame using provided screws.
5. Using a wrench on the square shaft at bottom of closer, rotate shaft approximately 45 degrees toward hinge edge of door.
Hold and place main arm on top shaft of closer at proper index mark as illustrated.
FOR LEFT HAND DOOR "L"(illustration " A"). FOR RIGHT HAND DOOR "R"(illustration "B").
Tighten arm screw with Lock-washer securely.
6. Remove arm shoe from forearm and discard. Install rod end of forearm to bracket using provided screw/washer assembly.
7. Adjust length of adjustable forearm so that main arm is parallel to frame.
8. Adjust the door closer, following instuctions as shown on page 1.
PARALLEL ARM (P
USH SIDE) Mounting
TO 180° OPENINGS.
Left hand door shown
Right hand door opposite
Dimensions are in inches (mm)
Do not scale drawing
Top Jamb Insta
llation
Closer Installs on Frame on
PUSH/STOP side of door.
Parallel A
rm Installation
Closer installs on PUSH/STOP
side of door. * Optional
3/4
(19mm)
Parallel bracket
9-1/16
(230.2mm)
2-3/4
(69.8mm)
OPENING
To 120
120 -180
DIM.A
10 3/4
(273mm)
6 15/16
(176.2mm)
4 3/4
(120.6mm)
8 3/4
(222.2mm)
DIM.B
Hinge or Pivot
Page: 1
P
age: 4
illustrated
Non Hold Open Arm
Left Hand Door-LH
Right Hand Reverse -RHR
See Page 2
illustrated
Non Hold Open Arm
Right Hand Door-RH
Left Hand Reverse -LHR
See Page 3
illustrated
Non Hold Open Arm
Right Hand Door-RH
Left Hand Reverse -LHR
See Page 4
Hinge Ed
ge
of Door
Hinge Edge
of Door
5400 Series Non-Hold Open Door Closer
Installation Instructions
Adjust
able 2-5
CHART TO
DETERMINE HAND
OF DOOR
NOTE: T
hese instructions apply only to closers equipped with backcheck action.
To increase backcheck intensity, turn "BC" valve clockwise.
To decrease backcheck intensity , turn"BC" Valve counter-clockwise.
OPENING CYCLE
INCREASE
DECREASE
Never close This
valve completely
BACKCHECK ADJUSTMENT
Backcheck
Range
CLOSING CYCLE
*ADJUST SPRING TENSION ACCORDING TO THE
DOOR WIDTH & WEIGHT
INCREASE
DECREASE
NOTE: MAX 16 TURNS FROM MINIMUM SETTING
SPRING
P
OWER
FULL TURNS
OF SPRING
ADJUSTING
NUT
MAX
DOOR
WEIGHT
(kg)
1 -5
45 2 0
65 3 5
85 4 11
25
INSTALLATION SEQUENCE
(A) (B)
Parallel arm Insta
llation
Speed
screws
Right
hand door
Left hand door
S
R
L
S
L
R
45° 45°
BC
BC
HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 - (800) 325-9995 - Fax (800) 782-0149
HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 - (800) 325-9995 - Fax (800) 782-0149
I-CL00796 Rev. 4
6-12-2020
*
ADJUST SPRING TENSION ACCORDING TO THE
DOOR WIDTH & WEIGHT
A
6-1/2
(165.1mm)
1-3/4(44.4mm)
1(25.4mm)
9-1/16(230.2mm)
3/4(19mm)
1-1/8(28.5mm)
A
9-1/16(230.2mm)
3/4(19mm)
1/2(12.7mm)
6-1/14
(158.7mm)
1-3/4(44.4mm)
1-3/4(44.4mm)
H
inge
or
Pivot
Righ
t hand door shown
Left hand door opposite
Dimensions are in inches(mm)
Do not scale drawing
O
PENING
To120
12
0
-18
0
6-1
/2(165.1mm)
DIM.A
4(101.6mm)
1. S
elect door opening angle and use dimensions shown above.
M
ark four (4) holes on door leaf for closer body and two (2) holes on frame for arm shoe.
2.
Drill pilot holes in door leaf and frame for #14 all-purpose screws for wood door/frame.
Or drill and tap for 1/4-20 machine screws for metal door/frame
3. Install forearm/arm shoe assembly to frame using provided screws.
4.
Mount closer on door using provided screws. SPEED ADJUSTING VALVE MUST BE POSITIONED TOWARD
HINGE EDGE
5.
Install main arm to top pinion shaft, perpendicular to door. Secure tightly with provided arm screw/washer assembly.
6.
Adjust length of forearm so that forearm is perpendicular to frame when assembled to preloaded main arm (see below
iIlustration). Secure forearm to main arm with provided screw/washer assembly
7.
Snap pinion cap over shaft at bottom of closer. If the slim cover is packed, please fix it by provided screws.
8.
Adjust the door closer, following instructions as shown on page 1.
INS
TALLATION
SEQU
ENCE
N
OTE: MAX 16 TURNS FROM MINIMUM SETTING
REGULAR ARM (PULL SIDE) Mounting
TO 180° OPENINGS.
H
inge
or
Pivot
TOP JAMB (PUSH SIDE) Mounting
TO 180° OPENINGS.
L
eft Hand Door
Right Hand Door
Top View Typical Installation
SPEED
ADJUSTING
SCREW
SPEED
ADJUSTING
SCREW
"BC"
ADJUSTING SCREW
Preload Preload
R
ight hand door Left hand door
O
PENING DIM. A
To 120
120 -
180
6
1/2(165.1mm)
4(101.6mm)
"BC"
ADJUSTING SCREW
Preload Preload
SPEED
ADJUSTING
SCREW
SPEED
ADJUSTING
SCREW
s
L
R
s
L
R
Top View Typical Installation
Page
: 2
Page: 3
1.
Select door opening angle and use dimensions shown above.
Mark four (4) holes on door frame for closer body and two (2) holes on door leaf for arm shoe.
2. Drill pilot holes in door leaf and frame for #14 all-purpose screws for wood door/frame.
Or drill and tap for 1/4-20 machine screws for metal door/frame
3. Install forearm/arm shoe assembly to door leaf using provided screws.
4. Mount closer on door frame using provided screws. SPEED ADJUSTING VALVE MUST BE POSITIONED TOWARD
HINGE EDGE
5. Install main arm to bottom pinion shaft, perpendicular to door frame.
Secure it tightly with provided arm screw/washerassembly.
6. Adjust length of forearm so that forearm is perpendicular to door leaf when assembled to preloaded main arm (see below
iIlustration). Secure forearm to main arm with provided screw/washer assembly
7. Snap pinion cap over shaft at top of closer. If the slim cover is packed, please fix it by provided screws.
8. Adjust the door closer, following instructions as shown on page 1.
INS
TALLATION
SEQU
ENCE
Left hand door shown
Right hand door opposite
Dimensions are in inches(mm)
Do not scale drawing
*
ADJUST SPRING TENSION ACCORDING TO THE
DOOR WIDTH & WEIGHT
N
OTE: MAX 16 TURNS FROM MINIMUM SETTING
INCREASE
DECRE
ASE
SPRIN
G
POWER
FULL TURNS
OF SPRING
ADJUSTING
NUT
MAX
DOOR
WEIGHT
(kg)
2 -5
65 3 0
85 4 5
120 5 11
45
BC
INCREASE
DECREA
SE
SPRIN
G
POWER
FULL TURNS
OF SPRING
ADJUSTING
NUT
MAX
DOOR
WEIGHT
(kg)
2 -5
65 3 0
85 4 5
120 5 11
45
BC
s
L
R
s
L
R
H
AGER COMPANIES 139 Victor Street, St. Louis, MO 63104 - (800) 325-9995 - Fax (800) 782-0149
HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 - (800) 325-9995 - Fax (800) 782-0149
*
ADJUST SPRING TENSION ACCORDING TO THE
DOOR WIDTH & WEIGHT
A
6-1/2
(165.1mm)
1-3/4(44.4mm)
1(25.4mm)
9-1/16(230.2mm)
3/4(19mm)
1-1/8(28.5mm)
A
9-1/16(230.2mm)
3/4(19mm)
1/2(12.7mm)
6-1/14
(158.7mm)
1-3/4(44.4mm)
1-3/4(44.4mm)
H
inge
or
Pivot
Righ
t hand door shown
Left hand door opposite
Dimensions are in inches(mm)
Do not scale drawing
O
PENING
To120
12
0
-18
0
6-1
/2(165.1mm)
DIM.A
4(101.6mm)
1. Select door opening angle and use dimensions shown above.
Mark four (4) holes on door leaf for closer body and two (2) holes on frame for arm shoe.
2. Drill pilot holes in door leaf and frame for #14 all-purpose screws for wood door/frame.
Or drill and tap for 1/4-20 machine screws for metal door/frame
3. Install forearm/arm shoe assembly to frame using provided screws.
4. Mount closer on door using provided screws. SPEED ADJUSTING VALVE MUST BE POSITIONED TOWARD
HINGE EDGE
5. Install main arm to top pinion shaft, perpendicular to door. Secure tightly with provided arm screw/washer assembly.
6. Adjust length of forearm so that forearm is perpendicular to frame when assembled to preloaded main arm (see below
iIlustration). Secure forearm to main arm with provided screw/washer assembly
7. Snap pinion cap over shaft at bottom of closer. If the slim cover is packed, please fix it by provided screws.
8. Adjust the door closer, following instructions as shown on page 1.
INS
TALLATION
SEQU
ENCE
N
OTE: MAX 16 TURNS FROM MINIMUM SETTING
REGULAR ARM (PULL SIDE) Mounting
TO 180° OPENINGS.
H
inge
or
Pivot
TOP JAMB (PUSH SIDE) Mounting
TO 180° OPENINGS.
L
eft Hand Door
Right Hand Door
Top View Typical Installation
SPEED
ADJUSTING
SCREW
SPEED
ADJUSTING
SCREW
"BC"
ADJUSTING SCREW
Preload Preload
R
ight hand door Left hand door
O
PENING DIM. A
To 120
120 -
180
6
1/2(165.1mm)
4(101.6mm)
"BC"
ADJUSTING SCREW
Preload Preload
SPEED
ADJUSTING
SCREW
SPEED
ADJUSTING
SCREW
s
L
R
s
L
R
Top View Typical Installation
Page
: 2
Page: 3
1. S
elect door opening angle and use dimensions shown above.
M
ark four (4) holes on door frame for closer body and two (2) holes on door leaf for arm shoe.
2.
Drill pilot holes in door leaf and frame for #14 all-purpose screws for wood door/frame.
O
r drill and tap for 1/4-20 machine screws for metal door/frame
3.
Install forearm/arm shoe assembly to door leaf using provided screws.
4. Mount closer on door frame using provided screws. SPEED ADJUSTING VALVE MUST BE POSITIONED TOWARD
HINGE EDGE
5.
Install main arm to bottom pinion shaft, perpendicular to door frame.
Secure it tightly with provided arm screw/washerassembly.
6.
Adjust length of forearm so that forearm is perpendicular to door leaf when assembled to preloaded main arm (see below
iIlustration). Secure forearm to main arm with provided screw/washer assembly
7.
Snap pinion cap over shaft at top of closer. If the slim cover is packed, please fix it by provided screws.
8.
Adjust the door closer, following instructions as shown on page 1.
INS
TALLATION
SEQU
ENCE
Left hand door shown
Right hand door opposite
Dimensions are in inches(mm)
Do not scale drawing
*
ADJUST SPRING TENSION ACCORDING TO THE
DOOR WIDTH & WEIGHT
N
OTE: MAX 16 TURNS FROM MINIMUM SETTING
INCREASE
DECRE
ASE
SPRIN
G
POWER
FULL TURNS
OF SPRING
ADJUSTING
NUT
MAX
DOOR
WEIGHT
(kg)
2 -5
65 3 0
85 4 5
120 5 11
45
BC
INCREASE
DECREA
SE
SPRIN
G
POWER
FULL TURNS
OF SPRING
ADJUSTING
NUT
MAX
DOOR
WEIGHT
(kg)
2 -5
65 3 0
85 4 5
120 5 11
45
BC
s
L
R
s
L
R
H
AGER COMPANIES 139 Victor Street, St. Louis, MO 63104 - (800) 325-9995 - Fax (800) 782-0149
HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 - (800) 325-9995 - Fax (800) 782-0149
7/16
(11.1mm)
5/16 (8mm)
3/8
(9.5mm)
3/8
(9.5mm)
A
B
3-
3/8
(85.7mm)
Pull Side of Door Pull Side of Door
Push Side of Door Push Side of Door
THIS IS A LEFT HAND DOOR
THIS IS A RIGHT HAND DOOR
CLO
SING SPEED
LATCHING
SPEED
CLOSING
VALVE
LATCH
VALVE
Reg
ular Arm Installation
Closer installs on PULL/HINGE
side of door
DO
OR CLOSER ADJUSTMENTS
NOTE Closing arcs("CLOSE"and"LATCH") are controlled by two(2)separate speed adjusting valves.
Adjust the CLOSING speed at first and then adjust the LATCHING speed.
1. "CLOSING"speed adjustment is accomplished by full rotations of the speed adjusting valve.
-Turn the speed adjusting valve CLOCKWISE for a SLOWER closing speed.
-Turn the speed adjusting valve COUNTER-CLOCKWISE for a FASTER closing speed.
2 "LATCH" speed adjustment is accomplished by full rotations of the speed adjusting valve.
-Turn the speed adjusting screw CLOCKWISE for a SLOWER closing speed.
-Turn the speed adjusting screw COUNTER-CLOCKWISE for a FASTER closing speed.
1. Select door opening angle and use dimensions shown above .
Mark four (4) holes on door for door closer and four(4) holes underside of frame for paralle l bracket.
2. Drill pilot holes in door leaf and frame for #14 all-purpose screws for wood door/frame.
Or drill and tap for 1/4-20 machine screws for metal door/frame.
3. Mount closer on door using provided screws.
SPEED ADJUSTING VALVE MUST BE POSITIONED AWAY FROM HINGE EDGE
4. Install parallel Arm Bracket to frame using provided screws.
5. Using a wrench on the square shaft at bottom of closer, rotate shaft approximately 45 degrees toward hinge edge of door.
Hold and place main arm on top shaft of closer at proper index mark as illustrated.
FOR LEFT HAND DOOR "L"(illustration " A"). FOR RIGHT HAND DOOR "R"(illustration "B").
Tighten arm screw with Lock-washer securely.
6. Remove arm shoe from forearm and discard. Install rod end of forearm to bracket using provided screw/washer assembly.
7. Adjust length of adjustable forearm so that main arm is parallel to frame.
8. Adjust the door closer, following instuctions as shown on page 1.
PARALLE
L ARM (PUSH SIDE) Mounting
TO 180° OPENINGS.
Left hand door shown
Right hand door opposite
Dimensions are in inches (mm)
Do not scale drawing
Top Jamb In
stallation
Closer Installs on Frame on
PUSH/STOP side of door.
Pa
rallel Arm Installation
Closer installs on PUSH/STOP
side of door. * Optional
3/4
(19mm)
Parallel bracket
9-1/16
(230.2mm)
2-3/4
(69.8mm)
OPENING
To 120
120 -180
DIM.A
10 3/4
(273mm)
6 15/16
(176.2mm)
4 3/4
(120.6mm)
8 3/4
(222.2mm)
DIM.B
Hinge or Pivot
Page
: 1
Page: 4
illustrated
Non Hold Open Arm
Left Hand Door-LH
Right Hand Reverse -RHR
See Page 2
illustrated
Non Hold Open Arm
Right Hand Door-RH
Left Hand Reverse -LHR
See Page 3
illustrated
Non Hold Open Arm
Right Hand Door-RH
Left Hand Reverse -LHR
See Page 4
Hi
nge Edge
of Door
Hinge Edge
of Door
5400 Series Non-Hold Open Door Closer
Installation Instructions
Adj
ustable 2-5
CHART TO
DETERMINE HAND
OF DOOR
NOT
E: These instructions apply only to closers equipped with backcheck action.
To increase backcheck intensity, turn "BC" valve clockwise.
To decrease backcheck intensity , turn"BC" Valve counter-clockwise.
OPENING CYCLE
INCREASE
DECREASE
Never close This
valve completely
BACKCHECK ADJUSTMENT
Backcheck
Range
CLOSING CYCLE
*ADJUST SPRING TENSION ACCORDING TO THE
DOOR WIDTH & WEIGHT
INCREASE
DECREASE
NOTE: MAX 16 TURNS FROM MINIMUM SETTING
SPR
ING
POWER
FULL TURNS
OF SPRING
ADJUSTING
NUT
MAX
DOOR
WEIGHT
(kg)
1 -5
45 2 0
65 3 5
85 4 11
25
INSTALLATION SEQUENCE
(A) (B)
Parallel arm I
nstallation
Sp
eed screws
Ri
ght hand door
Left hand door
S
R
L
S
L
R
45° 45°
BC
BC
HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 - (800) 325-9995 - Fax (800) 782-0149
HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 - (800) 325-9995 - Fax (800) 782-0149
/
