EnviroLite EV1057-281 Operating instructions

Questions, problems, missing parts? Before returning to the store,

call Envirolite Customer Service

8 a.m. – 6 p.m., EST, Monday – Friday

1-855-573-6156

EV1057-281

LED CEILING FLUSH MOUNT

SAFETY INFORMATION

 Before starting installation of this

fixture or removal of a previous

fixture, disconnect the power by

turning off the circuit breaker or by

removing the fuse at the fuse box.

 Consult a qualified electrician if you have any electrical questions or need to

replace the driver.

 If you have any non-electrical questions about this fixture, please contact our

Customer Service Team at 1-855-573-6156.

WARNING: Disconnect the

power prior to removing or

installing a light fixture.

PLANNING THE INSTALLATION

NOTE: Keep your receipt and

these instructions for Proof of

Purchase.

Read all instructions before assembly and installation. Before starting installation

of the fixture or removal of a previous fixture, disconnect the power by turning off

the circuit breaker or by removing the fuse at the fuse box. To avoid damaging

this product, assemble it on a soft, non-abrasive surface such as carpet or

cardboard.

TOOLS REQUIRED

2

Phillips

Screwdriver

Wire

Cutter

Wire

Stripper

Ladder

Safety

Goggles

Electrical

Tape

3

Part

Description

Quantity

A

Fixture Pan

1

B

Glass Shade

1

AA

Hex Nut

3

BB

Washer

1

CC

Finial

1

DD

Wire Nut

3

EE

Mounting Screw

2

FF

Fixture Screw

2

GG

Decorative Cap

1

HH

Nipple

1

II

Mounting Bracket

1

HHFF GG IIEE

BB CCAA DD

A

B

PACKAGE CONTENTS (not to scale)

INSTALLATION

1

 Thread the mounting screws (EE)

through the mounting bracket (II)

and into the outlet box.

 Thread the fixture screws (FF) so

that they extend approximately 1/2

in. below the ceiling.

2

 Pull the power supply wires out

from the outlet box.

 Attach the black supply wire to the

black fixture wire using wire nuts

(DD).

 Attach the white supply wire to the

white fixture wire using wire nuts

(DD).

 Connect the fixture ground wire

and the supply ground wire

together using a wire nut (DD).

 Wrap all wire connections with

electrical tape for a more secure

connection.

4

NOTE: If you have electrical

questions consult your local

electrical code for approved

grounding methods.

EE

FF

II

DD

FF

A

II

INSTALLATION (continued)

3

 Carefully tuck all the wires and wire

connections into the outlet box.

 Place the fixture pan (A) over the

outlet box and feed the fixture

screws (FF) through the keyhole

slots.

 Rotate the fixture pan (A) so that

the fixture screws (FF) slide into

the narrow ends of the keyhole

slots.

 Tighten the fixture screws (FF) so

that the fixture pan (A) is secured

flush against the ceiling.

4

 Thread a hex nut (AA) onto the

nipple (HH) about a quarter of the

way down.

 Insert the nipple (HH) through the

center hole in the fixture pan (A)

bracket and secure the nipple (HH)

with a hex nut (AA).

 Slide the glass shade (B) over the

nipple (HH), then slide the washer

(BB) over the nipple (HH).

 Secure the glass shade (B) in place

using a hex nut (AA).

 Slide the decorative cap (GG) over

the nipple (HH) and secure the

decorative cap (GG) in place using

the finial (CC).

5

A

FF

A

B

HH

BB

GG

AA

CC

AA

Bottom

View

A FF

 Turn on power at the circuit breaker or fuse box.

 Turn the light switch on to activate the fixture.

OPERATION

NOTE: Do not use any cleaners

with chemicals, solvents, or harsh

abrasives. Use only a dry soft

cloth to dust or wipe carefully.

EXTERIOR MAINTENANCE

 Use a dry or slightly dampened

clean cloth and wipe the surface

of the fixture.

INTERIOR MAINTENANCE

 Disconnect power to the fixture by turning off the circuit breaker or by

removing the fuse at the fuse box.

 Use a dry or slightly dampened clean cloth to wipe the interior surface of the

fixture.

CARE & CLEANING

DRIVER REPLACEMENT

6

 This product is ENERGY STAR ® listed. Please contact a qualified

electrician if driver replacement is needed.

Constant Current LED Driver & Triac Dimmer

P/N: JY20W0600-33-TD

Vin: 100-135VAC 50-60Hz

lin: 0.4A Max

Vout: 24-33VDC

lout: 600mA C.C.

Max Pout: 20W

PF: > 0.92

L=BLACK

N=WHITE

AC INPUT

+ =RED

– =YELLOW

DC OUTPUT

Made in China

E 358430

JWY

Blanc Rouge

Noir Jaune

Class 2 Bloc d’alimentacion | Endoit Sec ou Humide

ATTENTION

DÉCONNECTER LA TENSION DE LA LIGNE AVANT

L'INSTALLATION OU LE REMPLACEMENT.

VEL19060120HDA-1

Entrée: 23 W, 0.23 A

Sortie: 24-34V, 600 mA

FP: >0.90

COURANT CONSTANT

Conducteur DEL Dimmable

120V 60Hz

RoHS

E339538

Santa Fe Springs, CA

www.espentech.com

V2 Sans Frais 1-866-933-7736 Made in China

N +

L -

Blanco Rojo

Negro Amarillo

Clase 2 Fuente de Alimentación | Lugares secos o Húmedos

PRECAUCIÓN

DESCONECTE VOLTAJE DE LÍNEA ANTES DE

INSTALAR O REEMPLAZAR

VEL19060120HDA-1

Entrada: 23 W, 0.23A

Salida: 24-34 V, 600 mA

Factor de Potencia: >0.90

CORRIENTE CONSTANTE

Conductor LED Regulable

120V 60Hz

RoHS

E339538

Santa Fe Springs, CA

www.espentech.com

V2 Sin Cargo 1-866-933-7736 Hecho en China

N +

L -

Class 2 Power Supply | Dry or Damp Location

CAUTION

DISCONNECT LINE VOLTAGE BEFORE INSTALLING OR

REPLACING

VEL19060120HDA-1

In: 23W, 0.23A

Out: 24-34V, 600mA

PF: >0.90

CONSTANT CURRENT

Dimmable LED Driver

120V 60Hz

RoHS

E339538

Santa Fe Springs, CA

www.espentech.com

V2 Toll Free 1-866-933-7736 Made in China

W Red

B Yel

N +

L -

7

For an up-to-date list of compatible dimmers, visit envirolite-LED.com.

DIMMING

FCC NOTICE

This device has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications. However, there is no

guarantee that interference can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interface by one or more of the

following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the device and receiver.

 Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

Problem

Solution

The light will not turn on.

 Make sure the power supply is on.

 Test or replace the switch.

 Check the wiring.

 Replace the driver.

The fuse blows or circuit breaker

trips when light is turned on.

 Check the wire connections.

TROUBLESHOOTING

WARRANTY

8

WHAT IS COVERED

The manufacturer warrants this lighting fixture to be free from defects in materials

and workmanship for a period of five (5) years from date of purchase. This

warranty applies only to the original consumer purchaser and only to products

used in normal use and service. If this product is found to be defective, the

manufacturer’s only obligation, and your exclusive remedy, is the repair or

replacement of the product at the manufacturer’s discretion, provided that the

product has not been damaged through misuse, abuse, accident, modifications,

alterations, neglect or mishandling.

WHAT IS NOT COVERED

This warranty shall not apply to any product that is found to have been improperly

installed, set-up, or used in any way not in accordance with the instructions

supplied with the product. This warranty shall not apply to a failure of the product

as a result of an accident, misuse, abuse, negligence, alteration, or faulty

installation, or any other failure not relating to faulty material or workmanship.

This warranty shall not apply to the finish on any portion of the product, such as

surface and/or weathering, as this is considered normal wear and tear.

The manufacturer does not warrant and specially disclaims any warranty, whether

expressed or implied, of fitness for a particular purpose, other than the warranty

contained herein. The manufacturer specifically disclaims any liability and shall

not be liable for any consequential or incidental loss or damage, including but not

limited to any labor/expense costs involved in the replacement or repair of said

product.

Page is loading ...

 Conecte la alimentación en el disyuntor o caja de fusibles.

 Gire el interruptor de la luz para activar el aparato.

OPERACIÓN

MANTENIMIENTO DEL EXTERIOR

 Use un paño limpio y seco o

ligeramente humedecido y

limpie la superficie de la

luminaria.

MANTENIMIENTO DEL INTERIOR

 Apague la potencia a la linterna de manera de desconectando el disyuntor o

quitando el fusible en la caja de fusibles.

 Use un paño limpio y seco o ligeramente humedecido y limpie la superficie

de la linterna.

CUIDADO Y LIMPIEZA

REEMPLAZO DEL CONTROLADOR

NOTA: No use limpiadores

con químicos, solventes o

abrasivos fuertes. Use sólo un

paño seco para sacudir o

limpiar con cuidado.

14

 Este producto esta en la lista de ENERGY STAR®. Por favor, póngase en

contacto con un electricista calificado si el reemplazo del conductor es

necesario.

Controlador LED con corriente constante

P/N: JY20W0600-33-TD

Vin: 100-135VAC 50-60Hz

Iin: 0.4A Max

Vout: 24-33VDC

Iout: 600mA C.C.

Max Pout: 20W

PF: > 0.92

L=NEGRO

N=BLANCO

ENTRADA AC

+ =ROJO

– =AMARILLO

SLAIDA DC

Hecho en China

E 358430

JWY

Blanc Rouge

Noir Jaune

Class 2 Bloc d’alimentacion | Endoit Sec ou Humide

ATTENTION

DÉCONNECTER LA TENSION DE LA LIGNE AVANT

L'INSTALLATION OU LE REMPLACEMENT.

VEL19060120HDA-1

Entrée: 23 W, 0.23 A

Sortie: 24-34V, 600 mA

FP: >0.90

COURANT CONSTANT

Conducteur DEL Dimmable

120V 60Hz

RoHS

E339538

Santa Fe Springs, CA

www.espentech.com

V2 Sans Frais 1-866-933-7736 Made in China

N +

L -

Blanco Rojo

Negro Amarillo

Clase 2 Fuente de Alimentación | Lugares secos o Húmedos

PRECAUCIÓN

DESCONECTE VOLTAJE DE LÍNEA ANTES DE

INSTALAR O REEMPLAZAR

VEL19060120HDA-1

Entrada: 23 W, 0.23A

Salida: 24-34 V, 600 mA

Factor de Potencia: >0.90

CORRIENTE CONSTANTE

Conductor LED Regulable

120V 60Hz

RoHS

E339538

Santa Fe Springs, CA

www.espentech.com

V2 Sin Cargo 1-866-933-7736 Hecho en China

N +

L -

Class 2 Power Supply | Dry or Damp Location

CAUTION

DISCONNECT LINE VOLTAGE BEFORE INSTALLING OR

REPLACING

VEL19060120HDA-1

In: 23W, 0.23A

Out: 24-34V, 600mA

PF: >0.90

CONSTANT CURRENT

Dimmable LED Driver

120V 60Hz

RoHS

E339538

Santa Fe Springs, CA

www.espentech.com

V2 Toll Free 1-866-933-7736 Made in China

W Red

B Yel

N +

L -

Page is loading ...

EnviroLite EV1057-281 Operating instructions

EnviroLite EV1057-281 Operating instructions

in other languages

Related papers

Other documents