Rockwell Automation Allen-Bradley VersaView 6300T User manual

Brand: Rockwell Automation

Model: Allen-Bradley VersaView 6300T

Type: User manual

This manual is also suitable for

VersaView 6300B Box PCs and

6300T Box Thin Clients

Bulletin Numbers 6300B-BMAx and 6300T-BAx1

User Manual

Original Instructions

2 Rockwell Automation Publication 6300B-UM001A-EN-P - July 2020

VersaView 6300B Box PCs and 6300T Box Thin Clients User Manual

Important User Information

Read this document and the documents listed in the additional resources section about installation, configuration, and

operation of this equipment before you install, configure, operate, or maintain this product. Users are required to familiarize

themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws, and standards.

Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to

be carried out by suitably trained personnel in accordance with applicable code of practice.

If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be

impaired.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the use

or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and

requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for

actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software

described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc., is

prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

Labels may also be on or inside the equipment to provide specific precautions.

WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous environment, which may

lead to personal injury or death, property damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property damage, or

economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the consequence.

IMPORTANT Identifies information that is critical for successful application and understanding of the product.

SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerous voltage may

be present.

BURN HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that surfaces may reach

dangerous temperatures.

ARC FLASH HAZARD: Labels may be on or inside the equipment, for example, a motor control center, to alert people to potential Arc

Flash. Arc Flash will cause severe injury or death. Wear proper Personal Protective Equipment (PPE). Follow ALL Regulatory requirements

for safe work practices and for Personal Protective Equipment (PPE).

Rockwell Automation Publication 6300B-UM001A-EN-P - July 2020 3

VersaView 6300B Box PCs and 6300T Box Thin Clients User Manual

Safety Guidelines

The VersaView® 6300B box PCs and 6300T box thin clients in this publication

can be operated only by qualified personnel. Qualified personnel are those

who, based on their training and experience, are able to identify risks and

potential hazards while working with these computers.

The VersaView 6300B box PCs and 6300T box thin clients are meant only for

indoor use. The computers can be damaged if operated outdoors.

The VersaView 6300B box PCs and 6300T box thin clients are open equipment,

which means the following:

• This equipment can only be integrated in housings or cabinets where

the computer is operated from the front panel.

• The housing or cabinet in which the computer is mounted can only be

accessed with a key or tool, and only by qualified personnel.

• Before a housing or cabinet can be opened, all power must first be

disconnected.

Proper Disposal of the

Computer

You cannot dispose of computer equipment like other waste material. Most

computers and monitors contain heavy metals that can contaminate the earth.

Therefore, check with local health and sanitation agencies for ways to dispose

of computer equipment safely.

Battery Removal

Waste Electrical and Electronic Equipment (WEEE)

This computer contains a sealed lithium battery that could need replacement during the life

of the computer. At the end of its life, collect the battery that is contained in this computer

separately from any unsorted municipal waste.

At the end of life, this equipment should be collected separately from any unsorted municipal

waste.

4 Rockwell Automation Publication 6300B-UM001A-EN-P - July 2020

VersaView 6300B Box PCs and 6300T Box Thin Clients User Manual

Notes:

Rockwell Automation Publication 6300B-UM001A-EN-P - July 2020 5

Table of Contents

Safety Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Proper Disposal of the Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Catalog Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Additional Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Chapter 1

About the Box PC and Box Thin

Client

Computer Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Computer Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Chapter 2

Install the Box PC or Box Thin

Client

Unpack the Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Prepare for Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Environment and Enclosure Information . . . . . . . . . . . . . . . . . . . . . . 11

UL/cUL Mark Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

European Union Directive Compliance . . . . . . . . . . . . . . . . . . . . . . . . 12

Installation Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Mounting Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Required Tools and Hardware for Installation . . . . . . . . . . . . . . . . . . . . . 13

Install the Box PC or

Box Thin Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Connect Peripheral Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Grounding and Bonding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

DC Power Supply Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Connect DC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Install the Ground Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Install the Factory-supplied DC Power Connector Assembly . . . . . 16

Chapter 3

Operate the Box PC or Thin

Client

Operating Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Start the Box PC or Box Thin Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

LED and Button Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Restart or Reset the VersaView 6300B Box PC. . . . . . . . . . . . . . . . . . . . . . 18

Restart the VersaView 6300B Box PC . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Reset the VersaView 6300B Box PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Shut Down the VersaView 6300B Box PC . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Chapter 4

Configure the UEFI (BIOS)

Settings

Access the Set-up Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Common Set-up Modifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Upgrade to a New UEFI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

6 Rockwell Automation Publication 6300B-UM001A-EN-P - July 2020

Chapter 5

Clean the Box PC and Box Thin

Client

Clean the Vent Holes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Chapter 6

Troubleshoot the System Thermal Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Load the System Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Ship or Transport the Computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Chapter 7

Replace Components Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Voltage Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Electrostatic Discharge Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Pre-configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Post-configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Remove the Cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Replace the Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Reinstall the Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Rockwell Automation Publication 6300B-UM001A-EN-P - July 2020 7

Preface

This manual is a user guide for VersaView® 6300B box PCs and 6300T box thin

clients. It provides procedures to the following:

• Install the computer.

• Make computer connections.

• Operate the computer.

• Troubleshoot the computer.

A general knowledge of automation technology is needed to understand and

follow the instructions in this publication.

Knowledge of personal computers and Microsoft Windows® operating

systems

(1)

are required to understand and follow the instructions in this

publication.

Catalog Numbers

This publication is applicable to these VersaView box PCs and box thin clients.

For your catalog number, see the product label on the side of your computer.

Additional Resources

These documents contain additional information about related products from

Rockwell Automation.

You can view or download publications at rok.auto/literature

(1) VersaView 6300T thin clients do not operate with Microsoft Windows operating systems.

VersaView box PCs with Microsoft Windows® operating systems 6300B-BMAx

VersaView box thin clients optimized for server-based operation 6300T-BAx1

Resource Description

VersaView 6300B Box PCs and 6300T Box Thin Client

Installation Instructions, publication 6300B-IN001

Provides basic installation guidelines and instructions for

VersaView 6300B box PCs and 6300T box thin clients.

VersaView 6300 Industrial Computer and Monitor

Specifications Technical Data, publication IC-TD003

Provides technical specifications about all VersaView 6300

industrial PCs, thin clients, and monitors.

ThinManager® with Relevance® 11 User Manual,

publication TM-UM001

Provides instructions to define sources, deploy content,

configure devices, and user access between a server and

thin clients.

Industrial Automation Wiring and Grounding

Guidelines, publication 1770-4.1

Provides general guidelines for installing a Rockwell

Automation industrial system.

Product Certifications website,

rok.auto/certifications

Provides declarations of conformity, certificates, and other

certification details.

8 Rockwell Automation Publication 6300B-UM001A-EN-P - July 2020

Preface

Notes:

Rockwell Automation Publication 6300B-UM001A-EN-P - July 2020 9

Chapter 1

About the Box PC and Box Thin Client

The Allen-Bradley® VersaView® 6300B box PCs and 6300T box thin clients have

a fanless design, which is optimal for applications that require low

maintenance. These compact PCs (Cat. Nos. 6300B-BMAx) and box thin clients

(Cat. Nos. 6300T-BAx1) feature Intel (Apollo Lake) Atom processors.

The following features are available for the VersaView 6300B box PCs

and 6300T box thin clients:

• For the 6300B box PCs, available with Microsoft Windows® 10 IoT

Enterprise 2019 LTSC

(1)

• For the 6300T box thin clients, they are ThinManager® ready

• For the 6300B box PCs, SSD storage (no drives in 6300T box thin

clients)

• One DisplayPort video output supports up to 4K high resolution

• 2 x Ethernet and 2 x USB 3.0 (Type A) ports

• 24V DC input power

(1) 6300B box PCs are ThinManager compatible.

10 Rockwell Automation Publication 6300B-UM001A-EN-P - July 2020

Chapter 1 About the Box PC and Box Thin Client

Computer Dimensions

Figure 1 shows the dimensions of the VersaView 6300B box PCs and 6300T thin

clients. All dimensions are in mm (in.).

Figure 1 - VersaView 6300B and 6300T Dimensions

Computer Connections

Figure 2 show the hardware features and peripheral connections of VersaView

6300B box PCs and 6300T thin clients.

Figure 2 - VersaView 6300B-BABx and 6300T-BAx1 Peripheral Connections

39.4

(1.55)

4.5

(0.18)

135.5

(5.02)

100

(3.94)

20 (0.79)

101.5 (4)

20 (0.79)

Ø 4.5

(Ø 0.18)

Ø 9

(Ø 0.35)

Ø 4.5

(Ø 0.18)

(0.31)

36 (1.42)

7.5

(0.3)

8 (0.31)

No. Description

1 24V DC power input connection

2 2 x Ethernet LAN port

3 2 x USB 3.0 (Type A) port

4 DisplayPort video output

5 Ground (earth) screw

Rockwell Automation Publication 6300B-UM001A-EN-P - July 2020 11

Chapter 2

Install the Box PC or Box Thin Client

Follow these guidelines and procedures to help you plan your installation, and

mount and power up the VersaView® 6300B box PC or 6300T box thin client.

Unpack the Computer

Before you unpack the computer, inspect the shipping carton for damage. If

damage is visible, immediately contact the shipper and request assistance.

Otherwise, proceed with unpacking.

Keep the original packing material in case you must return the computer for

repair or transport it to another location.

Parts List

The box PC or box thin client ship with the following items.

Prepare for Installation

Read and follow these precautions to install the box PC or box thin client.

Environment and Enclosure Information

Item Description

Hardware

• Factory installed mounting bracket

• DC power connector assembly kit

Document

VersaView 6300B Box PC and 6300T Box Thin Clients Installation Instructions, publication

6300B-IN001

ATTENTION: This equipment is intended for use in a Pollution Degree 2 industrial

environment, in overvoltage Category II applications (as defined in IEC 60664-1), at

altitudes up to 2000 m (6561 ft) without derating.

This equipment is considered Group 1, Class A industrial equipment according to

IEC/EN 61326-1. Without appropriate precautions, there can be potential difficulties

with electromagnetic compatibility in other environments due to conducted as well

as radiated disturbance.

This equipment is considered open equipment, which means it must be mounted in

an enclosure where the equipment can be operated from the front panel.

The enclosure in which this equipment is installed must be accessed only with a key

or tool, and only by trained and authorized personnel.

In addition to this publication, see the following:

• Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1

, for

more installation requirements

• UL 50, CSA C22.2 No. 94.1, and IEC 60529, as applicable, for explanations of the

degrees of protection provided by enclosures

12 Rockwell Automation Publication 6300B-UM001A-EN-P - July 2020

Chapter 2 Install the Box PC or Box Thin Client

UL/cUL Mark Compliance

Equipment with the UL/cUL mark complies with the requirements of

UL 61010-1, UL 61010-2-201, CSA C22.2 No. 61010-1, and CSA C22.2

No. 61010-2-201. A copy of the certificate of compliance is available at

rok.auto/certifications

European Union Directive Compliance

This computer meets the European Union Directive requirements when

installed within the European Union or EEA regions and have the CE marking.

A copy of the declaration of the conformity is available at

rok.auto/certifications

Connect peripheral cables to the appropriate I/O ports on the computer. To

comply with EN 61326-1, see Connect Peripheral Cables

on page 14 for the

required cable types.

Installation Guidelines

Follow these guidelines to make sure that your computer provides service with

excellent reliability.

• When choosing the installation site, consider the following:

- The site must have sufficient power

- The site must be indoors

- The site must not expose the computer to direct sunlight

• The computers can operate in the following surrounding air

temperature ranges.

- 0…55 °C (32…131 °F) with the Intel Atom x5 processor

- 0…50 °C (32…122 °F) with the Intel Atom x7 processor

The surrounding air temperature must not exceed the maximum

temperature for your computer, especially when the computer is

mounted in an enclosure.

• The computers can be stored in a surrounding air temperature range of

-10…+60 °C (14…140 °F).

• The humidity of the ambient air must not exceed 80% noncondensing.

ATTENTION: This equipment is intended to operate in an industrial or control room

environment, which uses some form of power isolation from the public low-voltage

mains. Obtain permission from the local power authority before you connect any

computer configuration that draws more than 75 W of AC power directly from the

public mains.

All I/O cables must be used only indoors.

Rockwell Automation Publication 6300B-UM001A-EN-P - July 2020 13

Chapter 2 Install the Box PC or Box Thin Client

Mounting Requirements

Follow these requirements to mount the box PC or thin client.

• Choose a suitable mounting height

• Only mount the computer in a horizontal orientation and vertical

(upright) position for the following:

- Mount the factory-installed bracket so the I/O ports face forward

and the ground screw is at the bottom

• Mount the computer so there is at least 20 mm (0.8 in.) of clearance on

each side for the circulation necessary for cooling

Required Tools and

Hardware for Installation

The following tools and hardware are needed for book mount installations.

• Drill and drill bit

• 2.5 mm Phillips screwdriver

• Four M4x20 stainless steel screws (customer supplied)

• Safety glasses

Install the Box PC or

Box Thin Client

VersaView 6300B box PCs and VersaView 6300T thin clients are shipped with

book mount brackets that are factory-installed.

To mount the computer, perform the following steps.

1. Use the dimensions in Figure 1 on page 10

to locate and drill holes for

the four M4x20 stainless steel screws.

2. Install the four customer-supplied screws but leave enough space to

hang the brackets.

3. Align the keyhole slots on the top bracket with the top two screws.

4. Align the slots on the bottom bracket with the bottom two screws.

5. Slide the computer downward until all four screws are at the top of each

bracket slot.

6. Tighten the four screws.

0°

14 Rockwell Automation Publication 6300B-UM001A-EN-P - July 2020

Chapter 2 Install the Box PC or Box Thin Client

Connect Peripheral Cables

Connect peripheral cables to the appropriate I/O ports on the computer. For

available connections, see Figure 2 on page 10

To comply with EN 61326-1, use the following for cable types. All I/O cables

must be used only indoors, and USB cables must be less than 3 m (9.84 ft) long.

Grounding and Bonding

Whenever two connected pieces of equipment are far apart, it is possible that

their ground connections could be at different potential levels.

To overcome these possible spikes, the following bonding methods can help

prevent electrical energizing by routing voltage spikes safely to earth ground:

• Method 1: Connect the data cable shields to the equipotential bonding

rail on both sides before you connect the cable to the interfaces.

• Method 2: Use an equipotential bonding cable (16 mm

or 6 AWG) to

connect the grounds between this VersaView 6300B box PC or 6300T

thin client and a connected monitor.

DC Power Supply Guidelines

Follow these guidelines to select the DC power supply for the computer.

• The computer must be powered with a voltage of 24V DC (18…32V DC

input voltage range).

• The nominal output power should be 25% larger than the drained

power.

• The output voltage rise time has to be less than 100 ms.

• Consider the working temperature and the thermal derating of the

power supply.

• The inrush current can be represented by the following figure, where

the peak current is 10 A and the pulse width time is 400 μs:

Cable Type Required Attribute Cable Type Required Attribute

LAN

Shielded

DVI-D

Shielded

USB (2.0 and 3.0) DisplayPort

Serial RS-232 DC power Unshielded

Current

Peak Current

Inrush Current Magnitude

Steady-state Current Value

Time

Pulse Width

Rockwell Automation Publication 6300B-UM001A-EN-P - July 2020 15

Chapter 2 Install the Box PC or Box Thin Client

Connect DC Power

Operate the box PC or box thin client in an industrial or control room

environment, which uses some form of power isolation from the public,

low-voltage mains.

All VersaView DC powered models require a safety extra low voltage (SELV)

(1)

power supply per UL. The power supply is internally protected against reverse

polarity.

To minimize ground loop currents and noise, Allen-Bradley recommends that

DC powered models use only one grounded connection. See Install the Ground

Wire for the ground connection on these models.

Follow these steps to connect the computer to a DC power source.

Install the Ground Wire

1. Turn off the main power switch or breaker.

2. Remove the supplied nut, eyelet terminal, and washers from the

ground screw.

3. For earth ground, fasten a 2.5 mm

(14 AWG) or larger external wire to

the eyelet terminal.

Use a ground wire with an insulation color that is approved by local

inspection authority.

4. Install the ground wire to the ground screw in the following sequence.

5. Tighten the nut to the ground screw.

ATTENTION: When you connect power to the thin client or computer for the first

time, these actions occur:

• The default UEFI setting automatically starts the computer after it is plugged into a

power source.

• For VersaView 6300B box PCs with a Microsoft Windows operating system (OS), you

must read and accept an End User Setup procedure.

Do not disconnect power from the system until after the Windows Setup

procedure is completed. If power is disconnected during this procedure, it can

result in a corrupted system image.

ATTENTION: For VersaView 6300B box PCs with a Windows OS, perform the

following:

• Supply the computer with its own disconnect. Use an uninterruptible power source

(UPS) to help protect against unexpected power failure or power surges.

• Always shut down the Windows OS before you disconnect power to the computer to

minimize performance degradation and operating system failures.

(1) Where SELV is as defined in IEC 61010-2-201.

You need the following tools for this installation:

• Small screwdriver

• Wire stripper, cutter, and crimper tool

• Cutting pliers

12345

Sequence

No. Description

Sequence

No. Description

1 Toothed washer 4 Lock washer

2 Eyelet terminal 5 Nut

3Washer

16 Rockwell Automation Publication 6300B-UM001A-EN-P - July 2020

Chapter 2 Install the Box PC or Box Thin Client

Install the Factory-supplied DC Power Connector Assembly

1. Verify that the DC power wires meet these requirements:

• Material: Stranded copper

• Wire gauge: 1.5…4 mm

(16…12 AWG)

2. Open the power connector assembly kit that shipped with the computer

(A).

3. Insert the cable tie through the slots of the appropriate connector

clamp (B).

4. Slide the connector clamp with the attached tie on the end of the

supplied DC terminal block (C).

5. Insert the DC terminal wires into the supplied DC terminal block to

match what is shown in (C).

Use external wires that are at least 1.5 mm

(16 AWG) gauge.

6. To secure the DC power wires to the DC terminal block, tighten and

torque the terminal block screws between 0.22…0.25 N•m

(1.95…2.21 lb•in).

7. Tighten the cable tie so it is snug against the terminal wires (D).

8. Use cutting pliers to cut the excess part (E).

9. Install the white label supplied with the kit (F).

10. Align and install the other connector clamp half to complete the

assembly (G).

11. Install the assembled power connector to the computer (H).

Tighten each screw to secure the power connector to the computer.

12. Turn on the main power switch or breaker.

DC Terminal Block

–

Rockwell Automation Publication 6300B-UM001A-EN-P - July 2020 17

Chapter 3

Operate the Box PC or Thin Client

Operating Guidelines

Follow these operating guidelines for your VersaView® 6300B box PC or 6300T

thin client.

• When the box PC or box thin client is mounted in an enclosure, ke

the enclosure door closed during operation so d

ust and ot

her airborne

contamination do not infiltrate the thin client or computer. Open the

doo

r only for routine maintenance.

• For box PCs with a Microsoft Window

s® operating system (OS), always

use the proper power down procedures as required, such as the Shut

Down command in

the Windows OS.

• After you shut down the box

PC or box thin client, do not apply power

ain until shutdown is complete.

Start the Box PC or Box Thin

Client

Follow these steps to start your VersaView 6300B box PC or 6300T thin client.

1. Make sure that all necessary peri

pheral devices are connected to the

corresponding I/O ports on the box PC or box thin client.

2. Make sure any connected components with separate power suppl

ies

(such as an externa

l display) are turned on first.

3. To power on the box PC or box thin client, press the sy

stem or power

reset

button on the front panel. For button locations, see Table 1

page 18.

LED and Button

Descriptions

After a VersaView 6300B box PC or 6300T thin client is powered on, various

light-emitting diodes (LEDs) monitor its state. Use these LEDs to determine if

they are lit and what color they emit.

There are also buttons on the computer to reset computer states that are

monitored by the LEDs.

IMPORTANT The following steps apply to when the thin client or computer must be

started manually, and DC power has been connected already.

See Connect DC Power on page 15 for when power is applied to the box PC or

box thin client for the first time.

18 Rockwell Automation Publication 6300B-UM001A-EN-P - July 2020

Chapter 3 Operate the Box PC or Thin Client

The following tables detail what LEDs and buttons are on each box PC and box

thin client.

Prepar e for Installati on

Restart or Reset the

VersaView 6300B Box PC

Restart the VersaView 6300B Box PC

Use either of the following methods to restart the box PC.

• From the Start menu, click or choose Restart.

• Press Ctrl+Alt+Delete, and then click or choose Restart.

During a restart, the box PC does the following:

•Clears the RAM.

• Starts the POST.

• Initializes peripheral devices.

• Loads the Windows OS.

Table 1 - LEDs and Buttons on the Front Panel of VersaView 6300B-BMAx Box PCs and VersaView 6300T-BAx1 Box Thin Clients

No. Description Color Function

1 Standby/power on LED

No color The computer is powered off.

Green The computer is powered on.

Yellow

The computer is safe to power off; the operating system has been

shut down successfully.

(1)

Flashing green

The system is in a low power state, and current session information

is being stored in the RAM.

2 Mass storage LED Yellow

When lit, access to a mass storage device (HDD, SSD, or CF) is

happening through a SATA channel.

3 Watchdog error LED Red When lit, the watchdog timer has expired.

Thermal alarm/

low battery LED

Red

A thermal sensor on the motherboard near the CPU has exceeded the

thermal limit of 85 °C (185 °F).

Flashing red

The clock battery power is below 2.5V and should be replaced. At 2V,

data and time loss is possible.

5 Power/system reset button —

For the main reset of the system. Press this button once to restart

the computer and reset the system state.

6 Watchdog reset button — Press this button once to reset the watchdog error LED.

(1) Microsoft Windows® operating systems are not installed on VersaView 6300T thin client models.

Table 2 - LAN LEDs on the Front Panel of VersaView 6300B-BMAx Box PCs and VersaView 6300T-BAx1 Box Thin Clients

No. Description Color Function

Data link

No color No data link is present.

Green Data link is established.

Flashing green Data link is established and there is data transfer.

2 Data speed

No color 10 Mbps

Green 100 Mbps

Yellow 1000 Mbps (1 Gbps)

IMPORTANT The instructions in this section are only for VersaView 6300B box PCs with

Windows operating systems.

VersaView 6300T thin clients can be restarted or reset through the

ThinManager® software on the server. For more information, see the

ThinManager with Relevance® 11 User Manual, publication TM-UM001

IMPORTANT A connected keyboard, mouse, and display are needed for some of the

following steps.

Rockwell Automation Publication 6300B-UM001A-EN-P - July 2020 19

Chapter 3 Operate the Box PC or Thin Client

Use a connected display to view the progress of the POST, initializing of any

peripheral devices, and the startup dialogs for any installed Windows OS.

Reset the VersaView 6300B Box PC

Use this method when power has been interrupted temporarily, and the box

PC is unresponsive when power returns.

If methods to restart the box PC are unsuccessful, then press the system reset

button on the front panel of the box PC.

For the system reset button location, see Table 1 on page 18

Shut Down the VersaView

6300B Box PC

Use either of the following methods to shut down the box PC.

• From the Start menu, click or choose Shut Down.

• Press Ctrl+Alt+Delete, and then click or choose Shut Down.

IMPORTANT Use this method only if there are no better options, like keyboard or mouse

commands. System reset can cause data loss and possible corruption to the

operating system.

IMPORTANT The instructions in this section are only for VersaView 6300B box PCs with

Windows operating systems.

VersaView 6300T thin clients can be shut down through the ThinManager

software on the server. For more information, see the ThinManager with

Relevance 11 User Manual, publication TM-UM001

IMPORTANT A connected keyboard, mouse, and display are needed for the following

steps.

20 Rockwell Automation Publication 6300B-UM001A-EN-P - July 2020

Chapter 3 Operate the Box PC or Thin Client

Notes:

Page is loading ...

Rockwell Automation Allen-Bradley VersaView 6300T User manual

Brand: Rockwell Automation

Model: Allen-Bradley VersaView 6300T

Type: User manual

This manual is also suitable for

Download PDF

report

Rockwell Automation Allen-Bradley VersaView 6300T User manual

This manual is also suitable for

Rockwell Automation Allen-Bradley VersaView 6300T User manual

Related papers

Other documents