Allen-Bradley VersaView 6186-M User manual

VersaView 6186-M

Industrial Flat

Panel Monitors

1200M, 1500M, 1700M, 2000M

User Manual

Allen-Bradley Spares

Important User Information

Solid state equipment has operational characteristics differing from those of

electromechanical equipment. Safety Guidelines for the Application,

Installation and Maintenance of Solid State Controls (Publication SGI-1.1

available from your local Rockwell Automation sales office or online at

http://www.ab.com/manuals/gi) describes some important differences

between solid state equipment and hard-wired electromechanical devices.

Because of this difference, and also because of the wide variety of uses for

solid state equipment, all persons responsible for applying this equipment

must satisfy themselves that each intended application of this equipment is

acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for

indirect or consequential damages resulting from the use or application of

this equipment.

The examples and diagrams in this manual are included solely for illustrative

purposes. Because of the many variables and requirements associated with

any particular installation, Rockwell Automation, Inc. cannot assume

responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to

use of information, circuits, equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without

written permission of Rockwell Automation, Inc. is prohibited.

Throughout this manual we use notes to make you aware of safety

considerations.

WARNING

Identifies information about practices or circumstances

that can cause an explosion in a hazardous environment,

which may lead to personal injury or death, property

damage, or economic loss.

IMPORTANT

Identifies information that is critical for successful

application and understanding of the product.

ATTENTION

Identifies information about practices or circumstances

that can lead to personal injury or death, property

damage, or economic loss. Attentions help you:

• identify a hazard

• avoid a hazard

• recognize the consequence

SHOCK HAZARD

Labels may be located on or inside the drive to alert

people that dangerous voltage may be present.

BURN HAZARD

Labels may be located on or inside the drive to alert

people that surfaces may be dangerous temperatures.

1 Publication 6186M-UM001D-EN-P

Table of Contents

Preface

Who Should Use This Manual . . . . . . . . . . . . . . . . . . Preface-1

Purpose of This Manual. . . . . . . . . . . . . . . . . . . . . . . Preface-1

Contents of This Manual . . . . . . . . . . . . . . . . . . . . . . Preface-2

Manual Conventions . . . . . . . . . . . . . . . . . . . . . . . . . Preface-3

Allen-Bradley Support . . . . . . . . . . . . . . . . . . . . . . . . Preface-3

Chapter 1

System Features

Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Part Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Chapter 2

Installation

Before Unpacking the Monitor. . . . . . . . . . . . . . . . . . . . . . 2-1

Hazardous Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Installation Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Enclosures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Mounting Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

VersaView 1200M Mounting Dimensions. . . . . . . . . . . . 2-4

VersaView 1500M Mounting Dimensions. . . . . . . . . . . . 2-4

VersaView 1700M Mounting Dimensions. . . . . . . . . . . . 2-5

VersaView 2000M Mounting Dimensions. . . . . . . . . . . . 2-5

Mounting Cutouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

Installing Monitor in Panel. . . . . . . . . . . . . . . . . . . . . . . . . 2-7

Mounting Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

Panel Mounting Guidelines . . . . . . . . . . . . . . . . . . . . . 2-8

Installing Panel Mount Monitor. . . . . . . . . . . . . . . . . . . 2-8

Installing Monitor in a Rack. . . . . . . . . . . . . . . . . . . . . . . . 2-10

Tools Needed for Rack Mount Installation. . . . . . . . . . . 2-10

Rack Mounting Guidelines . . . . . . . . . . . . . . . . . . . . . . 2-10

Installing Monitor Into a Rack. . . . . . . . . . . . . . . . . . . . 2-11

Installing Monitor on a Bench or Tabletop . . . . . . . . . . . . . 2-12

Tools Needed for Arm Mounting . . . . . . . . . . . . . . . . . 2-12

Bench/Tabletop Mounting Guidelines. . . . . . . . . . . . . . 2-12

Mounting Monitor on a Benchtop or Tabletop . . . . . . . 2-13

Installing Monitor on Wall . . . . . . . . . . . . . . . . . . . . . . . . . 2-14

Tools Needed for Wall Mounting . . . . . . . . . . . . . . . . . 2-14

Mounting Monitor on a Wall. . . . . . . . . . . . . . . . . . . . . 2-14

Making Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15

Monitor Connections . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15

Connecting a Host Video Source . . . . . . . . . . . . . . . . . 2-16

Connecting the Optional Touchscreen Interface . . . . . . 2-16

Connecting AC Power . . . . . . . . . . . . . . . . . . . . . . . . . 2-17

Connecting DC Power (Terminal Block, VersaView 1500M,

1700M, 2000M Only) . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18

Securing Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19

Allen-Bradley Spares

Publication 6186M-UM001D-EN-P

Table of Contents 2

Chapter 3

Configuring the Video Setup

Chapter Objective . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Setting the Monitor Type . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Checking and Changing

the Display Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Adjusting Your Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Chapter 4

Performing Routine Maintenance

Chapter Objective . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Replacing a Line Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Other Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Chapter 5

System Troubleshooting

Chapter Objective . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Self-Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Troubleshooting Solutions . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Allen-Bradley Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

Appendix A - Touchscreen Serial Interface

Appendix B - Video Cables

Appendix C - Product Specifications

1 Publication 6186M-UM001D-EN-P

Preface

Read this preface to familiarize yourself with the rest of the manual.

The preface covers the following topics:

• who should use this manual

• the purpose of the manual

• the contents of the manual

• conventions used in this manual

• Allen-Bradley support

Who Should Use This

Manual

Use this manual if you are responsible for installing, using, or

troubleshooting VersaView 6186-M Industrial Flat Panel Monitors.

Purpose of This Manual

This manual is a user guide for the VersaView 6186-M Industrial Flat

Panel Monitors. It gives an overview of the system and describes

procedures used to:

• install a 6186-M monitor in a panel or enclosure

• make connections to a 6186-M monitor

• configure a 6186-M monitor’s video setup

• troubleshoot a 6186-M monitor

Allen-Bradley Spares

Publication 6186M-UM001D-EN-P

Preface 2

Contents of This Manual

Chapter Title Contents

Preface Describes the purpose, background and

scope of this manual. Also specifies the

intended audience.

1 System Features Describes the features and capabilities of

the 6186-M monitors.

2 Installation Explains how to install a 6186-M monitor in

a panel, rack, bench/tabletop, or wall. Also,

how to connect power and external video

sources.

3 Configuiring the Video Setup Explains how to setup and configure

6186-M monitors.

4 Performing Routine

Maintenance

Describes cleaning and other maintenance.

5 System Troubleshooting Explains how to interpret and correct

problems with the 6186-M monitors.

Appendix A Touchscreen Serial Interface Describes setting up and enabling the

touchscreen for 6186-M monitors equipped

with a touchscreen interface.

Appendix B Video Cables Describes the HD-15 or DVI connector

cables you can use to connect your monitor

to the host computer.

Appendix C Product Specifications Specifications for the 6186-M monitors.

Publication 6186M-UM001D-EN-P

Preface 3

Manual Conventions

The following conventions are used throughout this manual:

• Bulleted lists such as this one provide information, not

procedural steps.

• Numbered lists provide sequential steps or hierarchical

information.

Allen-Bradley Support

Allen-Bradley offers support services worldwide, with over 75

Sales/Support Offices, 512 authorized Distributors and 260 authorized

Systems Integrators located throughout the United States, plus

Allen-Bradley representatives in every major country in the world.

Local Product Support

Contact your local Allen-Bradley representative for:

• sales and order support

• product technical training

• warranty support

• support service agreements

Technical Product Assistance

Before you contact Rockwell Automation for technical assistance,

please review the troubleshooting information contained in this

publication.

If the problem persists, call your local Rockwell Automation

representative, or contact Rockwell Automation in one of the

following ways:

Phone United

States/Canada

1.440.646.5800

Outside United

States/Canada

You can access the phone number for your

country via the Internet:

1. Go to http://www.ab.com

2. Click on Product Support

(http://support.automation.rockwell.com)

3. Under Support Centers, click on Contact

Information

Internet

⇒

1. Go to http://www.ab.com

2. Click on Product Support

(http://support.automation.rockwell.com)

Allen-Bradley Spares

Publication 6186M-UM001D-EN-P

Preface 4

1 Publication 6186M-UM001D-EN-P

Chapter

1

System Features

Description

The VersaView 6186-M Industrial Flat Panel Monitor offers the

following:

• Bright (250 nits) 16.7M color (24-bit) Active Matrix TFT display

• Video formats supported from 640x480 to 1600x1200

• Wide viewing angles

• Optional resistive and capacitive antiglare touchscreens

• One-button automatic screen setup

• Rear panel keypad with lockout feature

• NEMA Types 1, 12, 4X (indoor use only) and IP65

equivalent ratings

• 90…264V AC, 12V DC, or 24V DC input power supply

• Space efficient enclosure (<2.9 in. [74 mm] deep)

• Optional rack, bench, and wall mount adapter brackets

Package Contents

The shipping cartons contain the following items:

• Monitor

• CD containing ScreenSet Monitor Setup Utility, drivers, and

documentation

• Package of panel mounting hardware

• AC power adapter and cord

• HD-15 Video cable

• Stylus (monitors with touchscreen option only)

• RS-232 serial extension cable (monitors with touchscreen option

only)

• Cable retention tie wraps

• installation guide

Allen-Bradley Spares

Publication 6186M-UM001D-EN-P

1-2 System Features

Part Numbers

Catalog Number Display Size Bezel Touchscreen

6186-M12AL 12 inch Aluminum None

6186-M12ALTR Resistive Touch

6186-M15AL 15 inch Aluminum None

6186-M15ALTR Resistive Touch

6186-M15ALTC Capacitive Touch

6186-M15SS Stainless Steel None

6186-M15SSTR Resistive Touch

6186-M17AL 17 inch Aluminum None

6186-M17ALTR Resistive Touch

6186-M17ALTC Capacitive Touch

6186-M17SS Stainless Steel None

6186-M17SSTR Resistive Touch

6186-M20AL 20 inch Aluminum None

6186-M20ALTR Resistive Touch

6186-M20RK Rack Mount only

Aluminum

None

6186-M20RKTR Resistive Touch

6186-M20SS Stainless Steel None

6186-M20SSTR Resistive Touch

VersaView Monitor Mounting Adapters Cat. No.

1200M Rack Adapter 6189V-MRA12

1500M Rack Adapter 6189V-MRA15

1700M Rack Adapter 6189V-MRA17

Bench/Table Top Adapter (all models) 6189V-MBA

Wall Mount Adapter (all models) 6189V-MWA

6185-B to 1200M Mounting Adapter 6189V-MMA12

6185-C/6185-H to 1500M Mounting Adapter 6189V-MMA15

6185-D/6185-J to 1700M Mounting Adapter 6189V-MMA17

Mounting Clips 6189V-CLPS

VersaView Monitor Cables and Power Supplies Cat. No.

Analog Video Cable, 4.6 m (15 ft) 6189-SDNC21

Touch Screen Cable, 4.6 m (15 ft) 6189-SE2903

External AC Power Supply, 90…264V ac 6189V-MPS

External AC Power Supply DIN Rail Mounting Kit 6189V-MMAPS

Digital Video Cable, 2 m (6.5 ft) 6189V-DVICBL2

Digital Video Cable, 5 m (16.4 ft) 6189V-DVICBL5

1 Publication 6186M-UM001D-EN-P

Chapter

2

Installation

Before Unpacking the

Monitor

Before unpacking your new monitor, inspect the shipping carton for

damage. If damage is visible, immediately contact the shipper and

request assistance. Otherwise, proceed with unpacking.

Hazardous Locations

This equipment is suitable for:

• Class I, Division 2 Groups A, B, C, D

• Class II, Division 2 Groups F, G

• Class III, Division 1

• or non-hazardous locations

The following statement applies to use in hazardous locations.

The VersaView Flat Panel Monitors and AC adapter have an operating

temperature code of T4 (maximum operating temperature of 55°C or

131°F). Do not install the terminals in environments where

atmospheric gases have ignition temperature less than 55°C or 131°F.

TIP

Make sure you keep all the original packaging for

the monitor in case you need to return the monitor

for repair. Both the inner and outer packing cartons

should be used to ensure adequate protection for

any units returned for service.

WARNING

Explosion Hazard

• Substitution of components may impair

suitability for hazardous locations.

• Do not disconnect equipment unless power has

been switched off and area is known to be

non-hazardous.

• Do not connect or disconnect components

unless power has been switched off.

• All wiring must comply with N.E.C articles

501-4(b), 502-4(b), 503-3(b) as appropriate.

• Peripheral equipment must be suitable for the

location it is used in.

Allen-Bradley Spares

Publication 6186M-UM001D-EN-P

2-2 Installation

Installation Guidelines

Follow these guidelines to help ensure that the monitor provides safe

and reliable service.

• Ensure that sufficient power is available at the site.

Do not install the terminals in environments where atmospheric gases

have ignition temperature less than 55°C or 131°F.

• Ensure that sufficient space is available around air inlets and

outlets to provide the circulation necessary for cooling. Never

allow air passages to become obstructed.

• The ambient air temperature must not exceed the specified

maximum temperature. You may need a user-supplied fan, heat

exchanger, or air conditioner to meet this condition in some

installations.

• The humidity of the ambient air must not exceed specified

limits. In very dry environments, static charges build up very

readily. Proper grounding of the equipment through the AC

power cord can help reduce the likelihood of static discharges,

which may cause shocks and damage electronic components.

• Leave the monitor's enclosure or cover in place at all times

during operation. The cover provides protection against high

voltages inside the monitor and inhibits radio-frequency

emissions that might interfere with other equipment.

ATTENTION

In order to maintain an electrically safe installation, a

6186-M monitor must be connected to Earth ground

when installed. Installing 6186-M in a panel,

enclosure or rack that is already connected to Earth

ground will satisfy this requirement. Otherwise,

connect your monitor to Earth ground using a

16 AWG or larger external wire.

The ground wire should have green insulation with

a yellow stripe for easy identification.

TIP

Remember that heat rises. The temperature at the

top of an enclosure is often much higher than the

rest of the enclosure if air is not circulating.

IMPORTANT

This monitor is designed to operate at a range of

extremes. However, you should not continuously

operate the monitor at the highest end of the

specified temperature range.

While the product will operate at its highest

specified temperature, the overall life span of any

electronic device is shortened when it operates at its

highest rated temperature.

Publication 6186M-UM001D-EN-P

Installation 2-3

Enclosures

Mount the VersaView monitor in a panel or enclosure to protect the

internal circuitry. All units that are not rack-mount, ship with a

gasketed bezel to meet NEMA Type 1, 12, 4X (indoor use only) and

IEC IP65 only when mounted in a panel or enclosure with an

equivalent rating.

ATTENTION

Environment and Enclosure

This equipment is intended for use in a Pollution

Degree 2 industrial environment, in overvoltage

Category II applications (as defined in IEC

publication 60664-1), at altitudes up to 2000 meters

without derating.

This equipment is considered Group 1, Class A

industrial equipment according to IEC/CISPR

Publication 22. Without appropriate precautions,

there may be potential difficulties ensuring

electromagnetic compatibility in other environments

due to conducted, as well as radiated, disturbance.

This equipment is supplied as “open type”

equipment. It must be mounted within an enclosure

that is suitably designed for those specific

environmental conditions that will be present and

appropriately designed to prevent personal injury

resulting from accessibility to live parts. The interior

of the enclosure must be accessible only by the use

of a tool. Subsequent sections of this publication

may contain additional information regarding

specific enclosure type ratings that are required to

comply with certain product safety certifications.

See NEMA Standards publication 250 and IEC

publication 60529, as applicable, for explanations of

the degrees of protection provided by different types

of enclosure. Also, see the appropriate sections in

this publication, as well as the Allen-Bradley

publication 1770-4.1 (“Industrial Automation Wiring

and Grounding Guidelines”), for additional

installation requirements pertaining to this

equipment.

Allen-Bradley Spares

Publication 6186M-UM001D-EN-P

2-4 Installation

Mounting Dimensions

The following illustrations show the mounting dimensions for the

VersaView 6186-M Industrial Flat Panel Monitor. All measurements are

in mm [inches].

VersaView 1200M Mounting Dimensions

VersaView 1500M Mounting Dimensions

Mounting clip slots for panel mounting

(see page 2-8 for details)

224.0 [8.82]

110.0 [4.33]

31.2 [1.23]

56.10 [2.21]

110.0 [4.33]

340.0 [13.39]

260.0 [10.24]

235.0 [9.25]

315.0 [12.40]

8.0 [0.31]

56.1 [2.21]

Mounting clip slots for

panel mounting

(see page 2-8 for details)

410.00 [16.14]

383.6 [15.10]

281.9 [11.10]

160.0 [6.30]

58.0 [2.28]

29.5 [1.16]

309.0 [12.2]

140.0 [5.51]

282.6 [11.13]

8.0 [0.31]

58.0 [2.28]

Publication 6186M-UM001D-EN-P

Installation 2-5

VersaView 1700M Mounting Dimensions

VersaView 2000M Mounting Dimensions

Mounting clip slots for panel

mounting (see page 2-8 for details)

326.0 [12.84]

422.0 [16.61]

150.00 [5.91]150.00 [5.91]

54.8 [2.16]

30.2 [1.19]

452.0 [17.80]

356.0 [14.02]

8.0 [0.31]

54.8 [2.16]

160.0 [6.30]

328.0 [12.91]

447 [17.6]

116 [4.57]

319.3 [12.57]

116 [4.57]110 [4.33]

483 [19.0]

17.8 [0.685]

74 [2.9]

399 [15.7]]

362 [14.25]

120 [4.72]

Mounting clip slots for

panel mounting

(see page 2-8 for details)

34.6 [1.36]

Allen-Bradley Spares

Publication 6186M-UM001D-EN-P

2-6 Installation

Mounting Cutouts

The following figure provides the dimensions for making a panel or

enclosure cutout for the VersaView 6186-M Industrial Flat Panel

Monitor. All measurements are in mm [inches].

Conversion

Adapters

Description

6189V-MMA12 Mounting adapter for converting from 6185-B to 1200M

6189V-MMA15 Mounting adapter for converting from 6185-C or J to 1500M

6189V-MMA17 Mounting adapter for converting from 6185-H or D to 1700M

VersaView 1200M Monitor

VersaView 1500M Monitor

VersaView 1700M Monitor

324.0 [12.76]

386.6 [15.22]

424.0 [16.69]

254.0 [10.0]

285.6 [11.24]

329.5 [12.97]

VersaView 2000M Monitor

449.6 [17.70]

363.5 [14.31]

Publication 6186M-UM001D-EN-P

Installation 2-7

Installing Monitor in Panel

Panel mount monitors are designed to provide protection against

water and dust to NEMA Types 1, 12, 4X (indoor use only) or

IP65 equivalent standards.

Slides or shelves are not required because panel mount monitors are

designed to be supported by the panel in which they are installed.

Mounting Hardware

The 6186-M is shipped with the following mounting hardware for

panel mounting:

Tools Required

In addition to the tools required to make the cutout, you will need the

following tools:

• #2 Phillips torque screwdriver

Item Description Used For Quantity

Mounting Clips Panel Mounting 8 (VersaView 1200M)

10 (VersaView 1500M and 1700M)

14 (VersaView 2000M, non

rack-mount versions only)

Allen-Bradley Spares

Publication 6186M-UM001D-EN-P

2-8 Installation

Panel Mounting Guidelines

Observe the following precautions when installing the unit in a panel:

• Confirm that there is adequate space behind the panel.

– Allow at least 26 mm (1.0 in.) on the sides and bottom and

51 mm (2.0 in.) on the top for ventilation.

– A cabinet with a minimum depth of 74 mm (2.9 in.) is

sufficient.

• Take precautions so that metal cuttings do not enter any

components that are already installed in the panel.

• Supporting panels should be at least 14 gauge to ensure proper

sealing against water and dust, and to provide proper support.

The mounting hardware supplied accommodates panels up to

6.25 mm (0.25 in.) thick.

Installing Panel Mount Monitor

1. Prepare panel cutout for monitor. Refer to cutout drawings on

page 2-4.

2. If access to the rear of the monitor is not available following

installation, attach the cables to the monitor at this time. Refer

to Monitor Connections on page 2-15 for complete details.

3. Make sure the monitor’s sealing gasket is properly positioned on

the monitor. This gasket forms a compression type seal. Do not

use sealing compounds.

4. Place the monitor in the panel cutout.

IMPORTANT

Supporting panels must be cut to specifications

before installation.

ATTENTION

Failure to follow these warnings may result in

personal injury or damage to the panel components.

Publication 6186M-UM001D-EN-P

Installation 2-9

5. Install the mounting clips. The mounting clips slide into the slots

on the top, side and bottom of the monitor.

6. Gradually tighten the clips one at a time around the bezel using

the specified sequence. Note that the sequence begins with the

center clips and continues to the corner clips.

Repeat this process at least three times until the clips are

hand-tight and the gasket is compressed uniformly against the

panel.

7. Tighten mounting clips to a torque of 10 in-lbs (1.1 N•m) in the

sequence shown in step 6. Do not over-tighten.

Mounting Clips for VersaView 1500M /1700M

(The number of mounting clips varies by model)

Torque

Sequence

Torque

Sequence

8

157

26

43

715

628

93

410

VersaView 1500M and 1700MVersaView 1200M

Torque

Sequence

14 1 5

13

4

VersaView 2000M

6

11 10 2 9

12

7

3

8

ATTENTION

Tighten mounting clips to a torque of 10 in-lbs (1.1

N•m) to provide a proper seal and prevent damage

to the monitor. Rockwell Automation assumes no

responsibility for water or chemical damage to the

monitor or other equipment within the enclosure

because of improper installation.

Allen-Bradley Spares

Publication 6186M-UM001D-EN-P

2-10 Installation

Installing Monitor in a Rack

The rack-mount version of the 2000M monitor installs directly into a

rack. You can install other VersaView monitors into a rack using the

appropriate rack adapter:

Tools Needed for Rack Mount Installation

You will need the following tools:

• Rack adapter kit

• #2 Phillips screwdriver

Rack Mounting Guidelines

Observe the following precautions when installing this unit in a rack:

• The cabinet must be tall enough to accommodate the monitor’s

panel height.

• The cabinet must be deep enough to accommodate the

monitor’s depth while providing rear clearance for cabling and

airflow. The following cabinet depths are sufficient:

– 74 mm (2.9 in.)

• No slides or shelves are required because the rack mount

monitor is designed to be supported by the rack in which it is

installed.

Adapter Catalog Number Description

6189V-MRA12 Rack adapter for VersaView 1200M

6189V-MRA15 Rack adapter for VersaView 1500M

6189V-MRA17 Rack adapter for VersaView 1700M

Page is loading ...

Allen-Bradley VersaView 6186-M User manual

This manual is also suitable for

Allen-Bradley VersaView 6186-M User manual

Related papers

Other documents