The jbc P005 Pedal and Adapter Kit is a versatile tool that enhances the functionality of your JBC soldering station or compatible peripherals. It allows you to control various functions with the foot pedal, such as activating the soldering iron, dispensing solder paste, or extracting fumes. With its ergonomic design and customizable settings, the P005 streamlines your workflow and improves productivity.
The jbc P005 Pedal and Adapter Kit is a versatile tool that enhances the functionality of your JBC soldering station or compatible peripherals. It allows you to control various functions with the foot pedal, such as activating the soldering iron, dispensing solder paste, or extracting fumes. With its ergonomic design and customizable settings, the P005 streamlines your workflow and improves productivity.
INSTRUCTION MANUAL
Pedal + Adapter Kit
P005
2
Pedal .............................................................1 unit
Manual .................................................... 1 unit
Ref. 0028920
Packing List
The following items are included:
This manual corresponds to the following references:
P-005
Adapter .........................................................1 unit
3
Pedal
Ref. P-005
Connection to Control Units or Peripherals
Connect the pedal to JBC station or peripherals. The connector is identified by the designation
“ P E D A L”.
Connection to AL
Connect the pedal by means of the adpter cablet to the AL station. The connector at the rear of the
station is identified by the designation “PEDAL”.
Adapter Cable
40 mm
50 mm
60 mm
80 mm
100 mm
130 mm 130 mm
para manuales - color gris
200 mm
300 mm
4
Pedal Compatibility
Pedals
P405* P305* P005
Control
Unit
DIU
DDU
DMU
HDU
JNAU
JTU
WSU
ALU
NAU
Station AL
Module
MSE
MVE
MNE
Preheater
PHNK
PHSK
PHBK
PHXK
Fume
Extractor
FAE1
FAE2
* not included, sold separately
P005 is compatible with JBC devices as shown in the table in the highlighted column.
P305* and P405* is also shown in the table below.
Marked with means pedal P005 cannot be connected directly to JBCs control unit. A module
must be used (See next pages “Pedal Set Up”).
Peripherals Port 2-PA
17:14
Pedal PD_a
Function Extractor
Mode released
Minimum time 0 sec
Back
Peripherals Port 2-PA
17:14
Pedal PD_a
Module MSE
Pedal
PD_a
PD_b
None
Peripherals Port 2-PA
17:14
Pedal PD_a
Module MSE
5
Select how the pedal
acts: as Sleep,
Extractor (hibernation)
or as a module switch.
Select the activating
mode of the pedal
(pressed/released)
Pedal Set Up for:
- DDU, HDU, NAU, JNAU, JTU, ALU (Control Units)
- PHNK, PHSK, PHBK, PHXK (Preheaters)
Select port
Note that your first
connection is denoted
as “a”, the second
being “b”, etc. (e.g.
PD_ a, PD_ b,...)
Set the duration
of the activation
time when pressing
the pedal once*.
For continuous
functioning keep the
pedal pressed.
*NB: The same can be applied inversely by continually pressing the pedal and releasing to activate.
3. Set the pedal function according to your work needs:
2. Select the pedal from the list.
1. Enter the Peripherals Menu and select the port which you want to join to the pedal.
Note: Peripheral moduls - MSE, MVE or MNE - are needed to connect the pedal to DDU y HDU.
40 mm
50 mm
60 mm
80 mm
100 mm
130 mm 130 mm
para manuales - color gris
200 mm
300 mm
Peripherals
17:14
Port 1 2 3 4
MS a
?
PERIPHERAL
Peripheral 1 plugged:
Electric Suction Module
Setup Postpone
Peripherals
17:14
Port 1 2 3 4
MS a
PD a
?
6
Note: Peripheral moduls - MSE, MVE or MNE - are needed to connect the pedal to DMU.
After connecting one of the mentioned moduls to the station a popup window opens.
2. Select the module from the list of peripheral connections. Remember your first connection is
denoted as “a”, the second being “b”, etc. (e.g. MS_a, MS_b,...). Do the same with the pedal (e.g.
PD_a,...)
3. Select the port of the tool you want to link to the peripheral.
Pedal Set Up for DMU (Control Unit)
1. To configure the module MSE/MVE/MNE press Setup in the popup window.
4. Press Menu or Back to save changes.
Once set up, the module settings can be changed by entering the Peripherals Menu .
4 Filter set
5 Counters
6 Program version
Main menuMain menu
Exit
1 Reset
2
Unit
3
Port
PortPort
1 Program Ctm - 100%
2
Delay to stop
3
Pedal
BackBack
PedalPedal
1 Activation One-touch
2 Mode Pressed
BackBack
7
Pedal Set Up for FAE1, FAE2 (Fume Extractors)
Select Port
* One-touch activates the pedal funtion until pressed twice. Continous activates the pedal function
while pressing the pedal.
3. Set the pedal function according to your work needs:
2. At the Port Menu select Pedal.
1. Enter the Main Menu and select Port.
Select Pedal
Shows the activation mode.
Choose between One-
touch* and Continous*.
Select the activating mode of
the pedal. Choose between
Pressed and Released.
40 mm
50 mm
60 mm
80 mm
100 mm
130 mm 130 mm
para manuales - color gris
200 mm
300 mm
8
Pedal Set Up for AL (Auto Feed Soldering Station)
The choosed wire dispensing operation mode will be applied for the tool button as well as for the
pedal activation.
The working mode can be switched to:
- Continous: Solderwire is being fed constantly as long as the pedal or the tool button is activated.
- Discontinous: A predetermined solder wire amount is being fed every time the pedal or tool button
is being pressed.
Navigate throug the menu by pressing , use or to change the value. Confirm the
selection by pressing .
P005
P105
P305
P405
PORT 2
PERIPHERALS
FAE/
ROBOT
PORT 1
DDU
www.jbctools.com
1 2 3
SW1
P305
Conguration
Switch
SUPPORT
CONNECTION PEDAL
STATION TOOL
PORT 2
PERIPHERALS
FAE/
ROBOT
PORT 1
DDU
MSE
www.jbctools.com
STATION TOOL
9
Tool
Control Unit
1
Example:
Chip Compoments Rework Process using Tweezers and Pedal
Pedal
Connections
Connect the stand and the module to to the control unit. The Tool must be connected to the stand.
Then connect pedal P005 to the module.
In the peripherals menu for the “Pedal Activation Mode” choose between “pressed” and “released” for
the pedalactivation mode (see page 5).
The Pedal is frequently used to rework components with tweezers.
The adjustable micro tweezers of the AM120 JBC not only provide a perfect solution for SMD chip
components and small/medium SOP of PCB assemblies, but also facilitate their quick placement and
soldering using the P005 pedal.
Module
Stand
40 mm
50 mm
60 mm
80 mm
100 mm
130 mm 130 mm
para manuales - color gris
200 mm
300 mm
10
3
4
Pad Cleaning
Clean the pads with JBC´s desoldering tool
DS360.
For this operation JBC´s desoldering station
DSS is needed.
Solder Paste Dispensing
Apply the solder paste amount needed to
solder the new chip component.
The use of JBC´s DPM solder paste dispenser
is recommended.
DPM
Manual
Solder Paste Dispenser
DS360
Micro
Desoldering Iron
Desoldering*
Lift the tool from the holder, press and hold
the pedal to activate the tool and desolder the
component.
Once the pedal is released the tool enters in
hibernation mode and cools down.
2
* “Press Mode” previously selected
11
5
6
Placing
Do not press the pedal.
Use the tool to position the component on the
previously tinned pad.
Note:
The inactive tool prevents the component from
heating up prematurely.
Soldering
Once in position press and hold the pedal to
activate the tool and perform the soldering.
40 mm
50 mm
60 mm
80 mm
100 mm
130 mm 130 mm
para manuales - color gris
200 mm
300 mm
This product should not be thrown in the garbage.
In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must
be collected and returned to an authorized recycling facility.
Warranty
JBC’s 2 year warranty covers this equipment against
all manufacturing defects, including the replacement
of defective parts and labour.
Warranty does not cover product wear or misuse.
In order for the warranty to be valid, equipment must
be returned, postage paid, to the dealer where it was
purchased.
40 mm
50 mm
60 mm
80 mm
100 mm
130 mm 130 mm
para manuales - color gris
200 mm
300 mm
P005
Pedal + Adapter Kit
Ref. P-005
- Cable length: 1.9 m / 74.80 in
- Total Net weight: 414 g / 0.91 lb
- Total Package Dimension / Weigt: 300 x 125 x 65 mm / 560 g
(L x W x H) 11.81 x 4.92 x 2.56 in / 1.23 lb
Complies with CE standards
ESD safe
Specifications
0028920-170522
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
The jbc P005 Pedal and Adapter Kit is a versatile tool that enhances the functionality of your JBC soldering station or compatible peripherals. It allows you to control various functions with the foot pedal, such as activating the soldering iron, dispensing solder paste, or extracting fumes. With its ergonomic design and customizable settings, the P005 streamlines your workflow and improves productivity.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
JBC Tools H0511 User manual
-
Mindray Resona 7 User manual
-
Pace MBT 360 Multi-Channel Soldering and Rework Station User manual
-
Weller WXD 2 Operating Instructions Manual
-
Winmate FA30-200 User manual
-
-
Winmate FA30-210 User manual
-
blucoil GE200 User manual
-
Winmate FA33 User manual
-
SsangYong 1999 Musso User manual
