jbc P405 User manual

Brand: jbc

Model: P405

Type: User manual

The jbc P405 pedal is a versatile tool designed to enhance your soldering experience and streamline your workflow. With its durable construction and ergonomic design, it provides precise control and activation of various functions, allowing you to focus on your soldering tasks. The pedal can be easily connected to JBC stations or peripherals via the designated "PEDAL" connector. It offers a range of customizable settings, enabling you to tailor its behavior to your specific needs. Whether you're a hobbyist or a professional, the jbc P405 pedal is a valuable addition to your soldering arsenal.

INSTRUCTION MANUAL

Pedal

P405

Pedal

Ref. P-405

Pedal ..............................................................1 unit Manual .................................................... 1 unit

Ref. 0028917

Connections

Packing List

The following items are included:

This manual corresponds to the following references:

P-405

Connect the pedal to JBC station or peripherals. The connector is identified by the designation

“ P E D A L”.

Pedal Compatibility

Pedals

P405 P305* P005*

Control

Unit

DDE

DME

HDE

JNASE

JTSE

ALE

NAE

Station ALE

Module

MS/MSE

MV/MVE

MN/MNE

Preheater

PHNE

PHSE

PHBE

PHXLE

Fume

Extractor

FAE1

FAE2

* not included, sold separately

P405 is compatible with JBC devices as shown in the table in the highlighted column.

P305* and P005* is also shown in the table below.

Marked with means pedal P405 cannot be connected directly to JBCs control unit. A module

must be used (See next pages “Pedal Set Up”).

40 mm

50 mm

60 mm

80 mm

100 mm

130 mm 130 mm

para manuales - color gris

200 mm

300 mm

Peripherals Port 2-PA

17:14

Pedal PD_a

Function Extractor

Mode released

Minimum time 0 sec

Back

Peripherals Port 2-PA

17:14

Pedal PD_a

Module MSE

Pedal

PD_a

PD_b

None

Peripherals Port 2-PA

17:14

Pedal PD_a

Module MSE

Select how the pedal

acts: as Sleep,

Extractor (hibernation)

or as a module switch.

Select the activating

mode of the pedal

(pressed/released)

Pedal Set Up for:

- DDU, HDU, NAU, JNAU, JTU, ALU (Control Units)

- PHNK, PHSK, PHBK, PHXK (Preheaters)

Select port

Note that your first

connection is denoted

as “a”, the second

being “b”, etc. (e.g.

PD_ a, PD_ b,...)

Set the duration

of the activation

time when pressing

the pedal once*.

For continuous

functioning keep the

pedal pressed.

*NB: The same can be applied inversely by continually pressing the pedal and releasing to activate.

3. Set the pedal function according to your work needs:

2. Select the pedal from the list.

1. Enter the Peripherals Menu and select the port which you want to join to the pedal.

Note: Peripheral moduls - MSE, MVE or MNE - are needed to connect the pedal to DDU y HDU.

Peripherals

17:14

Port 1 2 3 4

MS a

PERIPHERAL

Peripheral 1 plugged:

Electric Suction Module

Setup Postpone

Note: Peripheral moduls - MSE, MVE or MNE - are needed to connect the pedal to DMU.

After connecting one of the mentioned moduls to the station a popup window opens.

2. Select the module from the list of peripheral connections. Remember your first connection is

denoted as “a”, the second being “b”, etc. (e.g. MS_a, MS_b,...). Do the same with the pedal (e.g.

PD_a,...)

3. Select the port of the tool you want to link to the peripheral.

Pedal Set Up for DMU (Control Unit)

1. To configure the module MSE/MVE/MNE press Setup in the popup window.

4. Press Menu or Back to save changes.

Once set up, the module settings can be changed by entering the Peripherals Menu .

Peripherals

17:14

Port 1 2 3 4

MS a

PD a

40 mm

50 mm

60 mm

80 mm

100 mm

130 mm 130 mm

para manuales - color gris

200 mm

300 mm

Pedal Set Up for FAE1, FAE2 (Fume Extractors)

Select Port

* One-touch activates the pedal funtion until pressed twice. Continous activates the pedal function

while pressing the pedal.

3. Set the pedal function according to your work needs:

2. At the Port Menu select Pedal.

1. Enter the Main Menu and select Port.

4 Filter set

5 Counters

6 Program version

Main menuMain menu

Exit

1 Reset

Unit

Port

PortPort

1 Program Ctm - 100%

Delay to stop

Pedal

BackBack

PedalPedal

1 Activation One-touch

2 Mode Pressed

BackBack

Select Pedal

Shows the activation mode.

Choose between One-

touch* and Continous*.

Select the activating mode of

the pedal. Choose between

Pressed and Released.

ROBOT

Tweezers

Nano Control Unit

Example:

Chip Compoments Rework Process using Tweezers and Pedal

P405

Pedal

Connections

Connect pedal P405 to the same port where

AN115 nano tweezers are connected.

In the peripherals menu for the “Pedal

Activation Mode” choose between “pressed”

and “released”.

The Pedal is frequently used to rework components with tweezers.

AN115, JBCs Adjustable Nano Tweezers, is the most effective tool for desoldering chip components

but also it facilitates its rapid placement and soldering by using P405 pedal connected to JBC´s NAS

station.

connect to

the same port

40 mm

50 mm

60 mm

80 mm

100 mm

130 mm 130 mm

para manuales - color gris

200 mm

300 mm

NAE

Control Unit

PORT

ROBOT

PEDAL

NAE

Control Unit

PORT

ROBOT

PEDAL

ROBOT

C115

C11

C105 /

C105 / C115

19:29

Port

Actual Temp. 25ºC

NT105

ºC

Power

45%

Selected 350ºC

350

Port

NT105

Hibernation

19:29

Port

Actual Temp. 25ºC

AN115

Hibernation

19:29

ºC

Power

45%

Selected 350ºC

350

Port

AN115

No Yes

Pad Cleaning

Clean the pads with JBC´s desoldering tool

DS360.

For this operation JBC´s desoldering station

DSS is needed.

Solder Paste Dispensing

Apply the solder paste amount needed to

solder the new chip component.

The use of JBC´s DPM solder paste dispenser

is recommended.

DPM

Manual

Solder Paste

Dispenser

DS360

Micro

Desoldering Iron

Desoldering*

Lift the tweezers from the holder, press and

hold the pedal to activate the tweezers and

desolder the component.

Once the pedal is released the tweezers enters

in hibernation mode and cools down.

* “Press Mode” previously selected

Soldering

Once in position press and hold the pedal

to activate the tweezers and perform the

soldering.

Placing

Do not press the pedal.

Use the tweezers to position the component

on the previously tinned pad.

Note:

The inactive tweezers prevents the component

from heating up prematurely.

40 mm

50 mm

60 mm

80 mm

100 mm

130 mm 130 mm

para manuales - color gris

200 mm

300 mm

Notes

40 mm

50 mm

60 mm

80 mm

100 mm

130 mm 130 mm

para manuales - color gris

200 mm

300 mm

This product should not be thrown in the garbage.

In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must

be collected and returned to an authorized recycling facility.

Warranty

JBC’s 2 year warranty covers this equipment against

all manufacturing defects, including the replacement

of defective parts and labour.

Warranty does not cover product wear or misuse.

In order for the warranty to be valid, equipment must

be returned, postage paid, to the dealer where it was

purchased.

40 mm

50 mm

60 mm

80 mm

100 mm

130 mm 130 mm

para manuales - color gris

200 mm

300 mm

P405

Pedal

Ref. P-405

- Cable length: 1.9 m / 74.80 in

- Total Net weight: 232 g / 0.51 lb

- Total Package Dimension / Weigt: 155 x 85 x 55 mm / 255 g

(L x W x H) 6.10 x 3.35 x 2.17 in / 0.56 lb

Complies with CE standards

ESD safe

Specifications

0028917-291122

jbc P405 User manual

jbc P405 User manual

Related papers

Other documents