Altronix eBridge4SK Series Installation guide

Brand: Altronix

Model: eBridge4SK Series

Category: Security cameras

Type: Installation guide

Altronix eBridge4SK Series is a kit consisting of eBridge100SPR and eBridge4SPT which are Coax to CAT5 Ethernet adapters/media converters that deliver data and power over coax cable. eBridge4SK enables fast 10/100 Base-T Ethernet digital communication. eBridge4SPT allows you to upgrade your existing infrastructure by replacing a single analog device with up to four (4) PoE/PoE+ devices. With a maximum range of 300m from head end to the PoE camera/device, eBridge4SK enables cost-effective system upgrades and eliminates the costs and labor associated with installing new network cabling.

More than just power.

Rev. 072313

I.T.E. 43KC

Z1409

PLUS

eBridge4SK

Ethernet over Coax 4-Port Adapter Kit

eBridge100SPR - EoC Receiver

eBridge4SPT - 4-Port PoE/PoE+ EoC Transceiver Switch

Installation Guide

- 2 - eBridge4SK

Table of Contents:

Overview .................................................................................................pg. 3

Features .......................................................................pg. 3

Installation Instructions ..........................................................pg. 4

Technical Specifications ..........................................................pg. 4

Typical Application .............................................................pg. 5

Maximum Length of Coax Type vs. Camera Power/PoE Class .........................pg. 5

Chassis Mechanical Drawing & Dimensions .........................................pg. 8

Shelf Installation ................................................................pg. 8

eBridge4SK - 3 -

Overview:

Altronix eBridge4SK kit consists of eBridge100SPR and eBridge4SPT which are Coax to CAT5 Ethernet

adapters/media converters that deliver data and power over coax cable. eBridge4SK enables fast 10/100 Base-T

Ethernet digital communication. eBridge4SPT allows you to upgrade your existing infrastructure by replacing a

single analog device with up to four (4) PoE/PoE+ devices. eBridge100SPR passes data and sends power over

the coax to the eBridge4SPT. Data transmission and power over the Coax are possible up to 300m. Maximum

range from head end to the PoE camera/device is 500m, taking into consideration that up to 100m of structured

cable may be deployed at each end. eBridge4SK enables cost-effective system upgrades and eliminates the costs

and labor associated with installing new network cabling.

Note: for Ethernet maximum distance see Maximum Length of Coax Type vs. Camera Power/PoE Class, pg. 5.

Features:

Agency Listings:

• UL 60950-1 Information Technology Equipment.

• CE European Conformity.

• C-Tick C-Tick compliant.

Input:

• eBridge100SPR - 51-56VDC/60W max. power.*

eBridge4SPT - powered by eBridge100SPR.

Power Output:

• eBridge4SPT: 4 ports PoE+ (30W) per port.

• Total output power: 60W.

Ethernet:

• Connectivity: RJ45, auto-crossover.

• Wire type: 4-pair CAT5e or better structured cable.

• Distance: up to 100m.

• Speed: 10/100BaseT, half/full duplex,

auto negotiation.

Coax:

• Throughput is rated to pass 100Mbps of data at

distances up to 300m.

• Connectivity: BNC, RG-59/U or similar.

• Throughput is rated to pass 100Mbps from camera

to receiver. With the proper headend equipment

multiple Megapixel cameras can be used.

LED Indicators:

• Blue LED - Coax link connection.

• Green LED - Power (eBridge100SPR only).

• Yellow and Green LED (RJ45) IP Link status,

10/100Base-T/active.

Environmental:

• Operating Ambient Temperature :

eBridge100SPR: – 40ºC to 60ºC

(– 40ºF to 140ºF).

eBridge4SPT (60W): – 40ºC to 75ºC

(– 40ºF to 167ºF).

• Storage Temperature: – 40ºC to 75ºC

(– 40ºF to 167ºF).

• Humidity: 20 to 85%, non-condensing.

Applications:

• Retrofit digital IP cameras in an analog CCTV

installation (up to four (4) IP cameras expansion per

analog camera).

• Works with Megapixel, HD720, HD1080 and VGA

(SD) cameras (see note, pg. 4).

• Extend Network link distance in an

industrial environment.

• Upgrade deployed CCTV Coax to a digital network

in Retail, Hospitality, Arenas, Casinos, Airports,

Schools, Hospitals, Transportation, etc.

Mechanical:

• Dimensions (H x W x D approx.):

eBridge100SPR:

4.375” x 3.5” x 1” (111.1mm x 88.9mm x 25.4mm)

eBridge4SPT:

1.75” x 5.25” x 9.25” (44.5mm x 133.4mm x 235mm)

*UL Listed Class 2 or limited power source (NetWay1D).

- 4 - eBridge4SK

Installation Instructions:

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local

codes and authorities having jurisdiction.

Wiring should be UL Listed and/or Recognized wire suitable for the application.

eBridge100SPR and eBridge4SPT is not intended to be connected to outside plant leads and should be installed

indoors within the protected premises. eBridge100SPR and eBridge4SPT are intended for indoor use only.

1. eBridge100SPR installation:

a. Secure unit to desired mounting surface with a proper fastening device utilizing the unit’s mounting hole.

Unit should be mounted in proximity to Ethernet switch/network, NVR or video server.

b. Connect 56VDC UL Listed Class 2 or limited power source to terminals marked [Power – Input +]

(observe proper polarity) (Fig. 1, pg. 5). Use 22AWG-16AWG wire for this connection.

Caution: 56VDC will be present on coax. The other end of the coax should only be connected to the

eBridge4SPT.

c. Connect structured cable from Ethernet switch/NVR (network video server) to RJ45 jack marked

[10/100 BaseT] (Fig. 1, pg. 5).

d. Connect Coax cable to BNC connector marked [Coax] (Fig. 1, pg. 5).

2. eBridge4SPT installation:

a. Affix rubber pads to eBridge4SPT for shelf installation (Fig. 3, pg. 8).

b. Connect Coax cable from eBridge100SPR to BNC connector marked [Coax] located on the back of the

unit (Fig. 1, pg. 5).

c. Connect structured cable from PoE/PoE+ cameras/devices to RJ45 jacks marked [1-4] (Fig. 1, pg. 5).

Note: The eBridge is designed to accommodate Megapixel, HD720, HD1080 and VGA (SD) cameras. It is

important to note that some high resolution and high frame rate cameras may demand faster headend processing

ability, such as a PC graphics card to present a quality image. If the headend processing equipment is insufficient

in speed, the image may show pixelation and latency. It is advisable to pre-test system if unsure. Alternatively,

frame rate and resolution may be reduced to accommodate system equipment.

Technical Specifications:

Parameter Description

Connections

BNC for Coax link. RJ45 for Ethernet link.

Input Power

Requirements

eBridge100SPR - 51-56VDC/60W @ max. power.

eBridge4SPT - powered by eBridge100SPR.

Indicators

Blue: Coax Link.

Yellow (RJ45 connector): On - Link, Off - No Link, Blinking - Activity.

Green (RJ45 connector): On - 100Base-TX, Off - 10Base-T.

Environmental

Conditions

Operating Ambient Temperature (UL60950-1):

eBridge100SPR: – 40ºC to 60ºC (– 40ºF to 140ºF).

eBridge4SPT (60W): – 40ºC to 75ºC (– 40ºF to 167ºF).

Relative humidity: 85%, +/ – 5%

Storage Temperature: – 40ºC to 75ºC (– 40ºF to 167ºF).

Operating Altitude: – 304.8 to 2,000m.

Regulatory

Compliance

UL/cUL Listed for Information Technology Equipment (UL 60950-1). CE approved.

Weights (approx.)

eBridge100SPR: Product: 5.1 oz. (0.144 kg) | Shipping: 7.76 oz. (0.22 kg).

eBridge4SPT: Product: 2.9 lbs. (1.32 kg) | Shipping: 3.9 lbs. (1.77 kg).

eBridge4SK - 5 -

Coax up to 300m

Ethernet Switch

NVR Network

Video Server

(Head End

Equipment)

eBridge4SPT (Front View)

eBridge100SPR

CAT-5e

up to 100m

CAT-5e

up to

100m

CAT-5e

up to

100m

PoE

Output

10/100

Base-T

PoE/PoE+

Cameras

PoE/PoE+

Cameras

56VDC

Input

Typical Application:

Fig. 1

Maximum Length of Coax Type vs. Camera Power/PoE Class:

Camera Power/

PoE Class

RG59/U

(23AWG)

RG59/U

(22AWG)

RG59/U

(20AWG)

RG59/U

(18AWG)

RG6/U

(18AWG)

Max. Length (meters)

13W/0 or 13W/3 261m 335m 500m 500m 500m

25W 119m 151m 240m 366m 366m

60W 51m 64m 101m 160m 160m

- 6 - eBridge4SK

Notes:

eBridge4SK - 7 -

Notes:

- 8 - eBridge4SK

Altronix is not responsible for any typographical errors.

140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056

website: www.altronix.com | e-mail: [email protected] | Lifetime Warranty | Made in U.S.A.

IIeBridge4SK H20R

MEMBER

Mounting Hardware (Included):

Four (4) rubber pads

Rubber Feet

Left side

Fig. 3

Shelf Installation

1- Position and affix rubber pads (C) (included) at each corner on the bottom of the unit (Fig. 3).

2- Place unit in desired location.

eBridge4SPT Chassis Mechanical Drawing & Dimensions

(H x W x D approx.):

1.75” x 5.25” x 9.25” (44.5mm x 133.4mm x 235mm)

Fig. 2

8.42”

(213.9mm)

5.25” (133.4mm)

1.75”

(44.5mm)

9.25”

(235mm)

Coax SLOC

link LED

PoE

Output

10/100

Base-T

Altronix eBridge4SK Series Installation guide

Brand: Altronix

Model: eBridge4SK Series

Category: Security cameras

Type: Installation guide

Download PDF

report

Altronix eBridge4SK Series Installation guide

Altronix eBridge4SK Series Installation guide

Related papers

Other documents