Altronix eBridge100SPR Installation guide

Type
Installation guide

Altronix eBridge100SPR is an EoC (Ethernet over Coax) receiver that enables the transmission of data and power over a single coaxial cable. It allows for the extension of network connectivity and power to PoE (Power over Ethernet) devices such as IP cameras, access points, and VoIP phones over long distances, specifically up to 300 meters over coax and an additional 100 meters over Ethernet cable. It supports high-speed data transmission of up to 100Mbps and PoE power output of up to 60W, making it suitable for Megapixel, HD720, HD1080, and VGA (SD) cameras.

Altronix eBridge100SPR is an EoC (Ethernet over Coax) receiver that enables the transmission of data and power over a single coaxial cable. It allows for the extension of network connectivity and power to PoE (Power over Ethernet) devices such as IP cameras, access points, and VoIP phones over long distances, specifically up to 300 meters over coax and an additional 100 meters over Ethernet cable. It supports high-speed data transmission of up to 100Mbps and PoE power output of up to 60W, making it suitable for Megapixel, HD720, HD1080, and VGA (SD) cameras.

PLUS
Overview:
Altronix eBridge100SPR passes data and sends power over the coax to eBridge200WPMT. Data transmission and
power over the Coax is possible up to 300m. Maximum range from headend to the PoE camera/device is 500m,
taking into consideration that up to 100m of structured cable may be deployed at each end. Built in IP management
allows for remote camera reset, monitoring, and reporting via various IP protocols.
Note: Ethernet maximum distance (see Maximum Length of Coax Type vs. Camera Power/PoE Class, pg. 3).
Features:
*UL Listed Class 2 or limited power source.
eBridge100SPR
EoC Receiver
Installation Guide
I.T.E. 43KC
Agency Listings:
UL/cUL Listed for Information
Technology Equipment (UL 60950-1).
CE European Conformity.
Input:
51-56VDC/60W max. power.*
Power Output:
Total output power: 60W.
Ethernet:
Connectivity: RJ45, auto-crossover.
Wire type: 4-pair Cat-5 or better structured cable.
Distance: up to 100m.
Speed: 100BaseT, half/full duplex, auto negotiation.
Coax:
Distance: up to 300m.
Connectivity: BNC, RG-59/U or similar.
Throughput is rated to pass 100Mbps from camera
to receiver. Data distances of up to 300m can be
achieved. With the proper headend equipment
multiple Megapixel cameras can be used.
LED Indicators:
Blue LED - Coax link connection.
Green LED - Power.
Yellow and Green LED (RJ45) IP Link status,
100Base-T/active.
Environmental:
Operating temperature:
20ºC to 50ºC (4ºF to 122ºF).
Storage temperature:
30ºC to 70ºC (22º to 158ºF).
Humidity: 20 to 85%, non-condensing.
Applications:
Works with Megapixel, HD720, HD1080 and
VGA (SD) cameras (see note, pg. 2).
Extend Network link distance in an industrial
environment.
Upgrade deployed CCTV Coax to a digital network
in Retail, Hospitality, Arenas, Casinos, Airports,
Schools, Hospitals, Transportation, etc.
Mechanical:
Dimensions (W x L x H approx.):
3.5” x 4.375” x 1” (88.9mm x 111.1mm x 25.4mm).
- 2 - eBridge100SPR Installation Guide
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes
and authorities having jurisdiction. Wiring should be UL Listed and/or Recognized wire suitable for the application.
eBridge100SPR is not intended to be connected to outside plant leads and should be installed indoors within
the protected premises. The eBridge100SPR is intended for indoor use only.
1. Secure unit to desired mounting surface with a proper fastening device utilizing the unit’s mounting hole.
Unit should be mounted in proximity to ethernet switch/network, NVR or video server.
2. Connect 56VDC UL Listed Class 2 or limited power source to terminals marked [Power – Input +]
(polarity observed) (Fig. 1, pg. 2). Use 22AWG-16AWG wire for this connection.
Caution: 56VDC will be present on coax. The other end of the coax should only be connected to the
eBridge200WPM.
3. Connect structured cable from ethernet switch/NVR (network video server) to RJ45 jack marked [10/100 BaseT]
(Fig. 1, pg. 2).
4. Connect Coax cable to BNC connector marked [Coax].
5. Refer to eBridge200WPM for proper connection and setup information.
Note: The eBridge is designed to accommodate Megapixel, HD720, HD1080 and VGA (SD) cameras. It is impor-
tant to note that some high resolution and high frame rate cameras may demand faster headend processing abil-
ity, such as a PC graphics card to present a quality image. If the headend processing equipment is insufficient in
speed, the image may show pixelation and latency. It is advisable to pretest system if unsure. Alternatively, frame
rate and resolution may be reduced to accommodate system equipment.
Technical Specifications:
Parameter Description
Connections BNC for Coax link. RJ45 for ethernet link.
Input Power Requirements 51-56VDC/60W @ max. power.
Indicators
Blue: Coax Link.
Yellow (RJ45 connector): On - Link, Off - No Link, Blinking - Activity.
Green (RJ45 connector): On - 100Base-TX, Off - 10Base-T.
Environmental Conditions
Operating ambient temperature (UL60950-1): 20ºC to 50ºC (4ºF to 122ºF).
Storage temperature: 30ºC to 70ºC (22º to 158ºF).
Relative humidity: 85%, +/– 5%.
Operating Altitude: 304.8 to 2,000m.
Regulatory Compliance UL/cUL Listed for Information Technology Equipment (UL 60950-1).
CE European Conformity.
Weights (approx.) Product: 5.1 oz. (0.144 kg) | Shipping: 7.76 oz. (0.22 kg)
Cable Type, Total Device Power, Data, and Power Distance:
Cable Type
Total
Power
Consumption
Max.
Data
Distance
Max.
Power
Distance
Cable Type
Total
Power
Consumption
Max.
Data
Distance
Max.
Power
Distance
RG59u/23awg 15W 300m 264m RG59u/20awg 15W 300m 532m
RG59u/23awg 30W 300m 132m RG59u/20awg 30W 300m 266m
RG59u/23awg 60W 300m 66m RG59u/20awg 60W 300m 133m
RG59u/22awg 15W 300m 334m RG59u/18awg 15W 300m 846m
RG59u/22awg 30W 300m 167m RG59u/18awg 30W 300m 423m
RG59u/22awg 60W 300m 83m RG59u/18awg 60W 300m 211m
eBridge100SPR Installation Guide - 3 -
60W Coax Application:
Fig. 1
1
PORT 1 PORT 2
CAT INPUT
COAX INPUT
USB
SPEED ACTIVITY
SW3
SPEED
ACTIVITY
SPEED
ACTIVITY
SPR
PoE
DATA
PoE
SPR
PoE
DATA
PoE
60W CAT
30W CAT
or
60W COAX
SW3
60W CAT
30W CAT
or
60W COAX
CAT-5e - 100m
CAT-5e - 100mCAT-5e - 100m
Coax - 300m
Option 1 Option 2
30W Camera/Device
30W Camera/Device
60W Camera/Device
eBridge100SPR NetWay1D
I.T.E. 43KC www.altronix.com
Input: 51-56VDC Class 2 or LPS power supply
Blue LED Coax link status (SLOC)
RJ45 LEDs Yellow - Speed, Green - Activity
Green LED Power and PoE
Provides 56VDC
Coax
10/100
Base-T
Power LED
DC Power
Input
--- +
Z1409
eBridge100SPR - Receiver
Aux.
+ ---
INOUT
PoE
ON
LED
Link/Speed
Activity
- 4 - eBridge100SPR Installation Guide
Notes:
Altronix is not responsible for any typographical errors.
–––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
140 58th Street, Brooklyn, New York 11220 USA | 718-567-8181 | fax: 718-567-9056
website: www.altronix.com | e-mail: [email protected] | Lifetime Warranty
IIeBridge100SPR Rev. 102814 G19U MEMBER
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Altronix eBridge100SPR Installation guide

Type
Installation guide

Altronix eBridge100SPR is an EoC (Ethernet over Coax) receiver that enables the transmission of data and power over a single coaxial cable. It allows for the extension of network connectivity and power to PoE (Power over Ethernet) devices such as IP cameras, access points, and VoIP phones over long distances, specifically up to 300 meters over coax and an additional 100 meters over Ethernet cable. It supports high-speed data transmission of up to 100Mbps and PoE power output of up to 60W, making it suitable for Megapixel, HD720, HD1080, and VGA (SD) cameras.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI