Altronix eBridge100SPR Installation guide

eBridge100SPR
Altronix
Brand
Altronix
Model
eBridge100SPR
Type
Installation guide

Altronix eBridge100SPR is a high-performance EoC receiver designed for transmitting data and power over coax cables, enabling you to extend your network connectivity and power devices in remote locations. With its ability to deliver up to 60W of power and support data transmission speeds of up to 25mbps, it's ideal for powering and connecting IP cameras, PoE devices, and other network equipment.

Altronix eBridge100SPR is a high-performance EoC receiver designed for transmitting data and power over coax cables, enabling you to extend your network connectivity and power devices in remote locations. With its ability to deliver up to 60W of power and support data transmission speeds of up to 25mbps, it's ideal for powering and connecting IP cameras, PoE devices, and other network equipment.

PLUS
Rev. 102814
Installation Guide
eBridge100SPR - EoC Receiver
I.T.E. 43KC
Overview:
The eBridge100SPR passes data and sends power over the coax to the eBridge200WPMT. Data transmission and power
over the Coax is possible up to 300m. Maximum range from head end to the PoE camera/device is 500m taking into con-
sideration that up to 100m of structured cable may be deployed at each end. Built in IP management allows for remote
camera reset, monitoring and reporting via various IP protocols.
Note: Ethernet maximum distance (see Maximum Length of Coax Type vs. Camera Power/PoE Class, pg. 3).
Features:
Agency Listings:
• UL/CUL Listed for Information
Technology Equipment (UL 60950-1).
• CE approved.
Input:
• 51-56VDC/60W max. power.*
Power Output:
• Total output power: 60W.
Ethernet:
• Connectivity: RJ45, auto-crossover.
• Wire type: 4-pair Cat-5 or better structured cable.
• Distance: up to 100m.
• Speed: 100BaseT, half/full duplex, auto negotiation.
Coax:
• Distance: up to 300m.
• Connectivity: BNC, RG-59/U or similar.
• Throughput is rated to pass 25mbps from camera to
receiver. Data distances of up to 300m can be
achieved. With the proper headend equipment
multiple Megapixel cameras can be used.
*UL Listed Class 2 or limited power source.
LED Indicators:
• Blue LED - Coax link connection.
• Green LED - Power.
• Yellow and Green LED (RJ45) IP Link status,
100Base-T/active.
Environmental:
• Operating temperature: --- 20ºC to 50ºC (-- 4ºF to 122ºF).
• Storage temperature: ---- 30º to 70ºC (-- 22º to 158ºF).
• Humidity: 20 to 85%, non-condensing.
Applications:
• Works with Megapixel, HD720, HD1080 and VGA
(SD) cameras (see note, pg. 2).
• Extend Network link distance in an industrial
environment.
• Upgrade deployed CCTV Coax to a digital network
in Retail, Hospitality, Arenas, Casinos, Airports,
Schools, Hospitals, Transportation, etc.
Mechanical:
• Dimensions (H x W x D approx.):
4.375” x 3.5” x 1” (111.125mm x 88.89mm x 25.4mm)
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and
authorities having jurisdiction. Wiring should be UL Listed and/or Recognized wire suitable for the application.
eBridge100SPR is not intended to be connected to outside plant leads and should be installed indoors within the
protected premises. The eBridge100SPR is intended for indoor use only.
1. Secure unit to desired mounting surface with a proper fastening device utilizing the unit’s mounting hole.
Unit should be mounted in proximity to ethernet switch/network, NVR or video server.
2. Connect 56VDC UL Listed Class 2 or limited power source to terminals marked [Power --- Input +] (polarity
observed) (Fig. 1, pg. 2). Use 22AWG-16AWG wire for this connection.
Caution: 56VDC will be present on coax. The other end of the coax should only be connected to the
eBridge200WPM.
3. Connect structured cable from ethernet switch/NVR (network video server) to RJ45 jack marked [10/100 BaseT]
(Fig. 1, pg. 2).
4. Connect Coax cable to BNC connector marked [Coax].
5. Refer to eBridge200WPM for proper connection and setup information.
Note: The eBridge is designed to accommodate Megapixel, HD720, HD1080 and VGA (SD) cameras. It is important
to note that some high resolution and high frame rate cameras may demand faster headend processing ability, such as a
PC graphics card to present a quality image. If the headend processing equipment is insufficient in speed, the image may
show pixelation and latency. It is advisable to pretest system if unsure. Alternatively, frame rate and resolution may be
reduced to accommodate system equipment.
eBridge100SPR - 1 -
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]
I.T.E. 43KC
www. m
: y
Y y
D
r
t
---
Z1409
D
Technical Specifications:
Parameter Description
Connections BNC for Coax link. RJ45 for ethernet link.
Input power requirements 51-56VDC/60W @ max. power.
Indicators
Blue: Coax Link.
Yellow (RJ45 connector): On - Link, Off - No Link, Blinking - Activity.
Green (RJ45 connector): On - 100Base-TX, Off - 10Base-T.
Environmental Conditions
Operating ambient temperature: UL60950-1: --- 20ºC to 50ºC (-- 4ºF to 122ºF).
Relative humidity: 85%, +/ --- 5%.
Storage temperature: ---- 30º to 70ºC (-- 22º to 158ºF).
Operating Altitude: --- 1000 to 6,561.679 ft. (--- 304.8 to 2000m).
Regulatory Compliance UL/CUL Listed for Information Technology Equipment (UL 60950-1). CE approved.
Weights (approx.) Product: 5.1 oz. (0.144 kg.), Shipping: 7.76 oz. (0.22 kg.)
Cable Type, Total Device Power, Data and Power Distance:
Cable Type
Total
Power
Consumption
Max.
Data
Distance
Max.
Power
Distance
RG59u/23awg 15W 300m 264m
RG59u/23awg 30W 300m 132m
RG59u/23awg 60W 300m 66m
RG59u/22awg 15W 300m 334m
RG59u/22awg 30W 300m 167m
RG59u/22awg 60W 300m 83m
Cable Type
Total
Power
Consumption
Max.
Data
Distance
Max.
Power
Distance
RG59u/20awg 15W 300m 532m
RG59u/20awg 30W 300m 266m
RG59u/20awg 60W 300m 133m
RG59u/18awg 15W 300m 846m
RG59u/18awg 30W 300m 423m
RG59u/18awg 60W 300m 211m
60W Coax Application:
Fig. 1
Option 1 Option 2
1
PORT 1 PORT 2
CAT INPUT
COAX INPUT
USB
SPEED
ACTIVITY
SW3
SPEED
ACTIVITY
SPEED
ACTIVITY
SPR
PoE
DATA
PoE
SPR
PoE
DATA
PoE
60W CAT
30W CAT
or
60W COAX
SW3
60W CAT
30W CAT
or
60W COAX
CAT-5e - 100m
CAT-5e - 100m CAT-5e - 100m
Coax - 300m
30W Camera/Device
30W Camera/Device
60W Camera/Device
eBridge100SPR
NetWay1D
altronix.co
Input 51-56VDC Class 2 or LPS power suppl
Blue LED Coax link status (SLOC)
RJ45 LEDs ellow - Speed, Green - Activit
Green LED Power and PoE
Provides 56VDC
Coax
10/100
Base-T
Power LE
DC Powe
Inpu
+
eBridge100SPR - Receiver
Aux.
+ ---
INOUT
PoE
ON
LE
Link/Speed
Activity
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: 718-567-9056
website: www.altronix.com, e-mail: [email protected]. Lifetime Warranty, Made in U.S.A.
IIeBridge100SPR J28N
MEMBER
- 2 - eBridge100SPR
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]
  • Page 1 1
  • Page 2 2

Altronix eBridge100SPR Installation guide

eBridge100SPR
Altronix
Brand
Altronix
Model
eBridge100SPR
Type
Installation guide

Altronix eBridge100SPR is a high-performance EoC receiver designed for transmitting data and power over coax cables, enabling you to extend your network connectivity and power devices in remote locations. With its ability to deliver up to 60W of power and support data transmission speeds of up to 25mbps, it's ideal for powering and connecting IP cameras, PoE devices, and other network equipment.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents