Aventura CAM-AHY-5D-212V-IRVP Quick start guide

Aventura
Brand
Aventura
Model
CAM-AHY-5D-212V-IRVP
Type
Quick start guide

This manual is also suitable for

WWW.AVENTURACCTV.COM
DOCUMENT V1.2
Quick Start Guide
Related Series Models:
CAM-AHY-2D-3F-IRVP, CAM-AHY-5D-3F-IRVP
The product comes with the following components:
1. Camera Device.
2. L-Key for device adjustment.
3. 3pcs attachment screws and anchor pack.
4. Software CD.
5. Quick Start Guide.
Be sure no parts are missing from the product before
installation.
Information in this document is subject to change without notice. As our
products are subject to continuous improvement, Aventura
Technologies reserves the right to modify product design, specifications
without notice and without incurring any obligation. E&OE
©2016 Aventura Technologies, Inc. All rights reserved.
AVENTURA TECHNOLOGIES, INC.
HEADQUARTERS
48 Mall Drive, Commack, New York 11725 U.S.A.
Tel: +1.631.300.4000 Fax: +1.631.434.7000
INSTALLATION
1. Below is an overview of the parts of the
camera, showing how the completed
product would look.
Bracket Angle
Attachment Location
Bracket twist adjustment
2. Use the bracket base for locating drill positions
and attach the camera as shown in the rear
bracket diagram below.
The bracket has a cable exit at the bottom. The rear is a
soft sponge material to create a better degree of water
seal design around bracket – surface.
3. All positions and angle adjustments are done
via the locking hex nuts located on the rear of
the camera bracket. Use the l-key to turn anti-
clockwise to loosen.
Angle Adjustment Nut
Rotation Nut
NOTE: Caution not to remove the locking screws, they use a
set of locking teeth which will lock camera angle and
position to prevent any long-term drifting of the position.
4. CAD Dimensions Inch (mm)
CONNECTION & OSD
The camera has the following termination cables.
1. BNC Interface: Connect to appropriately qualified
cable and attach to the DVR / XVR recording unit.
NOTE: RG59 Cable should be of high quality and using pure
copper inner core, low-cost cables using copper over steel may
give unexpected results for video signal and should not be used.
2 Power Interface: Standard CCTV 12V power
connection, connect to a qualified regulated
supply.
DC12V (600mA): 12V DC power input terminal. Make sure
to follow correct polarity with the + as the inner pin of the
supply
Some models may include an OSD built into the cable,
whilst the device supports OTC (Over the Cable) control,
the on cable is here for when DVRs may not support the
OSD function from the recording device.
Control of OSD is simple with the little four direction
control, and push down to activate. We referred the push
as entering or OK in the rest of this guide.
OSD MENU USAGE
The camera comes with a typical set of parameters for
image output used by the camera. Using the OSD, you are
able to affect the camera performance to suit the
installation requirement of the device.
Note: You can also use the OSD from your DVR/XVR device if
the control over cable method is supported, check the manual for
this device.
Press
○
E to enter the OSD menu you are presented with
the following top-level Menu.
You navigate around using the
○
L Left,
○
R Right,
○
U
Up,
○
D Down positions using the control button. To
change or activate a setting press down
○
E entering. This
will activate or allow change the current position value.
The currently selected position is indicated by the two circle
as highlighted in red.
Where there is a ←ˡ on the right side of selection, this
indicates an option or will change to another menu level.
Note: From top-level menus you can Exit, to retain changes for
when the camera is restarted, you must activate the Save option.
BACK Goes back to previous menu options
NEXT Goes forward to next menu options
SAVE All modified settings you have changed will be
written to the camera memory, so when it’s reset or
restarted the changes made are kept.
EXIT Closes the OSD menu from the system, retaining
current changes, but only until the next power cycle of the
camera.
5.5 Inch ( 140 mm )
2.79Inch ( 71mm )
UD
L
R
E
1
○
1
○
2
○
3
3
BNC RG59
12V DC 5.5x2.1mm
WWW.AVENTURACCTV.COM
DOCUMENT V1.2
MAIN MENU is the top level main menu, select option
up and down control, will either select an option or
change the displayed information option setting.
When you have an arrow will let you select a sub-
menu option.
EXPOSURE Control the camera image settings.
SHUTTER: {AUTO {SLOWSHUTTER: Auto,
x1,x2,x3,x4,x5,x6,x7,x8,x9} MANUAL {SHUTTER SPEED:
50.100,250,500,2000,5000,10000,100000}}
AGC: Auto gain control adjustment.
BRIGHTNESS: Picture brightness level.
D-WDR: Digital WDR
{ON/OFF}
RETURN: Returns to the top level menu.
All numbered selection allows a left-right adjustment
value to be set.
SAVE&END You need to save settings
modified on the menu to be stored even after a power
cycle of the device.
BACKLIGHT Top Level Menu {OFF/ON}
WHITE BAL White Balance {ATW Auto}
D&N EXT IR LED / IR Cut filter change over status.
D
N Day to Night seconds duration.
N
D Night to Day seconds duration.
NOTE: Ext uses an external photosensor to detect light levels.
NR Top Level Menu Noise Reduction
2DNR Low Medium High noise reduction level.
NOTE: Noise reduction will reduce hard edges, but will also
soften the image edges. The incorrect setting may affect recorded
image storage size due to more complex image compression.
SPECIAL Top Level Settings
G AE
MIRROR {Off, Horizontal, Vertical, Both}
NOTE: Mirror provide a means when a camera needs to be
installed upside fitted, or when need to see image reversed.
DPC Dead Pixel Correction
NOTE: Dead pixel function is advanced to allow for white dots
which can appear on sensors. Each option in the DPC menu will
allow correcting each type, White / Black.
LANGUAGE: Selection for OSD Language.
ADJUST Top Level Menu {OFF/ON}
SHARPNESS {Level and Start – End gain control}
MONITOR Gamma, Blue Gain, and Red Gain.
LSC Lens Shadow Correction
OUTPUT MODE
FORMAT: AHD, CVI, TVI, CVBS.
VIDEO OUTPUT: PAL / NTSC setting
NRT: Near Real Time
{ON/OFF}
RETURN: Returns to top level menu.
NOTE: NRT is designed for recorders which don’t display images
in real-time. Normally this setting would not need to be enabled.
4
4
4
  • Page 1 1
  • Page 2 2

Aventura CAM-AHY-5D-212V-IRVP Quick start guide

Aventura
Brand
Aventura
Model
CAM-AHY-5D-212V-IRVP
Type
Quick start guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents