ALIBI ALI-CS1080P Quick Installation And User Manual

ALIBI
Brand
ALIBI
Model
ALI-CS1080P
Category
Security cameras
Type
Quick Installation And User Manual
1
www.observint.com
ALI-CS1080P_CQ
12/17/14
Notes:
• Lens: The camera accommodates a standard C or CS mount lens.
• Camera holder hole: Provided on the upper side and underside of the camera housing.
• Auto-iris interface: DC driven (DD). Mode uses Damp+, damp-, drive+, drive- pins.
4
2
3
1
Pin Function
1 Damping -
2 Damping +
3 Drive +
4 Drive +
Installation notes
Before installation:
• Make sure that the device is in good condition and all the assembly parts are included.
• Check the specication of the products for the installation environment.
• Make sure that the wall or the ceiling is strong enough to withstand 3 times the weight of the camera.
• To avoid re or shock hazard, use only UL listed power supplies. Verify that the power supply will
provide the rated voltage and wattage for the camera. See the Specications section.
During installation:
• Camera Lens: Handle the camera carefully to prevent scratching or soiling the lens. If the lens or IR
array shield becomes soiled, clean it only with approved products. See the
Cleaning section.
• Monitor impedance: Set the monitor impedance switch to 75 Ω.
• Power connector: The camera can be powered by 12 Vdc or 24 Vac. When applying 12 Vdc power,
observe the power polarity. The polarity is marked on the back panel.
Step 1. Install the camera mounting bracket
The camera can be attached to a mounting bracket on the upper side or the underside of the camera.
Follow the manufacturer’s instructions to attach the camera mounting bracket to the mounting surface.
Step 2. Attach the lens
The camera will accommodate a video-drive or DC-drive C- or CS-type lens. To attach the lens, do the
following:
1. Remove the lens protective cap from the lens mounting ring.
NOTE
• Use care to prevent dust from contaminating the area between the lens mount and the lens.
Install the lens assembly in a clean environment.
• The weight of the lens must be less than 2.2 lbs (1 kg).
2. If you are installing a C-type lens assembly, attach the C adaptor provided to the lens mounting ring
on the camera body.
3. Carefully screw the lens assembly clockwise onto the lens mounting ring (or adapter for C-type
lenses) until it is fully seated. Tighten until snug.
Auto-iris drive interface plug
Lens assembly
ALI-CS1080P HD-TVI Box Camera
Quick Installation and User Guide
The ALIBI HD-TVI 1080P resolution C-mount box security camera provides high-resolution video over RG59
coax or any standard analog CCTV cabling in diverse and challenging lighting conditions. A unique defog
setting improves the camera’s visibility in rainy and foggy weather conditions.
• High performance CMOS imager for high denition video
• Low illumination 0.01 lux @ (F1.2,AGC ON), 0 lux with IR
• ICR infrared lter auto switch
• OSD menu controlling, enable user to congure the detailed parameters
• 3D NR noise reduction
• Wide Dynamic Range (WDR) function
• Defogging function
• Auto white balance, auto gain control
• Support coaxial camera controller
Auto-iris drive interface plug
Lens assembly
Holes for mounting screws on top and underside
ALI-CS1080P camera (lens assembly not included)
Power LED
RS-485 D+, D-Alarm IN
Alarm OUTGround
D/N
Power input
terminations for
12 Vdc or 24 Vac
CVBS Video Out
HD-TVI
Video Out
Ground
terminal
Joystick
(for OSD)
Camera back panel connectors
What’s in the box
• Camera assembly
• This installation guide
Tools you need
To install the camera, you will need:
• C- or CS-type lens
• 12 Vdc or 24 Vac power source. See Specicati ons for wattage requirement.
• Pedestal mounting bracket
• Video and power extension cables
• Tools and additional fasteners (may be required) for mounting the camera
• CCTV video setup monitor (optional)
2
www.observint.com
4. If you installed an auto-iris lens, verify that the cable pin denitions match the lens output iris
connector, then plug the lens cable into the auto-iris interface plug (see above).
Step 3. Connect power, video, alarm, and RS-485 network
extension cables to the camera
1. Attach the camera to the mounting bracket. Holes for mounting screws are provided on top and
underside of the camera body. A typical installation is shown below.
2. Connect the ground terminal on the back of the camera to an earth ground. Follow all applicable
local electrical codes.
Power LED
Removable
power plug
CVBS (analog)
video Out
HD-TVI
video out
12 Vdc power
plug polarity
label
RS-485 D+, D-Alarm IN
Alarm OUTGround
D/N
Ground
terminal
3. If you are controlling the camera through an RS-485 network, connect the RS-485 D+ and D- leads
to the terminations on the back of the camera.
4. If you are using an external switch to control the D/N (day/night) function, connect one lead
(terminal) of the switch to the D/N termination on the back of the camera. Connect the other
terminal of the switch to ground.
5. If using the alarm input feature, connect the alarm sensor circuit to the ALARM IN and GND (ground)
terminals on the back panel.
6. If using the alarm output feature, connect the alarm sensor circuit to the ALARM OUT and GND
(ground) terminals on the back panel.
7. Attach the video extension cable from your HD-TVI DVR to the TVI BNC connector on the back of the
camera.
8. Connect extension cables for 24 Vac or 12 Vdc power to the power terminals on the back of the
camera. The power plug is removable for making connections easily. Observer the polarity shown on
the label for 12 Vdc powering.
Step 4. Power on the camera
9. Apply power to the camera.
10. While observing the video image from the camera on the monitoring equipment, adjust the camera
for the best eld of view using the mounting bracket adjustment features, and the lens zoom and
focus.
11. Congure your camera using the software menus in the on-screen display (OSD).
Step 5. Configure the camera with the OSD
Use the OSD (On Screen Display) to adjust the internal settings of the camera to customize it for the
installation venue.
1. Remove the cover on the underside of the camera to access OSD joystick and WDR switch. See the
photos above.
p
q
t u
OSD
joystick
The OSD joystick is used to open the OSD menu and navigate through the menus. To open the
camera menus and select a menu option, press the joystick down (in toward the base assembly). To
navigate the menus, rock the joystick up (UP (p), see photo above) or down (q) to move through
the parameter list menus vertically, rock the joystick left (t) or right (u) to change the parameter
value that appears for the parameter. Press the joystick down (in toward the base assembly) to
select the parameter value shown. Changes made to the OSD setup must be saved to be restored
after power o and power on.
2. Open the OSD menus by pressing the joystick in toward the base assembly. The OSD menu tree is
shown below. Use the OSD to congure the camera as needed.
MENU: Rock the joystick down or up to select either VIDEO OUT, LANGUAGE, or SETUP.
VIDEO OUT: Rock the joystick right or left to select either NTSC or PAL.
LANGUAGE: Rock the joystick right or left to select either English, Japanese, CHN1, CHN2, Korean, German,
French, Italian, Spanish, Polish, Russian, Portuguese, Dutch, Turkish, Hebrew and Arabic.
SETUP menu:
• SMART FOCUS: Press the joystick in to auto-focus the camera. A number will appear on the screen;
when the number is stable, press the joystick in again to set the focus setting.
• SCENE: Rock the joystick right or left to select either INDOOR, OUTDOOR, INDOOR 1, or LOW-LIGHT for
the best image.
• LENS: Only MANUAL is available for this parameter. No submenus are present.
• EXPOSURE
— SHUTTER: Rock the joystick right or left to select either AUTO,1/30, 1/60, FLK, 1/240, 1/480, 1/1k,
1/2k, 1/5k, 1/10k, 1/50k, x2, x4, x6, x8, x10, or x15.
— AGC: Rock the joystick right or left to select an AGC value from 0 to 15.
© 2014 Observint Technologies. All rights reserved.
3
www.observint.com
© 2014 Observint Technologies. All rights reserved.
— SENS-UP: Rock the joystick right or left to set the SENS-UP to OFF or AUTO.
— BRIGHTNESS: Rock the joystick right or left to select the brightness value (1 .. 100).
— D-WDR: Rock the joystick right or left to set the D-WDR to ON to improve the image quality or OFF
to disable the function.
— DEFOG: Rock the joystick right or left to set the defog function to OFF or ON. When set to ON,
press the joystick in to open the submenu. You can set the position, size, and the defog gradation.
• BACKLIGHT compensation. Rock the joystick right or left to select either OFF, WDR, HSBLC, or BLC.
— WDR (Wide Dynamic Range): Press the joystick in to open the submenu to set the:
GAIN: Set the gain of BLC as High, Middle, or Low.
WDR BRIGHT: Rock the joystick right or left to set the WDR brightness level (0 .. 60)
WDR OFFSET: Rock the joystick right or left to set the WDR oset level (0 .. 60)
— HSBLC: Push the joystick in to open the HSBLC submenu.
AREA: Rock the joystick right or left to select the area (AREA1 .. AREA4) you want to congure.
DISPLAY: Rock the joystick right or left to select either OFF or ON. If ON, press the joystick in to
open set the size and position of the area by rocking the joystick up, down, left or right.
HSBLC LEVEL: Rock the joystick right or left to set the HSBLC level (0 .. 100).
MODE: Rock the joystick right or left to select either ALL DAY or NIGHT.
BLACK MASK: Rock the joystick right or left to set the status to ON or OFF.
Default: Restore the HSBLC settings to the default.
— BLC: Push the joystick in to open the BLC submenu.
GAIN: Set the gain of BLC as High, Middle, or Low.
AREA: Press the up/down/left/right button to dene the BLC position and size. Select RET or
AGAIN to go back the BLC menu or redene the BLC area.
Default: Restore the BLC settings to the default.
• WHITE BALANCE: Rock the joystick right or left to select either MANUAL, ATW (Auto-tracking
White Balance), or AWCSET.
— MANUAL: In this mode, you can set the BLUE level and RED level (1 .. 100).
• DAY&NIGHT: Rock the joystick right or left to select either COLOR, B/W (black and white), and EXT.
In EXT mode, you can set the IR LED ON or OFF.
• NR (Noise Reduction).
— 2DNR: Rock the joystick right or left to select either OFF or ON.
— 3DNR: Rock the joystick right or left to select either OFF or ON. If set to ON, press the joystick in to
open the submenu:
SMART NR: Rock the joystick right or left to select either OFF or ON. If ON, press the joystick in to
select the sensitivity.
LEVEL: Rock the joystick right or left to set the level of noise reduction (0 .. 100).
START. AGC: Rock the joystick right or left to set the threshold level to enable AGC.
END. AGC: Rock the joystick right or left to set the threshold level to disable AGC
• SPECIAL
— CAMERA TITLE: Rock the joystick right or left to select either OFF or ON. If ON, press the joystick
in to compose a camera title. Navigate through the virtual keyboard by rocking the joystick left,
right, up or down. Select a letter by pressing the joystick in. Select RET to exit.
— D-EFFECT: (digital eect). This group contains the following features:
FREEZE: Rock the joystick right or left to select either OFF or ON.
MIRROR: Rock the joystick right or left to set the mirror (image ip) eect to either OFF, MIRROR,
V-FLIP (vertical ip), and ROTATE.
D-ZOOM: Dene the zoom area by conguring the position from PAN & TILT.
SMART D-ZOOM: A D-ZOOM area (AREA1 or AREA2) can be ON (enabled), and the position,
sensitivity and time are congurable. When motion is sensed in the D-ZOOM area, the area is
expanded to full screen at the D-ZOOM factor for the time (seconds) for which it is congured.
NEG.IMAGE (negative image): Rock the joystick right or left to select either OFF or ON.
— MOTION: Rock the joystick right or left to select either OFF or ON. If ON, press the joystick in to
open MOTION submenu. Select a MOTION area, set the
DISPLAY: Rock the joystick right or left to select either OFF or ON. If ON, press the joystick in to
open the DISPLAY submenu. In this submenu, set the size and position of the area to sense for
motion.
SENSITIVITY Rock the joystick right or left to set the sensitivity level (0 .. 60).
MOTION VIEW: Rock the joystick right or left to select either OFF or ON.
DEFAULT: Push the joystick in to return the settings to the factory default values for this menu.
— PRIVACY: Rock the joystick right or left to select either OFF or ON. If ON, press the joystick in to
select a PRIVACY shape.
SELECT: Rock the joystick right or left to select the privacy shape (AREA 1 .. AREA8).
DISPLAY: Select either COLOR, MOSAIC, INVERT, or OFF.
COLOR: Rock the joystick left or right to select a number (represents a color). Select a number
(representing a color ) for the area selected. Then, press the joystick in to position and set the
size of the privacy zone.
TRANS: Rock the joystick left or right to select a transparency level.
DEFAULT: Push the joystick in to return your settings to the factory default values for this menu.
— DEFECT: Use this feature to compensate for camera imager defects. LIVE DPC, STATIC DPC and
Black DPC are congurable.
• ADJUST
— SHARPNESS: Rock the joystick right or left to set the image sharpness level (0 .. 15)
— MONITOR: Rock the joystick right or left to select LCD or CRT.
— LSC (Lens Shading Compensation): This feature compensates the brightness of the image to
reduce the shading eect in image. Rock the joystick right or left to select the LSC feature to either
OFF or ON.
• RESET: Select to reset all camera settings to factory default conguration.
• EXIT: Close the OSD menu system.
Specications
Camera
Image Sensor: 1/3” Progressive Scan CMOS
Signal System: NTSC
Eective Pixels: 1920(H) × 1080(V)
Min. Illumination: 0.01 lux @ (F1.2, AGC on)
Shutter speed: 1/30 s to 1/50,000 s
Synchronization Internal synchronization
Video Frame Rate 1080p @ 30 fps
HD Video Output: 1 analog HD-TVI (BNC), up to 1080P
Video Output: (CVBS) 1 Vp-p composite output (75 Ω/BNC), up to 1000 TV Lines
Day & Night ICR
S/N Ratio > 52 dB
Menu
Scene Indoor, Outdoor, Indoor1, LOW-LIGHT
Camera ID ON / OFF (15 characters, position programmable)
AGC Support
D / N Mode Color / BW / EXT
White balance ATW, AWC-SET, Indoor, Outdoor, Manual
Privacy Mask On / O, maximum 8 zones
Motion Detection Support, maximum 4 zones
BLC Support
Anti-icker ON / OFF
Language English, Japanese, CHN1, CHN2, Korean, German, French, Italian, Spanish, Polish, Russian, Portu-
guese, Dutch, Turkish, Hebrew and Arabic
Function, Eclipse, Digital noise reduction, Digital zoom (62x), Slow shutter, Mirror, Defog, Defective pixel
correction, SMART D-ZOOM
General
Operating Conditions: -4 °F ~ 140 °F (-20 °C ~ 60 °C)
Humidity: 90% or less (non-condensing)
Power Supply: 12 Vdc, 24 Vac
Power Consumption: 12 Vdc: Max. 3.5W ; 24 Vac: Max. 5W
Communication In-line UTC controller (ALI-UTC)
Protocol: Pelco-C (Coaxitron)
Dimension: 2.74” × 2.28” × 5.70”
Weight: 13.4 oz (380 g)
4
www.observint.com
© 2014 Observint Technologies. All rights reserved.
CLEANING
Clean the camera with an approved glass cleaning solution and a lint free cloth.
• Dust can be removed from the unit by wiping it with a soft damp cloth. To remove stains, gently rub
the surface with a soft cloth moistened with a mild detergent solution, then rinse and dry it with a
soft cloth.
• Remove all foreign particles, such as plastic or rubber materials, attached to the camera body. These
may cause damage to the surface over time.
CAUTION
Do not use benzene, thinner or other chemical products on the camera assembly; these may
dissolve the paint and promote damage of the surfaces. Before using any chemical product,
carefully follow the accompanying instructions.
TROUBLESHOOTING
Problem Possible Cause
Nothing appears on the screen - Check the power connection.
- Check the video signal cable connection to the monitor.
The video image is dim or not clear. - If the camera lens is dirty, clean it with a soft, clean cloth.
- Adjust the monitor controls, if necessary.
- If the camera is facing a very strong light, change the camera position.
- Adjust the lens focus.
The screen is dark. - Adjust the contrast control of the monitor.
- If you have an intermediate device, set the impedance (75 Ω /Hi-Z)
properly, and check the cable connections.
The camera is not working properly and
the surface of the camera is hot.
- Verify that the camera is correctly connected to an appropriate regulated
power source.
The image on the monitor ickers - Make sure that the camera isn’t facing direct sunlight or uorescent light.
If necessary,change the camera position.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

ALIBI ALI-CS1080P Quick Installation And User Manual

ALIBI
Brand
ALIBI
Model
ALI-CS1080P
Category
Security cameras
Type
Quick Installation And User Manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents