ALIBI ALI-BC1080PVF Quick Installation And User Manual

Category
Security cameras
Type
Quick Installation And User Manual

ALIBI ALI-BC1080PVF is an HD-TVI camera that delivers high definition video resolution over standard analog CCTV cabling. It is ideal for security applications that require a high level of detail, such as facial recognition or license plate identification. The camera has a 1/3” CMOS image sensor and a 2.8 - 12 mm vari-focal lens with a viewing angle of 78° ~ 28°. It also features built-in IR LEDs that enable the camera to see up to 164 feet in the dark.

The ALIBI ALI-BC1080PVF is a versatile camera that can be used for a variety of security applications.

ALIBI ALI-BC1080PVF is an HD-TVI camera that delivers high definition video resolution over standard analog CCTV cabling. It is ideal for security applications that require a high level of detail, such as facial recognition or license plate identification. The camera has a 1/3” CMOS image sensor and a 2.8 - 12 mm vari-focal lens with a viewing angle of 78° ~ 28°. It also features built-in IR LEDs that enable the camera to see up to 164 feet in the dark.

The ALIBI ALI-BC1080PVF is a versatile camera that can be used for a variety of security applications.

1
www.observint.com
ALI-BC1080P_CQ
9/24/14
TOOLS YOU NEED
To install the camera, you will need:
• 12 Vdc or 24 Vac power source. See Specications for wattage requirement.
• Tools and additional fasteners (may be required) for mounting the camera
• Phillips #2 screwdriver
• Video and power extension cables
• CCTV video setup monitor (optional)
INSTALLATION
Before installation:
• Make sure that the device is in good condition and all the assembly parts are included.
• Check the specication of the products for the installation environment.
• Make sure that the wall or the ceiling is strong enough to withstand 3 times the weight of the camera.
• To avoid re or shock hazard, use only UL listed power supplies. Verify that the power supply will
provide the rated voltage and wattage for the camera. See the Specications section.
During installation:
• Camera Lens: Handle the camera carefully to prevent scratching or soiling the lens. If the lens or IR
array shield becomes soiled, clean it only with approved products. See the
Cleaning section.
• Monitor impedance: Set the monitor impedance switch to 75 Ω.
• Power supply: Camera drop cable: The camera drop cable includes two connectors:
Video BNC connector: For transmission of the video signal across a coax (75 Ω) extension cable.
Power connector: When applying 12 Vdc power, observe the power polarity. The polarity is
marked on the connector.
Mounting the camera
These cameras can be mounted on a wall or ceiling that has sucient strength to support it. The video/
power drop cable from the camera can be routed either through mounting surface or through a cable guide
on the edge of the mounting base.
Typical ceiling mounting
NOTE
If mounting the camera on a wall, ensure that the label on the mounting base, “Bottom,” is down.
If mounting the camera on a ceiling, orient the mounting base so that the cable guide is pointing
away from any source of water, dust, and other contaminates.
1. Using the drill template provided, mark the location of the screws that anchor the mounting base
to the mounting surface. See the note above. If you are routing the drop cable through mounting
surface, also mark the position of the hole for the drop cable.
2. Drill holes for the screws that anchor the base to the mounting surface. The mounting hardware
provided is appropriate for most surfaces. However, depending on the surface materials, more
appropriate fasteners may be required.
3. Drill a 3/4” hole through the mounting surface for the drop cable, if necessary.
4. Route the drop cable through the hole in the mounting surface, or through the cable guide in the
mounting base, then attach the camera assembly to the surface using the appropriate fasteners.
5. Connect the camera drop cable to video and power extension cables as required. NOTE: The
camera includes both an HD-TVI and CVBS video drop cables.
6. Connect the other end of the video extension cable to a video monitoring device, such as a CCTV
system monitor or HD-TVI compatible DVR.
ALI-BC1080PVF HD-TVI Outdoor
Infrared Bullet Camera
Quick Installation and User Guide
The ALI-BC1080PVF camera feature a 1/3” CMOS image sensor that delivers HD-TVI high-denition video
resolution over RG59 coax or any standard analog CCTV cabling. These HD video camera is ideal for security
applications that require a high level of detail, such as facial recognition or license plate identication.
Features
• CMOS image sensor
• HD-TVI technology produces 1080p HD video for sharp, detailed images
• 2.8 - 12 mm vari-focal lens with viewing angle of 78° ~ 28°
• Built-in IR LED enables the camera to see up to 164 feet in the dark
• Smart IR technology reduces over-exposure of the IR LEDs at the center of the image
• True day/night (ICR) captures sharp, clear images in low light and at night
• OSD (On-Screen Display) controls for customizing the camera settings for the installation venue
• -4 °F ~ 140 °F temperature operating range
• IP66 weather-rated housing
Camera body
OSD Controller
Lens Adjustments
Mounting
base
Sun shield
Lens
IR LED
Adjustable
mounting
bracket
ALI-BC1080PVF camera
Power
Connector
Polarity Markings
HD-TVI video BNC
Connector
CVBS video BNC
Connector
Camera drop cable connectors
Whats in the box
Video Test
cable
• Camera assembly
• Mounting hardware
• Video test cable
• Drill template
• This installation guide
2
www.observint.com
NOTE
Drop cable connectors are not waterproof.
7. Connect the other end of the power extension cable to a power source (12 Vdc or 24 Vac).
For 12 Vdc power, observe the polarity of the cable shown in the photo on page 1 of this guide.
Camera adjustments
8. Apply power to the camera.
9. Verify that video from the camera can be seen on a monitor. NOTE: Video from the CVBS drop able
or the video test cable is NTSC video and can be displayed on most NTSC compatible monitors.
Video from the HD-TVI drop cable must be connected to an HD-TVI compatible video recorder (DVR)
system.
10. While observing video from the camera, loosen the mounting bracket pan, elevation and horizontal
line adjustment lock screws, point the camera at your surveillance target, and then tighten
adjustment lock screws or nuts to hold the camera in position.
The mounting bracket pan adjustment can be made after loosening the lock nut (see the photo
below).
0° ~ 9
0° ~ 360°
0° ~ 360°
Use for horizon line adjustment
Use for pan
adjustment
(lock screw
Use for
elevation
adjustment
Camera mounting bracket adjustment
11. Remove the cover on the underside of the camera to access the Far - Near and Tele - Wide
adjustments.
Tele (T) -
Wide (W)
adjust
Far (F) -
Near (N)
adjust
Rotate
CCW to
remove
cover
for OSD
joystick
Slide right
and lift to
remove
cover-tool
Underside of camera body
12. Using the cover you removed as a tool, turn the Far - Near and Tele - Wide adjustment screws to
produce the best image.
13. Reinstall the Far - Near and Tele - Wide adjust cover.
USING THE OSD
Use the OSD to adjust the internal settings of the camera to customize it for the installation venue.
1. Remove the cover on the underside of the camera to access OSD joystick and WDR switch. See the
photos above.
OSD
joystick
p
q
t u
Plug for
video test
cable
joystick
WDR
ON / OFF
switch
The OSD joystick is used to open the OSD menu and navigate through the menus. To open the
camera menus and select a menu option, press the joystick down (in toward the base assembly). To
navigate the menus, rock the joystick up (UP (p), see photo above) or down (q) to move through
the parameter list menus vertically, rock the joystick left (t) or right (u) to change the parameter
value that appears for the parameter. Press the joystick down (in toward the base assembly) to
select the parameter value shown. Changes made to the OSD setup must be saved to be restored
after power o and power on.
2. Open the OSD menus by pressing the joystick in toward the base assembly. The OSD menu tree is
shown below. Use the OSD to congure the camera as needed.
MENU: Rock the joystick down or up to select either VIDEO STANDARD, LANGUATE, or SETUP.
VIDEO STANDARD: Rock the joystick right or left to select either NTSC or PAL.
LANGUAGE: Rock the joystick right or left to select either English, Japanese, CHN1, CHN2, Korean, German,
French, Italian, Spanish, Polish, Russian, Portuguese, Dutch, Turkish, Hebrew and Arabic.
SETUP menu:
• SMART FOCUS: Press the joystick in to auto-focus the camera. A number will appear on the screen;
when the number is stable, press the joystick in again to set the focus setting.
• SCENE: Rock the joystick right or left to select either INDOOR, OUTDOOR, INDOOR 1, or LOW-LIGHT for
the best image.
• LENS: Only MANUAL is available for this parameter. No submenus are present.
• EXPOSURE
SHUTTER: Rock the joystick right or left to select either AUTO,1/30, 1/60, FLK, 1/240, 1/480, 1/1k,
1/2k, 1/5k, 1/10k, 1/50k, x2, x4, x6, x8, x10, or x15.
AGC: Rock the joystick right or left to select an AGC value from 0 to 15.
SENS-UP: Rock the joystick right or left to set the SENS-UP to OFF or AUTO.
BRIGHTNESS: Rock the joystick right or left to select the brightness value (1 .. 100).
D-WDR: Rock the joystick right or left to set the D-WDR to ON to improve the image quality or OFF
to disable the function.
DEFOG: Rock the joystick right or left to set the defog function to OFF or ON. When set to ON,
press the joystick in to open the submenu. You can set the position, size, and the defog gradation.
© 2014 Observint Technologies. All rights reserved.
3
www.observint.com
© 2014 Observint Technologies. All rights reserved.
• BACKLIGHT compensation. Rock the joystick right or left to select either OFF, WDR, HSBLC, or BLC.
WDR (Wide Dynamic Range): Press the joystick in to open the submenu to set the:
GAIN: Set the gain of BLC as High, Middle, or Low.
WDR BRIGHT: Rock the joystick right or left to set the WDR brightness level (0 .. 60)
WDR OFFSET: Rock the joystick right or left to set the WDR oset level (0 .. 60)
HSBLC: Push the joystick in to open the HSBLC submenu.
AREA: Rock the joystick right or left to select the area (AREA1 .. AREA4) you want to congure.
DISPLAY: Rock the joystick right or left to select either OFF or ON. If ON, press the joystick in to
open set the size and position of the area by rocking the joystick up, down, left or right.
HSBLC LEVEL: Rock the joystick right or left to set the HSBLC level (0 .. 100).
MODE: Rock the joystick right or left to select either ALL DAY or NIGHT.
BLACK MASK: Rock the joystick right or left to set the status to ON or OFF.
Default: Restore the HSBLC settings to the default.
BLC: Push the joystick in to open the BLC submenu.
GAIN: Set the gain of BLC as High, Middle, or Low.
AREA: Press the up/down/left/right button to dene the BLC position and size. Select RET or
AGAIN to go back the BLC menu or redene the BLC area.
Default: Restore the BLC settings to the default.
• WHITE BALANCE: Rock the joystick right or left to select either MANUAL, ATW (Auto-tracking
White Balance), or AWCSET.
MANUAL: In this mode, you can set the BLUE level and RED level (1 .. 100).
• DAY&NIGHT: Rock the joystick right or left to select either COLOR, B/W (black and white), and EXT.
In EXT mode, you can set the IR LED ON or OFF.
• NR (Noise Reduction).
2DNR: Rock the joystick right or left to select either OFF or ON.
3DNR: Rock the joystick right or left to select either OFF or ON. If set to ON, press the joystick in to
open the submenu:
SMART NR: Rock the joystick right or left to select either OFF or ON. If ON, press the joystick in to
select the sensitivity.
LEVEL: Rock the joystick right or left to set the level of noise reduction (0 .. 100).
START. AGC: Rock the joystick right or left to set the threshold level to enable AGC.
END. AGC: Rock the joystick right or left to set the threshold level to disable AGC
• SPECIAL
CAMERA TITLE: Rock the joystick right or left to select either OFF or ON. If ON, press the joystick
in to compose a camera title. Navigate through the virtual keyboard by rocking the joystick left,
right, up or down. Select a letter by pressing the joystick in. Select RET to exit.
D-EFFECT: (digital eect). This group contains the following features:
FREEZE: Rock the joystick right or left to select either OFF or ON.
MIRROR: Rock the joystick right or left to set the mirror (image ip) eect to either OFF, MIRROR,
V-FLIP (vertical ip), and ROTATE.
D-ZOOM: Dene the zoom area by conguring the position from PAN & TILT.
SMART D-ZOOM: A D-ZOOM area (AREA1 or AREA2) can be ON (enabled), and the position,
sensitivity and time are congurable. When motion is sensed in the D-ZOOM area, the area is
expanded to full screen at the D-ZOOM factor for the time (seconds) for which it is congured.
NEG.IMAGE (negative image): Rock the joystick right or left to select either OFF or ON.
MOTION: Rock the joystick right or left to select either OFF or ON. If ON, press the joystick in to
open MOTION submenu. Select a MOTION area, set the
DISPLAY: Rock the joystick right or left to select either OFF or ON. If ON, press the joystick in to
open the DISPLAY submenu. In this submenu, set the size and position of the area to sense for
motion.
SENSITIVITY Rock the joystick right or left to set the sensitivity level (0 .. 60).
MOTION VIEW: Rock the joystick right or left to select either OFF or ON.
DEFAULT: Push the joystick in to return the settings to the factory default values for this menu.
PRIVACY: Rock the joystick right or left to select either OFF or ON. If ON, press the joystick in to
select a PRIVACY shape.
SELECT: Rock the joystick right or left to select the privacy shape (AREA 1 .. AREA8).
DISPLAY: Select either COLOR, MOSAIC, INVERT, or OFF.
COLOR: Rock the joystick left or right to select a number (represents a color). Select a number
(representing a color ) for the area selected. Then, press the joystick in to position and set the
size of the privacy zone.
TRANS: Rock the joystick left or right to select a transparency level.
DEFAULT: Push the joystick in to return your settings to the factory default values for this menu.
DEFECT: Use this feature to compensate for camera imager defects. LIVE DPC, STATIC DPC and
Black DPC are congurable.
• ADJUST
SHARPNESS: Rock the joystick right or left to set the image sharpness level (0 .. 15)
MONITOR: Rock the joystick right or left to select LCD or CRT.
LSC (Lens Shading Compensation): This feature compensates the brightness of the image to
reduce the shading eect in image. Rock the joystick right or left to select the LSC feature to either
OFF or ON.
• RESET: Select to reset all camera settings to factory default conguration.
• EXIT: Close the OSD menu system.
Specications
Camera
Image Sensor: 1/3” Progressive Scan CMOS
Signal System: NTSC
Eective Pixels: 1920(H) × 1080(V)
Min. Illumination: 0.01 lux @ (F1.2, AGC on), 0 lux with IR
0.014 lux @ (F1.4, AGC on), 0 lux with IR
Shutter speed: 1/30 sec to 1/50,000 sec
Synchronization Internal synchronization
Video Frame Rate 1080p @ 30 fps
HD Video Output: 1 analog HD-TVI (BNC)
Video Output: (CVBS) 1 Vp-p composite output (75 Ω/BNC)
Lens: 2.8 - 12 mm @ F1.4
Angle of view: 92° ~ 32°
Day & Night ICR
S/N Ratio > 52 dB
Menu
Scene Indoor, Outdoor, Indoor1, LOW-LIGHT
Camera ID ON / OFF (15 characters, position programmable)
AGC Support
D / N Mode Color / BW / EXT
White balance ATW, AWC-SET, Indoor, Outdoor, Manual
Privacy Mask On / O, maximum 8 zones
Motion Detection Support, maximum 4 zones
BLC Support
Anti-icker ON / OFF
Language English, Japanese, CHN1, CHN2, Korean, German, French, Italian, Spanish, Polish, Russian,
Portuguese, Dutch, Turkish, Hebrew and Arabic
Function, Eclipse, Digital noise reduction, Digital zoom (62x), Slow shutter, Mirror, Defog,
Defective pixel correction, SMART D-ZOOM
General
Operating Conditions: -4 °F ~ 140 °F (-20 °C ~ 60 °C)
Humidity: 90% or less (non-condensing)
Power Supply: 12 Vdc, 24 Vac
Power Consumption: 12 Vdc: Max. 7W ; 24 Vac: Max. 10W
Weather Proof: IP66
IR Range: up to 164 ft (50 m) approx.
Communication In-line UTC controller
Protocol: Pelco-C (Coaxitron)
Dimension: 11.84” × 3.97” × 4.23” (300.8 × 100.8 × 107.6 mm)
Weight: 1.54 lbs (700 g)
4
www.observint.com
© 2014 Observint Technologies. All rights reserved.
CLEANING
Clean the camera dome with an approved glass cleaning solution and a lint free cloth.
• Dust can be removed from the unit by wiping it with a soft damp cloth. To remove stains, gently rub
the surface with a soft cloth moistened with a mild detergent solution, then rinse and dry it with a
soft cloth.
• Remove all foreign particles, such as plastic or rubber materials, attached to the camera housing.
These may cause damage to the surface over time.
CAUTION
Do not use benzene, thinner or other chemical products on the camera assembly; these may
dissolve the paint and promote damage of the surfaces. Before using any chemical product,
carefully follow the accompanying instructions.
TROUBLESHOOTING
Problem Possible Cause
Nothing appears on the screen - Check the power connection.
- Check the video signal cable connection to the monitor.
The video image is dim or not clear. - If the camera lens is dirty, clean it with a soft, clean cloth.
- Adjust the monitor controls, if necessary.
- If the camera is facing a very strong light, change the camera position.
- Adjust the lens focus.
The screen is dark. - Adjust the contrast control of the monitor.
- If you have an intermediate device, set the impedance (75 Ω /Hi-Z)
properly, and check the cable connections.
The camera is not working properly and
the surface of the camera is hot.
- Verify that the camera is correctly connected to an appropriate regulated
power source.
The image on the monitor ickers - Make sure that the camera isn’t facing direct sunlight or uorescent light.
If necessary,change the camera position.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

ALIBI ALI-BC1080PVF Quick Installation And User Manual

Category
Security cameras
Type
Quick Installation And User Manual

ALIBI ALI-BC1080PVF is an HD-TVI camera that delivers high definition video resolution over standard analog CCTV cabling. It is ideal for security applications that require a high level of detail, such as facial recognition or license plate identification. The camera has a 1/3” CMOS image sensor and a 2.8 - 12 mm vari-focal lens with a viewing angle of 78° ~ 28°. It also features built-in IR LEDs that enable the camera to see up to 164 feet in the dark.

The ALIBI ALI-BC1080PVF is a versatile camera that can be used for a variety of security applications.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI